Ford PCM Software Reflash Procedure

Just want to show the procedure and what is involved in updating the pcm to the latest level. Many customers are now falling outside of even the emission warranty that would pay for this. Anything 2008 on can usually benefit greatly from a software update if there is one for their vehicle. I keep my vehicle updated with all the latest software as it brings improvements just like Windows updates on your computer.

[@rndemetro]

Just had my 2005 f150 5.4 3v pcm reflashed at Liberty Ford. Glad I asked for it. $119.00 plus tax ended up being $127.75 out the door. Dropped off at 8:30am and was out by 9am. Brakes feel stiffer, gas pedal feels stiffer, even the steering feels different. After driving it I noticed immediately the shift points got fixed. Seems like my gas pedal has to be pushed to half the amount as before, as well as the brake pedal. Feels like a new truck, especially the throttle. I was on Ford forums for about a year before doing this. I had hard starting problems, hesitation during acceleration, random rough idle, etc. They told me if any of the starting problems happen again to bring it back. Thanks Brian!

[@escapelover7970]

Thanks for the video. My Ford dealer won't even check for any updates, let alone do a reflash. I have told them about my concerns with shifting on my 2013 Escape 2.0. Here it is over 2 years I've been driving it, can't believe there is not an update. Really wish you worked at my dealership. I enjoy your videos.

[@cpspot]

EscapeLover What are your shifting issues? My wife has a 2013 Escape, 2.0 naturally aspirated with a 6 speed auto. It has been shifting funny since it was new. Most noticeable in the 2-3 shift under moderate throttle. Feels like it spends too much time in-between gears, followed by abnormally hard thump when the next gear engages. I bring it to the dealer and they say there's nothing wrong. If it was one of my $1500 beaters I would have sold it long ago, for fear of impending tranny repairs. I thought I was the only one.

[@thacryptojunior2619]

job security assholes

[@AndrewKidd14145]

We got ids at the shop and I didn’t know how to really use it but knew we could reprogram since they pay for it. After it gathering dust and finally diagnosing a truck with a pcm ground issue I’m doing it and it seems to be working I love ya m8

[@leviathanoctavio9491]

Questions: What is the name of the software for your laptop? 2. Can a scan tool do a flash? 3. Where do you get the software for your PC? How do you know when an update has been made to a Ford?

[@lohlofftz2006]

You can use the fordscan software...

[@dragomistu]

I paid $49.99 for 2 days, i have the Snap-on Pass Thru Pro III and laptop. Downloaded it worked good.

[@greggv8]

I've tried to flash a PCM in a 1998 Mountaineer but it refuses to communicate with it to do the flash, clearing KAM or doing the KOEO and KOER tests. It falsely claims there's a communications error. It also fails at doing the ABS service bleed. Anything that involves sensing when the brake pedal is pressed it fails to do. I do get an note about a TSB on flashing the PCM out of the vehicle. For reading and clearing DTCs it works. It also is able to set the tire size. I've used FORscan with the same hardware. That software does the KAM clear, the KOEO and KOER tests, no problem at all detecting the brake pedal being pushed. Unfortunately FORscan does not yet do ABS service bleed for 1990's Fords.

[@mrksouthern]

Ok, sounds good. I just want yo know what im talking about when I take it in. I appreciate you taking the time to answer my question, thank you.

[@user-lq4ki8kr7x]

BEAUTIFUL JOB THNX HOPE FOR MORE INFORMATION ABOUT TRANSMISSION SOFTWARES TO INCREASE OUR KNOWLADGE.

[@chanandler4567]

Thank you very much for this video. 👍👍

[@Heffeme1]

I took my 2011 Ecoboost F150 in to get the PCM updated per several transmission TSBs and your videos. I specifically requested a PCM re-flash and the Trans Adaptive Table be cleared per your advice. They ended up charging me 95 dollars. Is this not something covered by the 5 year powertrain warranty (I'm still well within by time and mileage)? Also, what is the drive cycle one should do to "re-train" the transmission table, as I'm sure they didn't drive the truck afterwards. How long until the shifting should settle down? Thanks for the great videos. They have proven to be a great resource to me.

[@andrewilliams1981]

Is there a way I can do this myself? I have a 2003 Lincoln Navigator and I just pull a used ECU off a 2003 at Pull-a-part. Will I be able to perform this ECU flash myself?

[@JLE1177]

What did u end up doing?

[@andrewilliams1981]

@@JLE1177 The truck slung a rod so I just parked it in my back yard...

[@anonanonme2463]

Thanks again for your reply's and great videos. Okay I go a VCM 2 and installed the IDS and connected everything; comm to vehicle, etc. BUT the IDS told me I'd need to re flash the VCM2 - okay? I did exactly what it said on the screen, pushed the button on it and wait for the beep, etc. Then initiated flash; told me it will take 40 minutes, watched KZbin videos and it came back VCM 2 flash successful. NOW I can not comm with the VCM 2 and all I get is a beep every one second. It was "bricked." Can not connect to VM2. So some hair pulling and A LOT of internet searching I found a guy with a "restore" procedure and he also included the filed. Okay I got nothing to lose; 1,200 dollar brick. Did what he instructed and installed the files and I got it back; comm and everything - yahoo.. BUT now since I enter manually my vehicle into IDS and tried to start the Program Module - it refused stating because vehicle was entered manually? I entered the vehicle info manually since it wasn't in the model menu. Entered the Tear tag number EXH1 and - yahoo showed my engine type and year, etc. I also tried to enter the calibration # shown on my scanner and was told invalid #? Is there a way to override this lock out when a vehicle is entered manually?

[@dallasjohnson1170]

What software and obd2 adapter are you running?

[@conor8321]

The adaptive tables learned by the trans. That's a nice clue. this is probably why my transmission is running so bad after the recent recall and reflash. My mechanic is suggesting it's a transmission solenoid and the issue was present before the flash. I would like to see if the manual table was reset. Clues are pointing to -> not likely!

[@jimbike8064]

Ford and dealerships charging for updates made necessary because of their own fault in engineering, is b.s. Should be NO CHARGE. Just bought a 2010 Mercury Milan. Dealership said due for update. Occasionally shifts a.little.late..

[@noahsmith8599]

As someone that works for ford there isn’t an update on that pos it’s called a recall lmao

[@jimbike8064]

@@noahsmith8599 if you work for Ford that may explain their crappy cars...lmaox2

[@syedakbarahmedsyedakbarahm2691]

Nice informative Video I ll still using IDS software In Saudi Arabia

[@mehrlstull8349]

I sure would like to speak with u in person

[@rzjk301]

Here's more information: vacuum gauge reads steady 25 vac at idle. Fuel pressure with vac connected is 31 psi.

[@Wannagobackto1980]

Hey man. I have a 2007 Five Hundred that I heard had an update due to the PCM causing surging when putting it in gear. And yes I have had it on a computer and no codes and says everything is fine so... I just need that done to it.

[@grenskie]

Hi, I am wanting to figure out if there is any kind of subscription or membership fees to use the IDS software? How much of this function or others are available for free?

[@charger6773]

If I go to the dealership what would I have to ask for to get this done ?

[@MatthiasHamilton]

Hi.. So can i ask a question... I know you're working with a ford model car here, but im sure the PCM and their functions are universal for any brand of car. So i have a 2009 Mazda that has been running fine and is still running fine in 2024. However last year The clicker that locks the car and sets the alarm, the interior lights (over the seats), and the Stereo in the car just stopped working and no longer function. There is also a door ajar indicator lit up on my dash even though no doors (or the trunk) are ajar. I called the dealership i purchased my Mazda from and told them about these issues and they told me my "PCM" may be "outdated" and needed a "software" update. This is the first time in 15 years I've ever come across something that has been wrong with my car being related to requiring a software update. So my question is with the features that I've explained here that are no longer working in my car. Does it make sense that yes in fact the PCM may need a software update (if not needs to totally be replaced). And if a software update is required to fix those problems how much should that run for a half hour's worth of labor? Thanks in advance! :)

[@carlosramos1543]

Thank you for this information I have a 2000 Ford F-150. how much would a reflash on the pcm come out to be $?

[@LaLito886]

Started having transmission issues with my 2007 ford fusion with 90000 miles. Wondering if this would help me with the problem I'm having. First couple of gears go in normally, but last one makes a hard kick. The car doesn't rev up, the gear goes in but hits really hard. Hope you can shine some light on the issue. Thank you.

[@user-pk7gk8ds6w]

I have a 2002 Ford lighting truck. I replaced fuel pump twice, my ford dealership said it was a bad fuel pump, IAC val, egr valve. Then they told me that they got a code, after they said the fuel pump resistor was bad. They just cleaned the rust off cause they couldn't get the part. I picked up the car, it seemed to be running good for 1 hour, then rough idle when at stop. Back to the dealer, now they say its a bad ground with the pcm. At this point either they are just guessing, or taking me for a ride. Could flashing pcm may fix fuel problems.

[@qwer153624]

I'm a ford technician and I have the VCMII. I updated too many ford PCMs but didn't notice a difference in performance like we see on Chrysler updates via wiTECH. What's your opinion ?Thanks for your videos BTW

[@waynebonham6452]

Hello, I watched your program and it seems to be a good one. By any chance did you purchased it from Ford or 3rd party. Thanks Wayne

[@radrickstheman2882]

I bought my Cardac plus 5 years ago and never had anybody buy a reprogramming. I think I will start trying to sell it harder these days.

[@luvkountry]

Hi, Great video on this subject...Wondering what type of devise/s that one needs to accomplish the reflashing of components.Do you have to subscribe to programs on the internet or from the various vehicle manufactures in order to receive the most recent updates.. Thanks for sharing this info..I'd have to conclude that the dealerships are charging an unreasonable fee to do the reflashes of the systems..Cheers and thanks for educating us...

[@FordTechMakuloco]

+luvkountry Everything you need to know is at www.motorcraftservice.com the prices for the equipment and yearly subscription are just not worth it for most owners.

[@Mrdubomb]

2014 F150 with 3.7 and a 6R80. Replaced transmission and now no start. I have no ckp signal or ckp/cmp sync on scanner. The crank sensor was removed but reinstalled after realizing you have to get at the torque nuts from the other side (duh). I thought possibly I put the ckp sensor in wrong, its a real pain to get that in there, but after doing it again I think its in correctly. The transmission was not reflashed, we thought it would at least drive to the dealer to get that done. No codes until I reset the KAM, and now we have a P1639 I had considered swapping the oe valve body due to the shift strategy issue and avoiding a reflash bill but boss said don't bother because of the damage to the old transmission. I'm married to this thing now, thanks for any help you can give me.

[@HC-xs6ek]

My 2010 Expedition is throwing P0130 and P0150, I hear this is a software issue and I need a reflash. Have you seen anything like this?

[@abdulazizalrashidi7518]

I got 2015 mustang gt and the Electrical power steering does not work, I have the ids software. I want to reflash the PSCM. what do i need to have? like files?

[@aliabdallah102]

You really don't need much idk what kinda creds. You'd need. (Creds as in like being registered with Ford not Ford credentials)

[@VinnieVega76]

Nice video thanks. Question; what software are you using to do this and how much did it cost

[@luiscalvetti3318]

sale of license and installation for original and cracked ford ids and fdrs at the best price without limitations, all programming systems unlocked, unlimited key encoding, built data download, integrated programming, sync programming, latest monthly ids updates, professional encoding with PTS accounts, 1 year license ids and fdrs

[@claudiuchirilov5307]

Nice video. What do you think about EAC fail error ? Do you think a reflash is necessary to overcome this issue ? Thanks in advance.

[@Fri3dPickle]

Do you have a video on how to flash the ACM on a 2017 Fusion? My radio keeps cycling, even when power is off, causing the battery to drain. The dealership wants upward of $300 to flash/reprogram it

[@HarshaNitw]

@FordTechMakuloco Great video. Can you tell me what accessories are needed for this job on 07 ford taurus? Thanks

[@juanduran9524]

Hola, tenía el codigo P060C en F150 2006 y después de manejar la camioneta por una o dos horas se encendia la llavesita en el tablero y se empezaba a poner pesada la camioneta. Le hice calibración a la PCM con la última actualización y se corrigió el problema, me cobraron por actualizar pcm 75 dolares en un taller

[@kfox468]

Have an 06 Lincoln zepher with transmission shifts problem. No check engine light. How much is a reasonable price to have it reflashed and all?

[@timluttringer9340]

I have a 07 mkz with the same issue did this fix yours and are you getting horrible mlg

[@GetOuttaDodge1]

On 07-03-2023 a local ford dealership updated my 2016 F150 PCM from "C" to "E" and immediately may my trucks transmission WORSE. Now, dealership wants to throw parts at it. What could of caused the truck to be un-driveable from a pcm reflash from "C" to " E".

[@orlandogotay9853]

Should a PCM update be done simply to be updated? My truck runs fine. 2011 Ford Expedition

[@orlandogotay9853]

I have the same question!

[@N9IWJ]

Church van e350 someone stole Catalytic converter’s, now wont shift out of first, ford says pcm was bad cannot get another anywhere,bought aftermarket new, ford dealer programmed it but it wants pats key code and this van has no chip key , how do you get rid of pats programming on a new never flashed pcm Thanks so very much for video

[@chvyman1]

Awesome information thank you

[@MegaTete123456]

First of all, thanks for your videos, they help me a lot......I need your advise regards a code that might be related with this video.... I have a ford freestyle 2006, 78000 miles, last month i had a wrench tool code (don't remember exactly the number ) but was related with the transmission,eather hot tempertur , low level .I checked the fluid and was low like a quarter...fill up the fluid and the code( wrench tool) is gone. Today i have a C.E. light, the code is P0106, that is related with " Manifold Absolute Pressure/Barometric Pressure Sensor Range/Performance" . Should i Reflash the PCM software? . The car is pretty new, only as drive like 7000 miles per year..... thanks

[@hughesy8290]

i have a warm start problem on my 06 Mondeo.. i.e the car starts all the time but if you have been recently driving it ten you get no control of the throttle and the battery and engine management lights stay on.

[@Desertsat]

READ THIS! Just had to put PCM in Son-in-laws 2013 F150 3.5 Eco Boost for coil driver malfunction Cyl 1+2 dead. (P2300-P2303) I used IDS with VCMii and 115.01. (China full chip) Got a used PCM but was unable to write a new VIN to it. PCM was exact part numbers DL3A-12650-EE that was the latest update. Could not write VIN to it using PMI. would shut off power to PCM when I tried to use it. HOW TO: Install PCM from Junk yard with the correct P/N and program Pats keys. It will show a code of P160a Module ID miss match. It will start and run but will have the wrong VIN. Ok unless you have emissions test to get through. To write the correct VIN to the PCM, load a session in IDS with the correct VIN. Go to Powertrain, Service function, Relearn Vehicle Data. This will write PCM VIN and other data from the BCM to the PCM. BOOM! correct VIN in a Junk yard PCM. I just did it. No promises on different IDS versions or Model years/vehicles but it worked for me.

[@mariohernanrodriguezescoba5429]

I have a 2004 ford explorer. 2 days ago I went out to start it got it started and shut it off then went to start it again and it would not crank or start. when you put the key in the ignition the theft light flashes every 2 seconds but when you turn the key to on position it stays solid for 40 seconds or more. How can I fix this problem? it will not let my suv start at all. the mechanic checked all fuses and relays and everything is fine. He put a new battery in it and not the problem. Checked the volts at the started and all is good.

[@gonzaloaguirre1812]

Installed roush supercharger had roush flash my phone but car bogs down and starts sputtering at wot. Shoots code p061b

[@n2cycles]

I have a 2008 ford 5.4 superduty xl. I want to add cruise and I've been told that you can add a steering wheel with cruise control and flash the PCM and have cruise. My local ford dealer has no interest in verifying this.

[@GetOuttaDodge1]

on july 3 2023 i went to a dealer with a "minor" 3-4 harsh shift, long story short a PCM update from "C" to "E" caused catostrophic issues with my 2016 F150 immediately. No codes, but the truck is undriveable. What do i do next? i need help, asap!!

[@CenobiteBeldar]

I have a 2000 Ford E250 5.4L I just replaced the MAF sensor and intake manifold gasket. Shop couldn't find anything with code P0171 and P0174 reappearing again. They recommend reprogramming or flashing. I wonder how much it should cost. The mechanic says a couple hundred to almost a $1,000 depending on make with Mercedes and Audi more towards the $1,000 mark.

[@mfuller2068]

I have a 99 Town Car Cartier . Is this process valid for this year model? Does this require any special hardware or is it just the scan tools and windows computer? Thank you for all your great info and help!

[@BigDaddy-xr1yl]

2001 Ford Windstar Code C1185 I replace both right and left brakes as well as abs sensor what could be my problem I am also replacing front driver side and passenger side wheel bearing...

[@MD-wq6on]

Vehicles have become way too complicated. I am ready to go back to my '98 Tacoma that is manual everything.

[@peacewarrior9500]

M D nah, the use of chips, modules and sensors have made cars more easily and objectively diagnosable and treatable/fixable, thereby taking out the guess work and notoriously subjective scamjob that had been taking place at the shops!

[@josros6021]

My windstar 2003 sometimes have slipping transmission problems mechanic said when scanned shows pcm refresh took it to Ford fisrt told me will charge $112 plus taxes then called don't need it don't know what to do now, any suggestions please

[@jsskunwar2000]

Hi, What is axle ratio in programming and how to find the correct value for it from VIN number or other OEM info? Please explain in detail.

[@MEMEARAVELA]

hi fordtechmakuloko i have a ford focus 2014 have a problem some times when i drive message say power steering fault during that key cycle work fine when i turn off and star over again no power steering hard to move and code c102d when i read live data of pscm say vehicle speed at 100 mph whe is stop, just calibrate pscm and work fine like 2- 3 days, where is the pscm?? in the same pcm have update pcm or is other place Power Steering Control module???

[@FordTechMakuloco]

+Meme Aragon C102D is high friction internal to the steering gear only fix for this code according to Ford is to inspect tire pressure and for binding in the front end and besides that to replace the steering gear. What does the speed pid indicate in the pscm and pcm when the vehicle is moving?

[@MEMEARAVELA]

+FordTechMakuloco pscm speed are 100 mph all time and in pcm show the right speed i try with other pcm second hand from march 2014 but need to rewrite vin on that pcm i use launch x431 but cant find where write new vin thanks for help my friend

[@franksconglomerations5366]

I know this video is old, and this is a long shot, but I'm at a loss and really need some guidance since my local shop has had my car for 7 months and nothing has been fixed. They put 3 pcms in it, and its stays in failsafe mode. I know this is a stretch, but I could really use your knowledge and professional help.

[@mediocre-motorcycle-modifi6818]

Is there anyway of uploading a different calibration? Or making your own and uploading it?

[@FordTechMakuloco]

+Mediocre-Motorcycle-Modifications Yes aftermarket tuners do it all the time.

[@georgestepanov4789]

Hi Brian, do you know if VCM 1 you are using on this video still able to work with latest IDS 123 version? I am thinking between used OEM VCM1 and new VCM2 clone to perform PCM reflash... Thanks!

[@clydeelliott90]

I have a 2003 f250 6.0, I was tuning my truck and half way through the tuning my batteries had died on me and now my truck doesn’t turn over or anything, what do I have to do to fix this

[@Daniel_ATL]

I have a problem with P1299 and replaced all the coolant sensors, Cylinder head temp sensor and thermostat but i still have the problem. Do i need to do this to solve it? 2015 ford Fusion 1.5T

[@rzjk301]

Here's a interesting update... I saw your other video on clearing the PCM and to my surprise it took care of the P0306. In mode 6 there are no misfires recorded. The only test I have an issue with is TID: $42 CID $12 I think that has something to do with DPFE. In the drive cycle only the evaporative test is still running. I guess my truck had learned a bad habit and thought it was normal. I normally clear my codes using my obd2 scanner or my torque scanner. Now I know how to properly clear the PCM. Thank you.

[@gabrielpuckett7964]

what is the proper way to clear the pcm?

[@FordTechMakuloco]

Gabriel Puckett How To Clear your PCM'S Memory on Fords After Repairs

[@CapitolPilot]

Will this fix anti theft issue? My 07 focus has no crank with anti theft light flashing at me.

[@2vgod460]

Why won’t ford flash the 99-04 mustangs I have been trying to have my pcm flashed due to a tube stuck

[@mikem1014]

i have 98 mountaineer i replace ecm last year i have to go threw emissions next week an i see my ecm has no vin can i rewrite the vin with out IDS scanner... i have snappy 17.3 softwar an autel ts608 an autel 908 thank you mike

[@kevingibson5975]

Boy I wish you could reflash my 2005 mercury Montego. They told me at bailey Ford, its gonna be a 100 bucks to start .from the way that they are talking, I may be out of 300 or more bucks, when it's all said and done.

[@victorv4340]

I have a 2016 Mustang with a v6. I purchased it brand new 2 months ago with 235 miles on it. The 3rd day after letting it sit for 12 hours and after few minutes at high idle it dropped down to 600rpm's and started to shake as if it was going to stall. 3 different dealers said if no engine codes they can't tell what it is. they checked tsb's and only one service writer said there was engine idle problems but no fix. it does it every day after sitting over night. It goes to 800rpms then to 600rpms. 2 different dealers let me try other Mustangs with same engine and they go to 1200 rpms and then to 800rpms and then to 600rpms and no rough idle. it seems I'm missing 1 warm up idle. your help would be deeply appreciated.

[@JoseRamirez-ie2bk]

I have a Lincoln navigator but I replace the radio as I can do to program it?

[@Twanhines]

I just bought a 2003 Lincoln Navigator and the owner told me egr valve is bad. But while driving it its hard to drive. As in accelerating is difficult it acts like the transmission at times doesn't shift, like the transmission is geared one way and the computer is geared another way. It idles rough, and even when driving the low oil pressure light and high temp light comes on. It drives as if it has no power. I had oreliey put a code tester on it and they said that the ecu/pcm don't know if there's a difference was swapped out but not reprogrammed and the truck is in a stolen mode. Does these symptoms sound right with the brain needing to be reflashed or did I buy a dud? Thanks!

[@joseminano]

What tool are you using to do this procedure? I have an Autel Elite and an Auto enginuity

[@luisvaldez6204]

I'm trying to update the calibration on a 99 expedition. I get a FEPS circuit open or Ignition not on error. Theres no check engine light on... only code that I found and I think might interfere with the programming is Key-in circuit open..( The ground contact part broke off years ago.)

[@ooosoo8727]

Can doing this for my 2007 Ford Focus get it to finally start shifting gears again?

[@edwardgarcia6496]

can a scan tool mess up ecu i was messing with one of bluetooth now seems like theres short in my truck

[@FordTechMakuloco]

yes I have heard the cheap units can corrupt the pcm.

[@paulfiebke3909]

Sweet thanks

[@juliestandifer3892]

I have a Ford Freestyle 2005 and the brain was recently replaced. Now the cruise control stopped working. Can I get the PCM "brain" programmed? If so how?

[@jeansmith4845]

my 2004 f150 started doing rough idle and stalling while driving the other day its a 2004 f150 5.4l 3 valve i replaced cam shaft sensors as thats the only code it was throwing then it continued to do the rough idle and stall while driving i cleaned throttle body and it still did it now there is no throttle u can step on pedal and it does nothing i get message saying truck engine is in fail safe mode i cant move truck at all it still has rough idle and stall but now has no throttle what is the problem

[@dunkletx]

I have a 5.4L VIN Z 8TH DIGIT, SOHC, BI-FUEL 2003 F150 7700 work truck and I have already removed the propane tank (propane system is broken anyway) and have the engine torn down for other repairs. When I put back the fuel rail I intend to remove the propane rail and injectors using regular gas injectors. Is there an option using my forscan tool to modify the or disable the check for propane or is this a IDS procedure? I would like to be able to disable the propane option completely on my own so the PCM does not check to do the fail over to gas like it currently does. When the truck was built and modified in Canada it was reprogrammed with a new code 3U7AALA. Any advice would be helpful. I have not looked at the modules yet with forscan and would rather be able to use this tool if possible.

[@nicholaselias8542]

I know from past experience some car makes require very specific power supply to the PCM for flashing. Are Fords also that way? I know BMW's you can corrupt if you dont stay at above 13v

[@javieralejandrorevenga4816]

Excellent video. I would like to do this on my Ford Fiesta SES 2011. Do you recommend and Obd that work and not that expensive?

[@vr4095]

Tried to do on my hybrid escape. stuck because of some error with abs

[@randyelkins9311]

Will this fix my 2002 mustang GT fuel injectors want work and fuel pump want work theft light is flashing

[@dannyt101]

Just took my 2004 ford explorer for pcm reflash for a p2106 code that send my car into limp mode wrench light and engine service light. How do i know if they realy flashed it? My code came up quicker then when it was cleared by scanner.

[@user-kw9ok6qi6v]

So do u actually have to have to put a used one in it if replacing it ..

[@americanpatriot2789]

Why in th fnck do you pay for updates to a system that obviously is not fine tuned from the factory?! I feel if you add nothing to the engine/car that effects performance than updates should be free to keep your FORD on the road longer...

[@WKMP-kn1vm]

So i just bought a used 08 ford edge a month ago today when i started it after work the whole car vibrated on idle the check engine light came on and it lagged a little. I made it home without stalling but it still vibrates on idle. Do you know what this problem could be. PLEASE HELP!!!!!!

[@BlueF350]

My 2004 ford explorer limited with a 4.6v8 has been sitting with a dead battery for a couple of years. It had the transmission replaced right before it was stored. Now upon startup, it shifts funny. It is parked at my moms until I can get to it but do you think that it needs a pcm reprogram? It is also saying advance trac off, traction control on?? Does the abs module need reflashed too??

[@txmami03]

Do you know if this reprograming works for a Lincoln Navigator or does it need a different program?

[@CarlosRamirez29]

Hey @FordTechMakuloco... Really thanks for the video. Got a explorer Limited '10 4.6 3v and seems like no one around can fix my precious SUV. Some people says it's the Transmission others is the computer or EPC. Want to know how can I get the Connector cable and the software for give an update a try? Everytime the gearbox have to change between 3rd and 4th gear became crazy. Like if the computer don't know what to do. But if I turn off the O/D and change manually there is no problem. Even I can hit the pedal and the gears never slip. Only when have to change between 3rd and 4rd is the problem. Need help from an expert because here in my country there is no a good Ford Garage working.

[@ampofoboadi]

Hey man. Cool video. Where can I get this IDS software? does this software show fuel trims and oxygen data too?

[@sandraburton9169]

DO YOU KNOW IF THE COMPUTER WOULD HAVE ANYTHING TO DO WITH THE TRANSMISSION NOT ENGAGING ON A FORD F350 6.0 DIESEL 2004. AFTER REBUILDING THE TURBO IT WOULD NOT ENGAGE

[@lickburner86esquivel91]

I have a 2010 Ford f150 v8 4.6l. I suspect the pcm may be bad. Got a crank no start. I can hear fuel pump coming on when I turn the key. My questionnis? Is it possible to replace the pcm without having to reprogram? Is there such thing as a swap out and done?

[@eduardojosereisdealbuquerq6360]

Amigo, boa noite, tudo bem? Tenho um FORD FOCUS GLX 1.6 MANUAL 2013/2013 SIGMA. Estou tentando ativar os botões de CRUISE CONTROL, mas, o ELMCONFIG parece acusar que não tem módulo PCM, pois, não mostra o modelo, nem versão do firmware. Minha dúvida, o módulo PCM existe somente nos câmbios automáticos? É uma peça física ou apenas um firmware na central? Pergunto, pois, estou com os botões do Cruise Control instalado s e os testes dos mesmos acusa estarem corretos, mas, no teste de estrada, não liga. Eu, via VCM IDS, consigo instalar o firmware PCM na central, para utilizar o CRUISE CONTROL em um SIGMA 1.6 manual?

[@dangerdavefreestyle]

It seems as tho the 3.0 engines have some sort of high idle problem. is this one of the ways to fix it?

[@Badboyzfitness]

Hi I have a 2000 Lincoln ls and on the dash it is saying rescu failure what does that mean?

[@FordTechMakuloco]

+#funadds the rescue module is not responding

[@dfwclusterrepair9559]

For programming like this is Ford online subscription needed? If so also needed for TCM, BCM, GEM etc?

[@FordTechMakuloco]

yes

[@dfwclusterrepair9559]

FordTechMakuloco thanks bro you got a number? I’m always needing help now and then and am gonna be jumping into mobile Flashing. I spoke with Ron a few times in the past but sad to say we lost a great guy! 😔

[@alaxandersupertramp6955]

does the pcm have to be in car to use your cvm tool? thanks man

[@fastbanshee1999]

I have a question when flashing a module from as-built data. I recently bought a 2012 mustang v6. The previous had been paying a shop to swap the 5.0 v8 in the car. They got so far and apprently went out of business. Long story short, the engine and trans are in the car but the pcm was lost (or stolen) i have the vin to a gt mustang so i can order the pcm through the dealer i work for. My question is this. I noticed when going through to program the pcm from as-built data, it stated that it was going to go through a "vin verification process" with all the other modules in the car, if the vin from all the other modules dont match off the vin i have the pcm for, what will happen? Will it brick the pcm? Will it still program?

[@Bigmink2000]

I'm looking to purchase a 2012 fusion and I was wondering if the dealership would do the PCM flash or what I have to have somebody else do that before I purchased the car and or after or should I not have at all due to not throwing a code ??

[@JoseFlores-xt6jg]

I took my 2002 Ford F-150 to the dealership and had them reprogram to as built because of SMOG check reasons(calibration ID not matching similar vehicles). My issue is that after they did that the calibration ID didn’t change. The guy at the dealership said my Computer had been permanently set to that calibration ID. Does that sound right or true? Can that be done? Or is he BS me?

[@joshmarmolejo7980]

Would this work on a 2016 Ford F150? I swapped computers and removed vats using hp tuners. Truck wont crank.