The only remanufactured starters I Recommend: (check fitment guide) amzn.to/3slXgjZ Forscan is a free Ford Specific Diagnostic Software: Download Here- forscan.org/home.html ELM 327 Adapter I Recommend- amzn.to/2GC6dBj As an Amazon Associate I earn from qualifying purchases.
@marcjorgensen Жыл бұрын
Ford said they only carried the Mororcraft reman, said they couldn't even get new for my 6.2. Were they misinformed? I got the Motorcraft!
@techguy9023 Жыл бұрын
The one listed on Amazon said it didn’t fit my 2016 F250 6.2
@GlassGarza5 ай бұрын
😂
@dcmkcbbq2 жыл бұрын
Thanks for the very helpful video. Some other observations I made during my 6 hours swear fest were- 1. 2 3" extensions rather than 1 6" worked better for me on the top bolt. The 2 3" extensions are about 1/2" shorter and let me back out the bolt almost all the way out of the hole before pinching the ratchet on the frame. 2. when working on the top bolt I found it easiest to have my body 90 degrees to the truck with my feet at the drivers side door. That allowed my hands to follow the curve of the starter easier to located the top bolt. 3. a 12 point socket is a lot easier to got on the top bolt to remove it. 4. If you are having a problem getting on the bolt, check for debris on top of the starter that might interfere with the socket. 5. Give each bolt hole a couple of short blasts of brake cleaner to help to remove any grit from the holes. 6. Make sure the neighborhood kids aren't around while you are replacing the starter. Good luck to all why try this.
@JAM93072 жыл бұрын
The two 3” extensions instead of one 6” helped a lot with the 1/4 drive. 2017 F150.
@timharder95552 жыл бұрын
I did the 2 3 inchers too. Worked better but had to use a wobble adapter too. Easily the worst starter iv ever tackled
@nuttynut542 жыл бұрын
I'm on day2 trying to change this starter on my buddy's f150, gots the 4.6 2v and the top bolts being a bitch to get at. And all the 3bolts are different on the starter 13mm the bottom, middle bolts gots a half inch and the top is a 10mm with no room to get a ratchet on even with 2 3"" extensions so idk what too do now ,, plus the exhaust manifolds on the way to go by the side
@jgk10000 Жыл бұрын
The single 6” extension worked for me. But idk how this feller had both hands up in the main area. I peeled my fender liner back until I could fold it behind the tire (didn’t try to do it gently, 17 yo truck who cares) then I snaked my left hand up there and over the frame palm up to guide socket to that top bolt. It seems impossible until all of the sudden you get it seated and then the bolt is out after 10 minutes of 5° turns. Now you think the worst is behind you until you’re holding the new starter trying to get the bolts threaded wtf
@willpower3692 Жыл бұрын
@@timharder9555I’ve done my Honda Crv, about to tackle the ford. I’ll let you know which is worse. At least you don’t have to remove the air cleaner, and coil pack.
@Akasuper4 жыл бұрын
Just removed the old starter on my 2004 f150 3v. The top bolt can absolutely go to hell! Thanks for the great video FTM
@JoshuaCasso2 жыл бұрын
That third bolt is from hell.
@Jim.D9 ай бұрын
Very helpful video, watched it 2 years ago and it helped me yesterday when it died at my local post office. 2 hours to remove the starter, walked it 1/4 mile down the road to a local rebuilder, he rebuilt it in 30 minutes, then I reinstalled it in less than 30 minutes. Thanks for all the great tips!
@K1LL3RGRN6 ай бұрын
I love the fact that Ford put the solenoid on the bottom instead of where it normally is. It really gets in the way of getting to that top bolt
@klikliks_service4 жыл бұрын
Been watching your videos a lot lately. I'm a diesel tech of 15 years and I just wanted to say I have a lot of respect for you and your videos. Always professional and always informative.
@tyrannusspissamentum4423 Жыл бұрын
Not sure how he makes it through them all without swearing. Unless it's all off camera lol.
@jaysmechs24572 жыл бұрын
This is honestly as good as a video on the notorious f150 starter can get. I have a 2012 Mustang and it's the same PITA with no space to fully torque anything. Really a ford thing. Thumbs up from me.
@jeffreyallen37773 жыл бұрын
Did mine yesterday. I took off the passenger side wheel like others have done. I have big hands and have a real hard time getting them into that tight gap around the starter. Also if you position a light right you'll be able to see the bolt which helps a lot. It is a little extra work to take off the wheel and the plastic well sheild, but if you've never removed one before it might be worth it. You can get the bolt with a 6 inch extension and a wobbler or a similar arrangement depending on what you have for tools. I electrical tape the wobbler flex joint to stiffen it up so you can easily position it onto the bolt without it flopping around and you can actually see what you're doing. Once you get that one off it's easy if you have a decent selection of wrenches. Definetly wire brush your bolts well and use antiseize as well as recommended and you will find the reassembly will go much better. I put a generous amount of antiseize onto the bolt and turn them into the holes before reinstalling the starter to reduce the chance of misthreading the soft aluminum. I use nickel based antiseize which works really well on aluminum castings. If you think this project is really hard replace your exhaust manifolds first and it will seem much easier.
@rototiller78 Жыл бұрын
Yeah, when you replace the passenger side exhaust manifold and gasket you have to remove the starter to get the room needed to do the exhaust manifold job
@rejmonwilson8 жыл бұрын
trick that I did, when replacing my starter, (I placed a piece of electricity tape over the hole on the top hole on the new starter, stick the bolt through it, which holds the bolt in place put the starter in place, this really make reinstall the top bolt easy to install). it is a pain but be patient, also check the starter cable wire harness. I live in Canada my wire harness was very corroded. Great video really help me to tackle this job.
@Will-2163 жыл бұрын
I can’t. My bolt/holes are pretty much the ground for the starter. I have an old school mechanical starter.
@jasontorian5046 Жыл бұрын
This is the Hardest easy repair ever...........Easy to understand....hard to do
@allgun13 жыл бұрын
Very helpful video, it took me 3 hours to remove the top bolt, my hand was bleeding there is just not enough room just to give my advice remove the solenoid there are 2 Philips screws and the solenoid pulls right out, now you have more room for your hands but it is still not easy to get to the bolt. I also used a short flexhead ratchet fine tooth. Good luck
@jaypezynavarro95343 жыл бұрын
I literally fumbled with all sorts of combinations of extensions untill I saw Brian’s video and I was like wow the most simple combo 6” plus a short socket damm should of known thanks for your video!
@lowccperformance405910 күн бұрын
100% the best tutorial for this on KZbin. Doing this job for a customer soon thanks!
@lowccperformance40598 күн бұрын
Update: got it done in 2 hours, pretty easy with the right tools 👍
@whitley28258 ай бұрын
Thank you so much for making this guide! I was able to fix my 97 f-150 all by myself (and I have never replaced anything ever). You saved me a ton of money. Now my truck, Buddy, can go another 420,000 miles! Maybe..
@kellyconstenius6763 жыл бұрын
This must be fake CG generated. No way you get under there and NOT come up with a few new words to ad to the urban dictionary.
@luisdelatorre63333 ай бұрын
Cg means computer generated so you're saying computer generated generated
@Varrvatos2 ай бұрын
I understand your frustration, the worst mobile call, especially when it was caked in mud and oil
@teenice894Ай бұрын
You must don't know who this guy is..... best Ford mechanic on KZbin hands down. So this starter replacement is peanuts for him
@lancebangwell20 күн бұрын
A walk in the park Kizanski
@rwzwiefka3 жыл бұрын
heading out to the driveway today in michigan to change my starter in my '03 Ford. Thanks for posting this video! I have never done one before, and in the cold its not going to be easy... appreciate the information you gave.
@Jeff-sc1df4 жыл бұрын
As usual, you make it look easy. I do not look forward to this on my '05 5.4 Great job 👏
@vince29972 жыл бұрын
I have the same year and engine except on a Expedition. Was it hard to do or does it take a good chuck of the day to get to?
@vince29972 жыл бұрын
@@claudrasberry8467 😂 lol
@stevenhambly61212 жыл бұрын
Its just shy of hell.but its possible.i think.
@nopleaseno2515 Жыл бұрын
2006 F150 2hrs in, 4 bolts twisted off, 2 of them in the housing. I’m in the rust belt. Absolutely ridiculous engineering. I hate ford, hate!
@iambrian817 жыл бұрын
I don't even need to do this yet but I love watching your vidoes on the F150's. I have a 2004 and I am sure I will be doing some these sooner or later. I didn't attempt the spark plugs and let a professional do it. I do wish you lived near me in Florida though to diagnose a ticking noise under my truck. Love the videos. Keep em coming.
@19baitmaster513 жыл бұрын
5.4 tick is usually cam phasors.
@TheMeanWolverine2 жыл бұрын
This was my first time watching one of your videos. I would say great job on providing incite and details regarding the tools, sizes and lengths that you recommend. Just an fyi for those here, my truck is a 2007 f150 5.4 motor. The little braided ground wire from the solenoid to the starter was rusted in half. Truck had turned over more slowly then normal several times over the summer but I didn't look into it at the time:(( Today it was 6 degrees outside and today is when the starter failed completely. No heated shop, no lift and no power tools. So not to bore anyone here is the best information that I have to share and it worked FANTASTIC. I ended up using a much smaller ratchet than anyone noted on this thread that I have seen. I will try to include a pic but here is the long and short of it... pun intended... is the ratchet I used is five inches long overall with a swivel head. To that I connected a 2 7/8" 3/8" drive extension, a 3/8" to 1/2" adapter and a deep well 1/2 drive 12 point socket. Overall dimensions were 6 3/4" for the ratchet, extension, adapter and socket. Oh and the top bolt took me less than five minuets to remove. The short ratchet allowed me to get one half of a revolution on each motion. It was the first time I danced under my truck after I got the top bolt out. Thanks again for the video, you got me on the right track. PS I tried to attach a pic without success. Sorry
@CanadianCampPurr5 жыл бұрын
Just bought a 2012 F150 thursday from a ford dealership, friday morning in costco parking lot, truck would not start. Towing company tried to boost the battery only one click told me it was the starter. Nice to have a 3yr warranty!!!. Great video!!!
@JamesSmith-no7fr3 жыл бұрын
Thanks much for your video. As with all your videos, well presented and right on the money. On my 2006 Ford LTD 5.4L, there was no way to get my hand up and over the starter motor for the top bolt. To solve the problem of access, I took off the wheel well shield and went in under the exhaust manifold from the top. I used a 9" extension on a 3/8ths inch with a swivel head connector. Just enough friction to break torque and just enough visibility to see the bolt . Cheers and Thanks Much.
@pkvillager Жыл бұрын
Great video. Just had to replace the starter on my ‘08 f150 that had 180k on it. Died on my wife this Friday in the pickup line at my kid’s school. Took me an hour and a half in 25 degree weather. I only used my 1/4 drive wrenches. My 3/8 extensions and wrench heads were too big. My 3rd dead of winter parking lot swap. Hopefully my last.
@jdreaper21764 жыл бұрын
I have a 1999 ford f150 4x4. Replaced my starter in 1 hour flat. Watched your video first made it alot easier. Thanks !! Love your videos. Spotted a broke off exhaust stud. My next project and next video you have. ✌👍
@davidherrera2676 жыл бұрын
Your video was very helpful and informative. I've never changed the starter before my life, and found myself in the unfortunate situation of having to learn. Your video made it manageable, thanks for uploading.
@cameronlemke49026 жыл бұрын
Thank you so much!😂 I had the right tools but I kept missing that top bolt and can’t get it but seeing the angle you went from I think I can get it a lot easier now, mines a 2004 tho but same set up basically
@suzannekelley97992 жыл бұрын
Thank you for the video! I've convinced my husband to let me try my hand at changing the starter on his F150. (The fact that it's Sunday probably has a lot to do with it lol). Whatever! Wish me luck guys 🙂
@christianwerner54507 жыл бұрын
Your video was a REAL HELP! Difficult job but your tip on using 6" extension was great! I ended up using a couple of shorter extensions together with a 13mm deep socket for the top bolt...it gave me about a 1/4" extra on what the 6" extension with a standard 13mm socket had... gave me a little better clearance past the end of the starter. Thankfully the hidden bolts spun off easily once they were loose. Really helpful video - THANKS!!!
@MrRexquando9 жыл бұрын
Shocked at how close the the exhaust and no heat shield. I never liked putting the starter at the bottom where it gets all kinds of road contact however that was before I had to replaced the starter in the wife's QX56. Nissan put the starer in the gallery under the manifold. Nice and clean if it hadn't developed dead spots. Had to removed the whole fuel system and manifold. No easy rides I guess. Great video!
@miamimike12875 жыл бұрын
Same with Cadillac Northstar 32 valve Holy Ship what a pain in the butt
@mikeaylward94024 жыл бұрын
Spot on! Spot on! Save me arse! I don't have flex-head ratchets & it made the project lengthy & difficult. I did take off the RF tire to give me some more room. Top bolt was a beyotch but coming in from the passenger side helped a ton. My truck is an '07, so the cross-member on the frame made accessibility even tougher. But, thanks. There are several "F150 starter" videos on KZbin, but yours helped the most by far! Again, thanks!
@robertvinscent65685 жыл бұрын
It is a great video, and I don't know why it's got thumbs down but whatever. Only thing that is kinda wrong depending.. using the factory nuts. If the new solenoid terminal post happens to be Zinc and you put a copper nut on it or vice versa, Now you have electrolysis occuring and it will be green and crusty in no time. At the shop we see remans come with copper/brass posts with zinc nuts all the time. Haha I think they want them to fail.
@HtownRO5 жыл бұрын
So what's your suggestion to this? Don't use the factory nuts? Or use the factory nuts on the new starter with the brass/copper posts? Wasn't sure what you were trying to clarify
@corvettebob96 Жыл бұрын
The video was very helpful. I almost took the truck to a shop to let them install a starter I purchased. 97 Expedition, 4x4 with a 4.6. The truck has oversized tires so I was able to crawl under it easily. As soon as I broke the battery cable lug to the solenoid, I was committed! ;) Probably the last warm day in Michigan until next April. It took some effort but I got the two bolts loose. I couldn't find the top bolt. After using a mirror to see up there, I noticed the bolt was missing. I will probably pick one up the next time I am at a parts yard.
@AzKaraokeVic10 ай бұрын
Thanks for putting up the video. Yours is one of the most well lit and clearest I could find. You made removing that 3rd bolt look easy. I had a helluva time trying to get my socket on it because I couldn't get two hands up there. My front steering linkage and trans cooling lines were in the way. I finally pulled out my digital inspection endoscope and that saved me.
@nobodyimportant548510 ай бұрын
I have this exact same problem. I had a steel plate that I also had to remove to get more access. I was finally able to snap a pic of the third bolt with my phone but need to find a combination of extensions that will allow me to get to that bolt. They definitely make it easy on the 5.4L engines!
@shogunMR3 жыл бұрын
Thanks for this you helped me with my 2010 f150. That top bolt is rough took a good 40 minutes to remove with hardly any room to turn the wrench, the rest wasn't so bad took another 40 min for the rest. Thanks
@jeorginadaniels92592 жыл бұрын
Hello, how did you get that top one out?
@shogunMR2 жыл бұрын
@@jeorginadaniels9259 just feel around for the bolt and then put a small wrench in there and go super slow if it's too tight get extensions and get a swivel in between the extension once you feel around for the boat it's pretty easy to get out there's just not a lot of room to turn the wrench till you just have to be patient and just turn only two clicks at a time with your wrench
@bowlweevil41612 жыл бұрын
great video good photography and explained very well, if you get a cordless ratchet those bolts and nuts will come off quick, I have turned wrenches for 50 years and that cordless ratchet is one of the handiest tools i have come across especially on tear down THANX!
@Sighlense6 жыл бұрын
Just replaced mine. The hardest part was finding the right hand(s) position while flat on my back. If that top bolt wasn't so clean and free from rust from being tucked out of the elements (came out pretty easy once i locked onto it) it would have been MUCH more difficult. Thanks for sharing this with us.
@yourmomsgames228 Жыл бұрын
followed to a tee. worked out well. thank you. i got a little lucky, previous owner must have changed starters before, because the 3rd bolt was not there. they may have had a hard time getting it out and decided not to replace it but i will be throwing it in asap.... maybe :)
@missyconway92656 жыл бұрын
Great video. My 03 occasionally wont start, sounds like starter, just a dead click sound. This video will help with my replacement, thanks
@harryjoebatdorf2 ай бұрын
Thank you ! I got it ! Used a new aftermarket starter . Thank goodness I don’t have thick hands .
@dillhole38524 жыл бұрын
I really appreciate your videos! I fixed my truck after watching one for the fuel inlet fault. Thank you!
@McGregor0079 ай бұрын
God bless your heart for this video. You saved Christmas for my family with this one pal.
@marcjorgensen Жыл бұрын
Makuloco to the rescue again! Thanks so much man, you really saved me some time. It still took me a couple of hours mainly because of having to take fatigue breaks. My starter failure on my 2012 Raptor was very unique. One of the solder points on the S terminal on the solonoid had broken loose you could move the terminal plate around and the starter would connect, even saw small arcing. Great video, second time I've used one of your walk through's. Leadframe the other! Really helpful channel
@schnoebelen23332 жыл бұрын
Wow just got done replacing my 07 starter you make it look easy my friend and might I add awesome video
@i94south349 жыл бұрын
Great job on this truck.I wish i had it that easy when i Changed a starter on a pre-2003 Crown Vic it was a total pain.
@FordTechMakuloco9 жыл бұрын
I94SOUTH Not sure if I have had to.
@ronbaker87742 жыл бұрын
1,333,071 views suggesting people searching for the professional's method of doing the job. And then some think they need to tell you how to do the job differently or better. Makes me laugh. Great camera work and description Brian. And thanks for all the other Ford videos as well.
@paullasseigne4 жыл бұрын
Just wondering why they don’t use a stud with a nut and lock washer for the top seems it would line up hold it in place while you start the other two bolts and I’m thinking that it would be easier to start a nut than trying to find a hole you can’t see
@cbeausoleil Жыл бұрын
Thank you! Most annoying yet satisfying DIY I ever experienced! For the 3rd bolt. I extended my ratchet about 14” or so toward the front past the mounts to get it off and back on.
@tomc815710 ай бұрын
I have to do one of these this weekend. Looks like a piece of cake. I've done much harder starters before, this one you can actually see.
@Junkboy8883 жыл бұрын
Great Video, lol The setting reminds me of working on my Cars in the Dorm parking lot in the Military. lol
@jeremycompton16777 ай бұрын
Hoping this helps me. Gotta tackle this bear of a job today. I looked at it... it made me sad. I've got large hands which isn't going to help. Hopefully I can get the starter out. Thanks for the informative video.
@ryangreer76552 жыл бұрын
Video still helping people in 2022. Someone else helped me by not installing the 3rd bolt... Never would have found out where to feel and find out l was even missing a bolt.
@ouchthathurts40763 жыл бұрын
Thank you bro. I just watched you're vid. And my roommates 98 ford f250 is working. I'm a Chef by trade. And it's so rewarding being able to fix something when you dont know how. Beer time!!!
@hecreg1514 жыл бұрын
THANK YOU FROM THE BOTTOM OF MY HEART. I REPLACED IT ON MY OWN.That one bolt was a pain i basically did it with out even being able to see it. 👍👍
@deontaedwardsmoneygenerato65332 жыл бұрын
i just did my starter replacement on my ford F-150 and the videos was so helpful thank you.
@JamesJohnson-ye1qb5 жыл бұрын
I've changed many starters, I'm old and don't want to fool with it! When it's cold out the rotor spins without engaging on the first try. Second it fires right up. Good video.
@brianl1586 Жыл бұрын
Excellent video, thank you for the help. Top bolt was not that bad. Thank goodness you can at least feel it (if you cant see it). Be careful not to get your hands stuck, if you do don't panic and hurt yourself!
@ridgid859 Жыл бұрын
Oh man I just got my hand stuck and did start to panic a bit. I used my other hand to tuck my fingers and got them out. Took a break after that..
@aarodriguez1984 Жыл бұрын
Great video! Changed my dads stater on his 2007 f150 in about an hour. Very tight fit for sure but patience was the key. Thanks again!
@terrywood1145 жыл бұрын
Great video, l have changed many on the many fords I have owned. I didn't know if I could get starter out of such tight area until I seen your video. Im use to the old ones like me lol. Thankyou.
@johnlong3842 жыл бұрын
Thanks for mentioning the nut sizes and the tight area on top of the starter in your nice info-clip. I have to do this on a neighbors 2007 F 150 and wanted take the right tools to her 'two-mile-away-house'. Take care and try to stay out of trouble!
@downtown8432 жыл бұрын
Very helpful video. For reinstalling, I had a very hard time until I realized that the rear of the starter (opposite from the gear on the front) has to go in high, while the front with the gear stays lower. Once I did that, I was able to slide the starter back in place easily before bolting it up.
@geraldwafer60232 жыл бұрын
Li
@dannypalmer77012 жыл бұрын
Nice work.I got all my training from him! Hes the best Ford Tech
@skyartrc82863 жыл бұрын
i always watch your videos to learn from you on ford trucks, you explain everthing so easily,thanks
@jeffbrown3963 Жыл бұрын
I don't mean to be a PITA but I ask all the aftermarket stores to test the NEW starter before I go through the trouble of putting it in. I've had new ones bad right out of the box. Most stores will mumble a little but do it. Great video!
@dreamingcode4 жыл бұрын
You have an excellent temperament for this plus dexterous hands and fingers. I would be cursing from Brooklyn to Kalamazoo
@jimvenizelos46493 жыл бұрын
I'm in process of removing a 2 yr old starter to get to exhaust manifold bolts. I think the tranny shop that rebuilt the transmission tightened the starter bolts too tight. I'm actually making up curse words (note scene from 'A Christmas Story' when the dad is in the basement).
@peterheiser22474 жыл бұрын
I always look for your videos when I need to work on my truck. Your were perfect with all of the information. Especially the need to have and use a 1/4 drive. Thank you.
@johnw81033 жыл бұрын
Nicely done, bud! I've been following you for awhile now and you do great walk throughs and taught me a lot! Thank you sir, for what you do.
@stevebishop19612 жыл бұрын
Thank you for your video. It saved me and made the job so much easier. I appreciate how you let us know exactly what ratchet extensions are best and how to reach the bolts. I was able to replace the starter myself. I am a handy person, with home repair, but not a mechanic. I was able to replace the starter on why f-150 with not too much difficulty. Using the 3/8 inch to break the bolts loose and then using the 1/4 inch to finish the job was a great suggestion. Thank you or the simple and realistic video. I have not subscribed to your page for future repairs!!
@bull16796 жыл бұрын
My husbands personal truck is down and he had to work on sunday. So, what is his woman for other than to make his life easier. This video made it possible for me to crawl my ass underneath and remove it for him. Thank you!
@gcorpus55586 жыл бұрын
Wow. ♡♡♡♡♡
@michaelmace9245 жыл бұрын
Sure
@1keykneedeep5 жыл бұрын
If its true - Your an amazing woman. 👍👍- mad respect
@stevehenrichs50915 жыл бұрын
YOU'RE A GOOD WIFE.HE WON'T FORGET THAT!
@robertvinscent65685 жыл бұрын
Crazy !! What a lucky guy.
@larryniidji2 жыл бұрын
You certainly do excellent videos. You do erk me in a way. I struggle to do the job and then you do it with an great camera view on top of that. Wow!
@knowair6767 Жыл бұрын
Why does this job look so much easier in this video than the POS I'm working on? Does this truck not have a sway bar? Mine is no where near as "open" as this truck in the vid.. I literally can't even find the top bolt..one things for sure,if/when I get the top bolt out, it's never going back in. 2 bolts or set it on fire!!
@asdwdfeef4 жыл бұрын
Good video thank you 👍🏼 If anybody is curious this works for a 2016 f150 as well.
@11cisneros3 жыл бұрын
I was curious thank you!
@LutherBuilds8 жыл бұрын
I feel your pain. I had to change the starter on my 02 Explorer a couple of years ago. I had it parked on an uneven section of grass when mine went out. So I had to first level my truck before I could jack it up to get to the starter. And because it was sitting on the grass, I didn't feel comfortable getting underneath it. So I had to take the front left wheel off as well as well as the splash guard. Even then I was only able to reach one arm in to work on it. Also a good tip is not to over tighten the bolts on the terminals. I torqued down too much and ended up breaking the posts on the solenoid.
@FordTechMakuloco8 жыл бұрын
+Joshua Luther Good Tip! Yes that is why I use a 1/4" ratchet to avoid breaking those terminals off.
@jowens11262 жыл бұрын
Thank you for this one. I only have experience changing starters on 96 and older ford's. I was surprised to see they don't have a hood over the starter gear.
@NateJacobMoore Жыл бұрын
I know this is an old vid but i referred to it prior to my swap. Great job btw, very helpful. Removing wasnt as bad as anticipated and was able to do it without removing the wheel like some other guys did. All about the right combo of extensions and a mini cheater pipe
@whowantstoknow43716 жыл бұрын
This video was so helpful to us we changed our own starter. Thank you so much for sharing great video.
@4swzb9 жыл бұрын
Very well demonstrated including camera work!!!...thanks for the up load.....
@FordTechMakuloco9 жыл бұрын
Thanks!
@blazekai23 Жыл бұрын
Thank you so much, your one of the only ones who showed the step by step
@USA--17762 жыл бұрын
Don't watch this laying down my brain thought I was laying under that starter when it fell. Over here jumping out of bed lol
@JDog172 Жыл бұрын
Took me 2.5 hrs to get starter out on 2013 f150 5.0L. Still not sure how I ever loosened that top bolt. Tried every combination of extensions available. Nothing wanted to work. No room up there. Almost gave up. Ground down a small socket to make it 1/8-1/4" shorter with a 6"-3/8 extension and that seemed to do the trick to loosen the bolt. Then took it out with 6'' 1/4 drive. Install was a little over and hour. When installing put a piece of tape over top hole, drill a hole in it and insert bolt. This will hold in place till you tighten it. Good luck to all that try this. On the hardness level I would rate this a 8 or 9, but still saved me around $350+ doing it myself.
@matts22273 жыл бұрын
Just did mine on my '14. What a pain in the you know what. I said words I haven't said in years. I only bled once, but got quite a few scratches. I think I'll write a letter to Ford this week and let them know what I think of this design. Thanks for the video though.
@GlassGarza5 ай бұрын
Thanks after watching video it took my about 20 min to remove
@johnsegard29482 жыл бұрын
Just changed mine with the help of your video. Once again thank you.
@fomoco14545 жыл бұрын
Using a stubby 1/4" & 3/8 ratchet helps a lot concerning the swing radius. Great video!
@RonnieG993 жыл бұрын
This is the best one by far. Thanks dude.
@RoughRaiders139 ай бұрын
I just changed mine on my 05 F150. Definitely not the factory starter cause the last jerk off to change it left the top bolt out completely and used some random aftermarket bolt from a bin on the bottom. Luckily I'm a real mechanic and fix things right so I got 3 new bolts, the right bolts, and installed it with no problem.
@tonylopez87666 жыл бұрын
Great video didn't realize how simple this is.
@mattbartolovich82283 жыл бұрын
You think?
@SmoothOpp92 Жыл бұрын
There isn’t a better video out period. 💪🏽
@JoeShopper3 жыл бұрын
It's nice that your truck is so high off the ground! Great access. Thanks for taking the time to make the video. It's VERY helpful!
@RaiderRaffa5 ай бұрын
Bro had me laughing when he said Awww for some reason this one “just fell “ out .. I guess beating it with a hammer had nothing to do with it 😂.. like always thanks for making great videos they help a lot !
@matthewmoore81254 жыл бұрын
Man you made that top bolt look easy! It took me a couple hours due to fighting withy the top bolt. Mine is a 2014 model v8 5.0. Thank you for the video tho
@jsmythib Жыл бұрын
I managed to tap mine with a hammer and get one last start to get home today. Doing this tomorrow, Thankyou for the walk though.
@juliansilverman44322 жыл бұрын
Good Job! And thanks for taking the time to explain step by step how to deal with a tiny space lol! 😎
@hyperlogos Жыл бұрын
Being on the ground I finally gave up on getting enough clearance to work from the end of the starter to get to the top 2 bolts. I installed the bottom bolt and got it snug enough to hold the starter in place, then the middle bolt same and loosened the bottom, then I assembled about 3' of extensions with a bunch of wobble near the business end and shot through the notch in the engine mount. Used a 1/2" 12 point with a blue towel to hold the bolt and managed to get that in. Then I could run the torque wrench from the front. I've just had the motor out though so nothing's on the front and no compressor in the way
@danc.3698 жыл бұрын
Excellent vid.just replaced mine today on my 86 F250..6.9l diesel.Only bad part was that top bolt,whew!I knew if I was stubborn enough I could eventually get it.Stupid shop wanted $381,,,I said,,nope,dont think so.
@zxtenn9 жыл бұрын
I just changed the original starter on my 96 Jeep Grand Cherokee 5.2 last winter here in NY. I came out from a appointment on one of the coldest days and it did nothing, not even a click so I took a 1/2 breaker bar and gave it a good smack then it started and got it home, went to Autozone and got a lifetime rebuilt for 100.00, one good thing about trucks is there is plenty of room to crawl underneath. I think it was on its way out for a while because cranking speed is vastly improved now, before I got the typical starter drag even with the Optima red top battery
@jayryan74736 жыл бұрын
I enjoy watching people buy the Optima batteries while I work at our auto parts store because we just laugh all the way to the bank LOL.
@Kwalafied426 жыл бұрын
I always hear they're trash only people who like them are sponsored lmao
@FoxMan777 Жыл бұрын
I watched this video for the reason of that 3rd bolt up top. And fo course your video breaks off audio right when you are dealing with that one. Still it gave me the answer as to how to approach that darned thing. So thanks for the video.
@FoxMan777 Жыл бұрын
Yeah that was fun. But... It's done. :)
@w.j.bendellr.c.flying.1037 Жыл бұрын
I found it easier to Jack up the car take the right front wheel off put a jack stand underneath it.And have in the front wheel off , you’ll have more room to get to the starter motor. Great Job ⭐️⭐️⭐️⭐️⭐️
@scottdashnaw23453 жыл бұрын
Red green would just sawzall the cab off of the frame then it would be super easy lol...
@travisbass82263 жыл бұрын
Now remember if woman don't find you handsome, they should atleast find you handy
@adrianm4212 жыл бұрын
Holy cow that last screw kicked my butt. My extensions were too long or too short. But this video helped me a lot. I appreciate it! Also I got the truck to start but right after it starts there’s a whistle noise. Best way I can explain it is if you ever driven a diesel truck and you’re on the highway it makes that whistle noise. It makes that noise right after it starts up. Idk if I should be concerned or not?
@kingcatman10 ай бұрын
The Expedition seems to be more of a challenge than the F150 as far as location.
@11cisneros3 жыл бұрын
Just did this on my 2016 f150, awesome video, way easier on a 2016, the starter fell right out once I had all 3 bolts out, that top bolt did take me 30 minutes tho ...