Honda 300 fourtrax clutch and one way bearing replacement

[@terrystock3197]

Man this was a very detailed video showed me everything I needed to know about changing the clutch on my 4 wheeler GREAT JOB

[@FourwheelerDoctor]

Thanks and thanks for watching

[@freightshaker116]

I am working on the exact same unit,..MAN!!!!, was this video EVER helpful, you saved me a butt load of time and frustration, thankyou!!!!

[@FourwheelerDoctor]

Thanks for watching and glad I could help

[@hoosiered471]

Dude, this was a very detailed and informative video that you narrated in a very clear and concise manner!! Well done!!!! Thank you!!!!

[@FourwheelerDoctor]

Thanks and thanks for watching!!

[@brianmcneese9659]

Contacted you a few months ago about a Honda 700 big red. Unit wouldn't move. Replaced the oil pump, sprocket and chain and first gear clutch pack. Found a couple of o-rings pinched or incorrect size. Unit works fine now. Thanks for your videos and information!!!

[@FourwheelerDoctor]

Thanks for the update. I have seen the o ring problem on some of the rincons but I thought they had it figured out before the started with the big red but I guess they didn't.

[@jmarion750]

Thank you makes it so much easier to disassemble now

[@outdoortexan114]

Thank you so much, best video for this repair. I would suggest if you have never done this, watch the whole video first it will save you some time.

[@metalpt1887]

This is the first time I'm writing a comment. Big thanks for your video, you're the best😁😁😁👌👍👍

[@FourwheelerDoctor]

Thanks and thanks for watching.

[@jacobmcnichol147]

You are the man, I really appreciate these videos and the important details you include 👍 thank you

[@charlescantrell6765]

Very helpful and is an heck of a 4wheeler doctor..ty so much.

[@FourwheelerDoctor]

Thanks and thanks for watching

[@staggerleesmancave8987]

Love the videos, brother. So helpful. hey man quick question, if you don’t mind: I’m trying to replace the starter clutch (one way clutch) on my 2006 Honda rancher TRX350TE. Is it necessary to pull the swing arm to do this procedure? Or is there actually room to work by just removing the air filter box, recoil starter, and electric starter? Any advice you could offer would be greatly appreciated. Thanks, Stagger from SLMC🔥

[@wyattpeacock8686]

Best video out there for this

[@FourwheelerDoctor]

Thanks and thanks for watching

[@joshuawhite7745]

I just wanted to say that this video was very helpful. Thank you for the extra tips . if you're fourtrax, we'll not go into gear. What else could be the problem? But the light on top shows it is

[@Gordon-o4n]

i have a 1990 fourtrax 300 4x4...will not move when i put it in gear (i bought it like that)...installed new shifter clutch, centrifugal and one-way bearing..(the kickstart now works at least)...quadrupled checked my work......still nothing....runs fine.....i can shift through all gears when running including reverse...driveshafts, diffs are good....but will not move......i don't mind splitting the engine.....but what should i look for when i do??...(your videos have been very helpful)....thanks for your time, efforts and knowledge!!

[@REVNUMANEWBERN]

Mine is slipping & I ATTEMPTED to adjust per the manual, but now NO clutch, is there a way to get back to where I was?

[@jcrowemusic]

This vid was so helpful. Followed it step by step and was able to get my clutch replaced. Could you post a video on how to replace the shifter return spring?

[@Dinoxt12]

Excellent Video...Thanks.

[@ExcitedGeoCave-iw9qv]

Thanks for the tip on that 👍

[@joesfamilyfarm]

Another good video. Thanks for sharing.

[@FourwheelerDoctor]

Thanks for watching

[@Mtucker7]

Do theses ebay kits hold up pretty well?

[@anthonyneedham3639]

Hey, I’ve been restoring a 95’ model by watching your videos. Thanks so much for sharing. My clutches are making a noise when I’m idling with it in gear…Is this normal for a break-in period?

[@dawsonswinamer829]

Thanks man I’m about do this to my bike this week end this should help out a bunch

[@FourwheelerDoctor]

Thanks for watching

[@chiefsartain7711]

Great video. Thank you

[@jinxiejones7465]

Hello. Can you help me please. I have (2) 300 TRX's 1988 & 1997. 1) For some reason the '97 "locks" up when shifting from 1st to 2nd, but it goes alright in 1st, then struggles to get R or N. Why? When I bought this bike it did have 2nd gear problems, I used to skip 2nd and go into 3rd no problem? 2) I stripped the '88 one to repair and do a transplant but I found 2 tiny ball bearing balls in the bottom of the engine case. The '88 bike was purchased for the use of parts, but now it seems I have 2 bikes for parts. 3) Can you offer advice or refer me to somewhere where I can read up on both bikes please.

[@CCCollinsw]

What is the piece that the triangle thing with ballbearings 3 of em sits in the piece on top of the shift clutch

[@brian7134]

I replaced mine using your video... Which is awesome but it is still slipping I messed with the adjuster and there isn't a ton of adjustment too much and it dies when put in gear. Back it off and slipping. any thoughts?

[@levibromie6621]

Would you happen to know the thread size for that reverse thread crank nut? i need to get a die for mine since i accidentally stripped it a bit

[@bunnyhall116]

Im confused on how these clutches work, especially the one way bearing...whats the outter clutches function and inward....wiuld replacing these make shifting easier....?

[@REVNUMANEWBERN]

I've never seen the inside of one of those cases, does the holes for the alignment pins have ANY chamfer on them?? would it help with alignment to put a chamfer or better one on the holes??

[@trglocke]

Thanks for the great video. What is the labor time for this?

[@terrybutlersouthernsound]

Great video!

[@FourwheelerDoctor]

Thanks and Thanks for watching.

[@Griffm-ll8oi]

What is the reverse threaded nut called? Mine is stripped and cant seem to find another.

[@leroywright6777]

I have the same 4wheeler and if it is slipping then that is what is wrong with it then the clutch. So I should do what you did in this video and it should be ok.

[@FourwheelerDoctor]

Yes if it's slipping while it's rolling at speed in gear then more than likely is this centrifugal clutch.

[@REVNUMANEWBERN]

18:37 View QUICK QUESTION, the adjustment screw, WHERE does it come in contact internally? Does it touch the TRIANGLE shaped piece or the part under it the arm shaped part?

[@hoacha1]

Great video.

[@FourwheelerDoctor]

Thanks for watching

[@Hungwaylow]

Will it hurt to ride it with a bad one way bearing. Everything shifts fine but when I turn off the 4wheeler I can still hear it or something spinning

[@FourwheelerDoctor]

It will not hurt but your engine braking will get to where it just quits working and it will continue to keep spinning when it is switched off. I have had folks ride them for year with no ill affects.

[@zacharydavis7191]

What size puller is that?? Or it doesn't matter?? First time owning one of these and my kick start went out so I'm changing my one way bearing on my 96 300 an thisnis my first time

[@FourwheelerDoctor]

I think I used either a 6" or 8" two jaw puller to get hte clutch off. They normally not on there very tight.

[@m.b8257]

I’ve been waiting for a new video.lol , do you ever work on the Honda act’s from the 80’s ?

[@FourwheelerDoctor]

I would work on them but there doesn't seem to be any left in my area.

[@davydacounsellor]

Hi from Ireland, Great info thanks my Kickstarter is really stiff to push down think it may be the one-way bearing, the TRX has been sitting for 10 years any ideas thanks.

[@daltonstrawser2392]

I pulled the side cover off and 2 washers had came off the one was for the kick start but I'm not sure where the other one goes any ideas?

[@FourwheelerDoctor]

I'm pretty sure the reverse shaft has the washer on it as well.

[@daltonstrawser2392]

@@FourwheelerDoctor that was it thanks

[@camsimpson2119]

Good video,Would it be ok to lay the bike on its side so wouldn't need to drain oil or would that risk loseing parts into the motor

[@FourwheelerDoctor]

Yes that is fine as well.

[@slapnutzracing2152]

Currently working on a 2000 suzuki 300 king quad 4x4 when I pulled the wet clutch I didn't take note of witch way the one way bearing went any info would be great.

[@FourwheelerDoctor]

Look very closely on the one way bearing. Most of the time they have an arrow on them or lettering telling which side is the outside.

[@oneinthapipe8115]

Does the secondary clutch ever need replacement or is it typically only the primary? Thinking about doing this to mine.

[@FourwheelerDoctor]

It's usually always the primary clutch that wears on these machines. Since the secondary plus is only engaged for a split second during changing gears it vary seldom wears out

[@bunnyhall116]

What's that clutch packs function...is it used to pull out in 1st gear or does it make it pull in any gear....just trying to figure out both clutch packs main functions......ty in advance...

[@REVNUMANEWBERN]

25:15 I bet a mirror with some light or a bore camera looking from the crack or back side would come in handy for that

[@njkay0033]

Would it be easier to reassemble if it was on its side or at least slightly tilt back?

[@FourwheelerDoctor]

Yes tilting it up on the side does make it a little easier.

[@dougrightmyer217]

I just installed the same clutch on my Honda and now while running you hear a spinning sound when in gear. Also when shutting the atv off in neutral it makes a loud knock or two. If you cut it off in gear it does not do it. Any idea as to what is causing this.

[@FourwheelerDoctor]

Did you get your kick started lined back up correctly on reassembly?

[@1eyewilly]

I'm not a Dr. but I did stay in Holiday Inn last night

[@FourwheelerDoctor]

Lol I use that one pretty regularly but some don't get it

[@CoryLovelace-xq9de]

@ four wheeler doctor when I pulled my cover the kick start shaft come out 98 300 can you help me out

[@CoryLovelace-xq9de]

@fourwheelerdoctor

[@FourwheelerDoctor]

The easiest way to get it back in is to slide the kick starter back on the shaft. Make sure the washer is still on the end of the shaft closest to engine. Hook the hook on the spring on the cast piece in the crankcase and rotate the shaft clockwise until the lever is below the stopper in the case. This is tough to explain. I am pretty sure I showed this process on my 300 engine assembly video. I will see if I can tag you in it.

[@FourwheelerDoctor]

Skip to 39:37 kzbin.info/www/bejne/hKnPgWZsqpqGetEsi=U1SwW2GFtVdrG5lE

[@CoryLovelace-xq9de]

@@FourwheelerDoctor thank you I found your assembly video just a few minutes ago

[@jasons3427]

if im on a real budget is the rtv gasket a bad idea?

[@FourwheelerDoctor]

Yes in most cases the paper gasket is needed for tolerance inside the engine. I put one together before without a paper gasket and it would not turn over because it was bound.

[@magnum0121984]

@@FourwheelerDoctor ok, new gasket it is. Thank you for the excellent video and advice.

[@srlbotanical]

Where can I buy the bearing and clutch? Any recommendation?

[@FourwheelerDoctor]

I think the ones I used in the video were OEM but I have had pretty good luck with the aftermarket ones that you can purchase off of eBay

[@morrisoncleg6926]

How do you know if you need a new centrifugal clutch or a shift clutch basket?

[@FourwheelerDoctor]

A very seldom replace shift clutches or shift clutch baskets. The way the clutches work on these bikes you can't ride the clutch so they very seldom wear out. However the centrifugal clutch will wear out and I still very seldom replace the basket unless it has grooves in it from metal to metal contact

[@morrisoncleg6926]

@@FourwheelerDoctor my dumb butt pulled a very very heavy trailer about a mile in way to high of a gear, now the thing shifts gears but barely has any power to the wheels. If I lift the wheels off of the ground they will spin while in gear. You think cf clutch still? I'm new to clutches and already have it ripped apart fumbling my way through it haha

[@FourwheelerDoctor]

@@morrisoncleg6926 yes it definitely sounds like your centrifugal clutch. According on how bad it's worn out you may have to replace your basket too.

[@morrisoncleg6926]

@@FourwheelerDoctorI am having trouble getting the nut holding it off, I know it's reverse threaded but have what looks like a pinned nut. Let me post a video and I'll share the link. Wondering if you have ever seen this before. Thank you for the feedback!

[@morrisoncleg6926]

kzbin.info/www/bejne/bZLbemSJd5eoaKc

[@gregoryjones1878]

How does the reverse shaft spring go, ?

[@FourwheelerDoctor]

It's hard to explain in words but the end of the spring with the multiple bends in it presses against the notch on the end of the reverse arm that rides on the shift drum. The straight part of the spring presses on the bottom of the crankcase. The spring will have tension on it when installed I'm just going on memory on this. So if this doesn't make sense just let me know.

[@rickfink464]

Well I never received my $300 steering knuckle and got a refund. No one has a steering knuckle for a 2000-2006. Yamaha Big Bear. But luckily I saw a Yamaha Big Bear for sale on Facebook Marketplace Sunday. So for $350, I got both steering knuckles, another motor and a bunch of parts I can sell.

[@FourwheelerDoctor]

Good deal!

[@gregoryjones1878]

Are you willing to sell any of those Big bear parts?

[@rickfink464]

@@gregoryjones1878 what are looking for?

[@colbsterg3362]

One way brewing got to split the case it’s by the clutches

[@colbsterg3362]

Bearing

[@dangolden5696]

Where are you located?

[@FourwheelerDoctor]

South Carolina

[@racingboy1779]

You didn’t say a thing about the clutch adjustment screw 😑

[@FourwheelerDoctor]

I normally don't adjust it unless there is a shifting problem.