Free up a Keyless Chuck

[@onjisan]

Dude, 6 years later and you're still helping folks. Just got my Dewalt unstuck using your method. Thanks so much.

[@darrenpeace7745]

Thank you, my drill chuck was stuck for a year now. After watching your video its now unstuck and saved me a few quid.

[@cah326]

After searching several videos, yours is the one that allowed me to free up the chuck on my drill in a way that I was comfortable to not damage it. Thank you!!

[@handymancraftglasgow]

Very welcome. I'm glad it helped 👍

[@immrnoidall]

I can't thanks enough, I've had two of these old heavy as hell drills. But I worked them to death but years ago the chucks got stuck like this. Now, thanks to you I just fixed them both in 10 minutes with a hammer, flat head screw driver, and a little machine oil. I had to tap turn, tap, turn, tap, turn about 50 times ,little by little , to get it turned all the way back in, to oil the chuck jaws and surfaces they slide on. then it just got easier and easier to turn them in and out. Now they go all in and out with a good spin. SOOO cool.

[@hoffwell]

Had a cordless drill jammed for months. One tap with a hammer and fixed - unbelievable. Thanks from Carlisle!

[@handymancraftglasgow]

Brilliant. Glad it worked for you 👍

[@FredHandscombe]

You are "The man" - fixed my drill bit stuck in chuck in 5 minutes with your hammer trick. Thank you big time!

[@handymancraftglasgow]

Glad it helped 👍

[@ndiemer5261]

Thank you from U.S. !!!!!! Mine has been stuck for a few years. had bought a new set. Took 45 seconds to fix!!!

[@handymancraftglasgow]

Fantastic. Just a pity it took a few years 😊👍

[@cayrick]

Although not born in Scotland, I inherited Scottish DNA through my parents and still quiver when I hear the pipes. The one thing we universally unconsciously accept is the economical solution to a problem is always the best solution. It worked amazingly well for me with both my Dewalt keyless battery operated drills. Thanks!

[@handymancraftglasgow]

Brilliant. Glad it helped 👍

[@cameronackroyd1220]

Legend! Fixed it in 30 seconds. For anyone that can't get the drill bit out at all, hit Down on the drill bit, as the 3 clamps are together on the bit, this force should realign them. It worked for me anyway

[@handymancraftglasgow]

Brilliant 👍

[@nonihodgkins635]

Wow this 66 year old woman finally got her drill bit out. Thanks!!!

[@handymancraftglasgow]

Well done. Glad it helped 👍

[@Can_non69]

Dude. You saved me. I thought I was going to the repair shop. Just a few minutes and I was back in business.

[@handymancraftglasgow]

Glad it helped. I don't like losing my drill to the repair shop.

[@ericbrauch5872]

I did the WD40 trick and it worked

[@michellem8229]

Oh my god! This fixed my drill! I had a part stuck in it too which I could not get out, I hit the top of the bit with the pliers and it freed!!! THREE HITS and done! 🤩🤩 thank you for this video!

[@handymancraftglasgow]

Glad it helped 👍

[@miguelcoka]

Thanks Mate! This finally got my stuck bit loose. Watched all these other videos for months now and using the wrench it worked.

[@handymancraftglasgow]

Glad it helped. Thanks for the comment 👍

[@carlaharper1298]

Of all the videos I watched for the problem I had with my drill which were the Jaws were stuck, yours was not only the closest one to my problem but the one that solved my problem. Although I had to tap a little harder than a wee bit, I still got them Broke Free, oiled and now my drill is working great! FYI this video works on Milwaukee drills as well!

[@handymancraftglasgow]

Brilliant. Glad it helped. It is a bit worrying hitting your drill with a hammer. Great when it works. Thanks for the comment and information about other drills 👍

[@Can_non69]

I had to do a little extra tapping but it worked in the end

[@charleswong9747]

Hey, just tried your gentle technique on a Bosch PSB 13RE keyless chuck hammer drill. Now it’s working again. Thanks for your video!

[@tommyknockerparanormalinc]

Thank you! I didnt need the hammer part but my chuck wouldnt open so I used the pliers on it while it spinned and it opened up. YAY! You are the sixth video that I watched and the only one that worked!! Saved me! Subscribed, thanks thanks thanks thanks

[@handymancraftglasgow]

Thank you. Glad it helped 👍

[@arturskupcus4618]

Thank you for the video. Saved my dewalt drill. Bit was stuck and even with grips couldn't get it loose. After some gentle hits with hammer on the jaws and the bit came out. And the chunk seems to work just fine now. Greesed it with silicone spray and good as new now. Thanks again. Saved me alot of time and some money.

[@handymancraftglasgow]

Brilliant. Glad it worked for you 👍

[@JP-kx6kr]

It worked! You are a hero! Bosch GSB180 not seized but sticking or jumping the gears when tightening. A couple soft taps with a small hammer and then sprayed in some silicon lubricant.👍🏻

[@handymancraftglasgow]

Brilliant 👍

[@jockpike]

I have a corded keyless chuck type Makita drill that's been lying in the shed for months seized solid' Went out and gave it a squirt of WD, a belt wi a hammer and it's back on the team, Many thanks for the tip.

[@handymancraftglasgow]

Brilliant. Glad it worked.

[@kellyb7321]

Thank you for this. My chuck was seized up badly. A few hammer taps, a few drops of oil, cycle the chuck as far as it will go one way then the other. Repeat about 10 times and I have full range again!

[@handymancraftglasgow]

Brilliant. Glad it helped👍

[@garvielloken3929]

@kelly b any issues since?

[@cg9856]

Legend. Thought I’d have to abandon my job half way through. This totally works! Mon the weggies!

[@handymancraftglasgow]

Brilliant. Glad it worked.👍

[@jeanjacque1577]

Going to try this on my makita. Bit been stuck in it for months . It's my most powerful drill but I have been using my Milwaukee hope it works

[@handymancraftglasgow]

Hope it works for you.

[@RonaldoIStheboy]

Absolute legend mate!! I borrowed my neighbours drill to do some DIY and one of the drill bits fell down the middle. I was crapping myself that I might have to bring it back not working. I was up all night trying to use tweezers to pull it out. Watch your video in Salford problem in less than 5-minutes thank you very much stay safe

[@handymancraftglasgow]

Thanks, glad it was useful 👍

[@jordanmooney4064]

Great bit of advice! Thank you. Spent two days trying to free up a drill bit on and off and this video had helped me in 2 mins. 👍

[@handymancraftglasgow]

Brilliant. Glad it helped 👍

[@chrisavery9257]

just did this with a jammed festool chuck.. took a few attempts, to get a bit of movement then put some oil down and its as good as new.. thanks so much

[@handymancraftglasgow]

Brilliant. Good to know it also works on Festool chucks 👍

[@albertklein7188]

Worked for me! Thanks. My drill had a hex bit in it which I could not remove and the chuck would not release. I used a drift pun punch and hammer to push all three jaw segments flush with the front of the chuck. That freed the chuck.

[@handymancraftglasgow]

Glad it helped👍

[@GeneCasto]

Thank you! You just saved me a lot of time! 😃

[@hawkesworth1712]

Don't forget that oil is your friend. I was just about to order a new chuck - then I took it off the drill and drowned it in light oil. Now it only gets hard to turn for about one full rotation half-way between full open and full closed.

[@abhijeetbhamburkar6834]

Hi, thank you for this video, I just fixed my Milwaukee M18 using your method, it's just superb and simple.

[@sarahbowden2983]

Wow - that's genius, and it WORKS! Got our drill wet, totally seized up, this was an instant fix - THANK YOU!!

[@handymancraftglasgow]

Glad it helped 👍

[@jaminloh]

Thanks for the tip. Couple of little taps and the chuck was loosened a little bit at a time and now it works great again.

[@handymancraftglasgow]

Glad it helped👍

[@karenwood6374]

Thank you! i got my old Dewalt back to working thanks to your video.

[@handymancraftglasgow]

Great to hear! Brilliant 👍

[@tiffam23]

Yooooo... Nice one lad.. Just saved me going to screwfix... Been stuck for two weeks. Appreciated

[@handymancraftglasgow]

Brilliant. Glad it helped you 👍

[@ladeisman1]

Thank you mi amigo. For all the effort to put a video out like this. Even these small fixes can make a big difference. 👍

[@handymancraftglasgow]

Thanks, I appreciate that 👍

[@lorajohnston4254]

Thank you, so much. You have spared me the expense of buying a new one. Cheers.

[@handymancraftglasgow]

Brilliant. Glad it worked for you 👍

[@JimJmad]

YES! About to order a replacement chuck when i watched this vid. One of my chuck clamps(?) was also slightly higher than the other 2. Tapped it lightly using a cold chisel and bingo! Chuck is fine. Thank you!

[@handymancraftglasgow]

Glad it helped. I oil the chuck every so often and not had a problem since.

[@JimJmad]

@@handymancraftglasgow great idea!

[@garvielloken3929]

​@@JimJmad Did you have any issues with it afterwards

[@billpaterson4133]

Nice to hear a normal accent I can understand 🤓. Glasgow Yorkshireman living in South Ireland married to the mad Irish wife. Got a new keyless diy drill BnD keyless chuck jammed so put it aside to take it in for repair. Left it too late and it was our off warranty. Fast forward to today and find your good self showing a simple method, couldn't find anything near as good on KZbin. Many thanks for the help and the time taken to upload. Again great to hear how English should be spoken 😎😆🤓

[@handymancraftglasgow]

Glad it helped you. I knew that one day someone out there would be able to understand me 😁. Thanks for the comment 👍

[@hamiltonsthoughts9226]

Did the trick for me too! Mine didn't have any sticking out further than others but was like yours as could tighten but not loosen. Slowly knocking it with a hammer as I turned allowed me to loosen it and then with WD40 I was gradually able to finally get the whole thing to loosen up. Thanks

[@handymancraftglasgow]

Brilliant. Glad it helped 👍

[@robercjones6860]

The trick of tapping the jaws worked even though I couldn't remove the stuck bit first - thanks.

[@handymancraftglasgow]

Brilliant. Glad it worked 👍

[@TshirtWetter]

Awesome video!! My chuck locked up because I left the drill outside on the truck one night and it rained . I couldn't figure out for the life of me how to take out the Phillips bit because it was rusted in . but with your help, I have gotten it out and fixed the chuck! great job!

[@handymancraftglasgow]

Thanks for the comment. Glad it helped.

[@tonyscott7989]

Great tip, worked like a charm on my chuck that was jammed. Soaked in WD40 now , seems like rust was the problem . Cheers Tony

[@handymancraftglasgow]

Brilliant. Glad it helped 👍

[@garvielloken3929]

any issues after using wd40

[@davidcounter4866]

Thanks! I'm going to try this when I get home. By the way, great to hear a Scottish accent after so long overseas.

[@handymancraftglasgow]

Thanks 👍. Hope it work for you and you get home soon.

[@davidcounter4866]

​@@handymancraftglasgow A quick update - a bit late, sorry about that. I have no doubt that your tip would have worked if I'd diagnosed the issue right. It turned out that a metal shard had got lodged behind one of the jaws, but thanks for your help, keep up the good work and stay safe

[@wessley4606]

Purple burglar.

[@Rico702Vegas]

Not an accent.. an impediment-huge difference. Spawned from years of drunks murdering the language, but you know that well, don't you?

[@davidcounter4866]

@@Rico702Vegas No. And honestly, wtf are you talking about?

[@thehandyuncle]

Man you are awesome. I spent 1 hour with luck. After watching your video it is fixed after couple of hammer taps....

[@handymancraftglasgow]

Brilliant. Glad it helped 👍

[@TonyBevilacqua]

Thanks for the help, had a similar issue. In my case I couldn't get the bit out at all, I used some vise grips around the bit, and hammered down on the vise grips, and this worked as well.

[@handymancraftglasgow]

Brilliant 👍

[@twocan90]

Thank you! Resolved my stuck jaws problem in less than 10 minutes

[@handymancraftglasgow]

Brilliant. Glad it helped 👍

[@carolinemiller7774]

Thank you!! My Dewalt chuck has been stuck for days. This worked! 👏

[@handymancraftglasgow]

Glad it helped!

[@Gerry2210]

Worked for me on my sons Dewalt. It was struck in the wide open position, going by what you said I knew the problem was with the three locking locking fingers. I tried , with a flathead pushing them back, heard a bit of a click from one of them, we were back in action. Not sure if WD is the best , it tends to dry things out and oil will make it attract dust, so I gave it just a smear of light oil in the crucial parts and hope to do it every now and again. Many thanks for the info. Greetings from Ireland 👍👍

[@handymancraftglasgow]

Brilliant. Glad it worked for you. I just used WD40 as it's in the van. I only use it if I think the chuck is getting a little tight. Still working fine and never had the problem again. Thank for the comment all the way from Ireland 👍😊. Always good to hear from our neighbours.

[@Robertrebor]

Just bought a DCD778 5 weeks ago and keyless chuck has become stuck. Dont have a wrench big enough but will borrow one soon to try this! Thanks

[@handymancraftglasgow]

Hope it helps 👍

[@madeleine1138]

Thank you very much. Mine was useless until I saw this and another video.

[@handymancraftglasgow]

Glad it helped 👍. Not a big fan of hitting drills with a hammer but sometimes....

[@my5cents4u]

MARVELOUS! My good old DeWalt loosened its dead grip with a few bangs on one of the 3 chuck claws! THANK YOU!

[@handymancraftglasgow]

Brilliant. Glad it helped 👍

[@richardlewis2488]

Thank you so much , I have a Worx Drill , was about to bu a new one , tapped it and now works !

[@handymancraftglasgow]

Brilliant, glad it helped 👍

[@classydays43]

Might use this to fix the drill at work. Swear I had half a mind to replace the chuck, but this will save a lot of time!

[@handymancraftglasgow]

Hope it works for you 👍

[@soundsfrench]

I found you through your video on the impact driver trigger fault, I left my comments on how good that was. Now I see this. I bought these two tools as a set [Impact driver and drill]. My drill also does this intermittently but the worst thing is that most of the time it won't stay tight. It's like the dead stop of the chuck when you release the trigger, causes the chuck sleeve to continue to rotate and loosen. The bit either falls out or is deep in the timber and I'm then messing around trying to grip it in the chuck again without bending or breaking the bit. I cannot emphasise enough how disappointed I am in pretty much all the cordless range of Dewalt. Unfortunately, 12 tools and 8 batteries, I'm stuck with them for some time. They will be replaced by another make as they go, though.

[@handymancraftglasgow]

Mine was similar to yours, a real pain to use. It was ironic when the chuck jammed as mine also came loose all the time. As I had the Dewalt battery I ended up getting the DCD996 (amzn.to/39kAHkK) as an upgrade. This is a much better drill and I have not had any problems with the chuck at all.

[@mcclure85]

Thanks mate. Fixed my drill in seconds after watching this . Chur

[@handymancraftglasgow]

Glad it helped 👍

[@headlush]

Hey, thanks! Was just about to head out & buy a new drill. Your post was much appreciated!

[@handymancraftglasgow]

Hope it works for you 👍

[@bhilo4477]

OMG! Thank you. I was bummed that my drill was stuck. You are a life saver!

[@handymancraftglasgow]

Glad it helped 👍

[@JK-de8sl]

A couple light taps on the nose of my Porter Cable and it loosened right up oiled everything down cleaned out the rust and she's good to go thank you man

[@handymancraftglasgow]

Glad the vid helped you 👍

[@rchrdschmidt]

Great solution. Thanks. Richard Schmidt, Jr. Bebra, Germany. My grandfathers birth town.

[@handymancraftglasgow]

Thanks for that 👍

[@BenEverett1]

I’m on my 2nd brand new DCD999 in 2 weeks and it’s the same problem as the 1st one with the chuck getting jammed. The first one I exchanged last week and now this one will have to go back for the exact same issue.

[@handymancraftglasgow]

Not good.

[@cputilitysolutions]

Great video, I've got the exact same problem with my DeWalt so I'll be trying this tomorrow and then lube up with WD-40 👌🏽

[@handymancraftglasgow]

Hope it goes well 👍

[@thek.p4899]

WORKED BRO.i just found a 19 yr old EPC14 black and decker used once by my old aunt stuck as. not now thanks heaps

[@handymancraftglasgow]

Brilliant. Glad it worked for you. That drill is an old classic.

[@thek.p4899]

@@handymancraftglasgow its looks brand new lol thanks to my aunty and you !

[@ekconley6429]

Thank you... I think?! I was able to fix my drill based on your advice... but that means no new set for me (the newer brushless version is on sale right now 😁)! One of the 3 'fingers' of my chuck was stuck all the way out, the other two were going in and out freely. The stuck one was out about an eight of an inch further than the two that were still moving though. I thought that seemed pretty bad, but hey, nothing to lose by trying to fix it. Alas, your video helped me fix it! I had to really work on it a few times, thought I may have been coming close to hitting too much and too hard, but it seems to be good now. Applied a good amount of oil, loosening and tightening the chuck to distribute. Thanks again!

[@handymancraftglasgow]

Good to get your drill working again 👍

[@FlickaFlame10]

Thank you so much! This kept me from having to replace the entire drill and bit. This is a life saver!!

[@handymancraftglasgow]

Glad it helped!👍

[@dvnobles]

Your video put me in the right direction, thanks! I had to go a few extra steps. In case this might help others, here's what I did. I tried your method. This did not free it, but did enable me to loosen it a little at a time. Tap, loosen, tap, loosen, etc. I noticed that one of the 'fingers' was definitely not staying level with the others. Regardless, I was able to get it open mostly by using my robogrips. Then, I drenched it in WD-40 (any good penetrating oil would probably do the trick) a few times. Drench, drain, drench, drain, try to turn. Now it is at the point of opening and closing almost normally - at least I don't have to try to use pliers to try to turn it anymore. I was proud to finally get a DeWalt having always owned cheap drills, but having this problem with the drill not being very old was very disappointing. Hopefully, this will extend the life although I'm sure the best fix in my case is a new chuck.

[@handymancraftglasgow]

Thanks for taking the time to write this. Very helpful 👍

[@garvielloken3929]

Did you have any issues with it afte drenching it in wd 40

[@dannobles8028]

@@garvielloken3929 It's been working since. I did have one instance where it kind of locked up. I tapped it with a hammer and it loosened it up - I think one of the chuck 'holders' was ahead of the other two or something. Other than that, it's been working fine since I had this issue about a year ago.

[@garvielloken3929]

@@dannobles8028 Thanks for the reply

[@glennrostron416]

Great tip, bet your lass wasn't pleased about the table 😂😂

[@kenshamrocm4959]

Mine happened to the same drill in this vid... I knew what needed to be done but i was hesitant... Cheers.

[@handymancraftglasgow]

Glad it helped 👍

[@edwilliams1638]

In my case the chuck jaws were rusty causing friction and freezing the chuck.. Tap with a hammer, rotate, tap, rotate until the jaws were fully closed. Then spin them against a sanding pad to polish them smooth. Oil, run in and out a few times and the chuck now operates smoothly.

[@handymancraftglasgow]

Brilliant 👍

[@vominator]

Yessir. Fixed mine this way with my awesome harbor freight mini ball peen hammer before seeing this video. I saw some using wrenches, but I did it the easy and lazy way because I found the little hammer first.

[@handymancraftglasgow]

Brilliant 👍

[@Cueyred]

Excellent. I could not get the bit out but realised one of the three jaws was slightly higher. I gave it a little tap with hammer and screwdriver head and it released immediately. Thank you

[@handymancraftglasgow]

Glad it helped. Feels counter intuitive to start hitting your power tools, even gently, with a hammer. But it is good when it works.

[@avacalvano6559]

I had this exact problem and wrestled with it for an hour before keying up this vid. Worked like a charm, thanks x 100

[@handymancraftglasgow]

Glad the video was helpful. Thanks for the comment.

[@harukananami6615]

OMG! It's like magic!! fixed my gear!

[@handymancraftglasgow]

Glad it worked 👍

[@davidfletchfletcher]

Cheers! Just watched this, nipped out and mended my drill in 3 minutes! Awesome.

[@handymancraftglasgow]

Glad it helped you. It's never happened to my drill again. Seems almost too easy a fix but seems to work.

[@kevinhoney1385]

Dude you are genius my brother. just a couple lite taps with a hammer it open up,i try an 18 inch pipe wrench it would not budge.

[@handymancraftglasgow]

It's a great feeling when that chuck releases after a couple of taps. Glad it helped 👍

[@rgswoohoo]

thanks, just used this myself, only mine was not tightening and was jammed wide open - tapping on the teeth with two screwdrivers and some WD40 did the trick!

[@handymancraftglasgow]

Brilliant. Glad you got it working again 👍

[@GangstaKirby3]

Very easy fix! My drill was back up and running in no time. Thank You!!!

[@handymancraftglasgow]

No problem 👍

[@wshuang6278]

I fixed my stuck chunk by your way, thanks a lot.

[@anazario2000]

Thank you very much for your help it work like a charm!!!!!!!!!! it fre up the chunk in no time!!!!

[@handymancraftglasgow]

Brilliant 👍

[@leebrown5591]

Great tip. Freed it up straight away. Mine needed a tiny bit of WD40 once it was unstuck as it then it was smooth as new.

[@handymancraftglasgow]

Brilliant. Glad it helped 👍

[@garvielloken3929]

any issues after?

[@stankosiek7923]

Excellent advice. Fixed 2 drills using the advice given. Thanks.

[@handymancraftglasgow]

Brilliant. Glad it helped 👍

[@SalvageOverhaul]

Mate brilliant! Spent hours trying to fix it and after this video it took less than a minute to fix it 😳 Now I’ve used so oil for lube, must have been some rust holding it shut

[@handymancraftglasgow]

Brilliant. Glad it helped 👍

[@WillJones-ui3gy]

Thank sir that worked on my drill it was down for a long time now im back working again those drill are very Milwaukee drill very expensive glad I got it up and running again thank you very much sir appreciate the good advice thumbs up

[@handymancraftglasgow]

Glad it helped you out. Thanks for the comment.

[@tonyblake7569]

Awesome video, thank you. Had a drill with the chuck stuck closed, 3 parts that hold the bit extended, and every video I saw was about replacing it but you have to remove the screw I couldn't get to. Tapping it with a hammer got them lose and finally works. Still have a little work to do but may save me from buying a new hammer drill.

[@handymancraftglasgow]

Great. Glad the info was useful for you 👍

[@tstaruch5487]

Holy carp! Thanks! Worked like a charm!

[@handymancraftglasgow]

Brilliant. Glad it worked 👍

[@LouAndrew-zv6ic]

Great tip lm from Samoa an island with no expert advice 👍

[@handymancraftglasgow]

Samoa, wow, that's a few miles away from Scotland! I'm no expert but everyone knows something that can help someone else, Glad it helped 👍

[@gmazloom]

Awesome 👏 that 🔨 taping worked for me, took only 2 minutes to fix 💪

[@handymancraftglasgow]

Brilliant. Glad it worked.

[@scotttrubee8642]

Thank you brother saved me mid hunny doo project. Lol

[@handymancraftglasgow]

👍

[@sultanaabdul9589]

Thank you so much.. brilliant tried it as watching your video and guess what?? Its off!!! Thank YOU

[@handymancraftglasgow]

Brilliant. Glad it worked for you 👍

[@sirmalus5153]

It looks like not only Milwaukee 18V drills have the problem then. I loosened a Milwaukee that was stuck a few days ago. Same problem as in this video. Milwaukee has come out with an updated chuck, maybe Dewalt need to do the same.

[@handymancraftglasgow]

I updated my drill to the DeWalt 996 - not had a problem with that chuck. Hopefully this vid helped you out 👍

[@abdulrahmaneldin30]

Thank you so much man, I was gonna buy a new one cuz it didn't open and just by tapping it with a hammer it opened

[@golukoju]

Thanks, this technique fixed this problem with my Bosch EasyImpact 550

[@handymancraftglasgow]

Fantastic. Good to know it works on other drills as well 👍

[@ChickstasHobby]

I was just given a bunch of tools and to my surprise, the dewalt 20v max xr hammer drill was in the box without a battery and to my surprise, i used my battery it worked but could not for the life of me unscrew it. There was no bit the teeth were closed.. Your hammer method and a little bit of wrench action it unscrewed and a little bit of wd 40 i got a 130 drill for free. SCORE. Thanks for the tip.. It also came with the 20v max impact driver *(not xr) but still free is free

[@handymancraftglasgow]

Glad it worked 👍. These drills are worth every penny especially when they are free 😁. Nice one.

[@mgpowis]

Worked a treat, thanks for the tip

[@handymancraftglasgow]

Glad it worked 👍

[@rajsinghk1]

Absolute genius.. You just saved my day... Cheers 👍

[@handymancraftglasgow]

Glad it helped, its great when it works 👍

[@DM-cp4uk]

Banging on the kitchen table...missus must be sooooohappy!!!

[@handymancraftglasgow]

Let's not go into that 😁

[@TommyIsATwat]

Cheers for that, sorted in no time!

[@handymancraftglasgow]

Glad it helped 👍

[@jankizkhanz]

My chuck became stiff to turn yesterday after drilling some galvanized steel on a ceiling! So the knob used to turn easily by hand but now it needs a stronger grip to tighten! Why do you think? Did it reach its lifetime or could there be some steel debris in it?

[@GoGoHarris]

And it's still useful. Thanks for this

[@dashavillano6772]

Thanks, got it loosened up! Wd40 helps!!!

[@handymancraftglasgow]

Brilliant. Glad it helped 👍

[@Sailaboat]

Thanks mate, your vid got me out of a spot of bother 👌

[@handymancraftglasgow]

Brilliant. Glad it helped you 👍

[@hamdanmunir413]

thaaaaanksss. i though i have to buy a new drill. but after i saw this video i made it.

[@handymancraftglasgow]

Brilliant. Glad it worked for you 👍