Front wheel bearing replacement on Volvo XC70 P3 Platform

Рет қаралды 16,261

Күн бұрын

Пікірлер: 95

@studi1231 2 ай бұрын

It's really great that in your videos you mention if you make a mistake, so others can avoid the same mistake by watching the video. Thank you for the video, and keep up the good work! I haven't been following your videos as much since I switched car brands, as I needed more seats than just 7. But Volvo is always in my heart, and it's great to come back and watch your videos because you've always been a Volvo lover and you take great care of your car

@volvosweden 2 ай бұрын

Thx for the comment. Maybe one day you will be back to Volvo.

@studi1231 2 ай бұрын

Absolutely

@rosuadonis8562 2 ай бұрын

Mate...the timing is unreal :) I need to do this job on my xc70 and I was think about it just about when you uploaded the video.

@volvosweden 2 ай бұрын

Nice!

@firstlast8281 2 ай бұрын

Same here. Mine are starting to cause vibrations as well. Perfect timing.

@hugoburton5222 Ай бұрын

+1 for me xc60 t6 09

@ioancoste7665 2 ай бұрын

Mulțumim pentru postarea ta. Ai făcut un lucru profesional. Dacă toate serviciile ar fi așa ar fi bine. Te descurci și singur dar tot mai bine cu un ajutor. Salutari din România. Te urmăresc cu placere de fiecare dată!

@volvosweden 2 ай бұрын

Thx!

@pz5508 2 ай бұрын

You are a well expert to your Volvo car

@SlimTortoise 2 ай бұрын

Excellent thanks for showing the mistake. If you can make that mistake we all can.

@goneapetuono 2 ай бұрын

As usual, well documented and explained.

@paul-sg2uq 2 ай бұрын

Excellent video the way you explain the process is so simple to understand please continue 😊

@markryan6311 24 күн бұрын

Great video on this on this , enjoying the 2018 V90 XC.

@scottbarnes7094 Ай бұрын

Thanks for the info on the backwards seal, I had to go look at mine and I also put mine in backwards. )-: Better to fix it now than try to figure out later why the ABS is going bonkers! Good Video

@justincomisk 2 ай бұрын

Great video and much respect for showing the mistake. Working on my herd of volvos I've made a few too

@Pimpemans 2 ай бұрын

I don't own a Volvo, but it's on the shortlist for my next vehicle. I appreciate the effort put into filming it, the job is work enough just doing it. Subscribed!

@volvosweden 2 ай бұрын

Much appreciated!

@americanbeelady Ай бұрын

Loving all the videos, very helpful.

@andreypetrov79 2 ай бұрын

Как, всегда на профессиональном уровне подача информации! Спасибо большое за проделанную работу! Благодаря тебе мои два Volvo в порядке!!! Так держать 👍🤝

@virgis21 28 күн бұрын

Thanks for this video!! Well explaining! 👌 I’ve changed bearings for my XC70 also! 👌

@tommytulpe3926 2 ай бұрын

Again an excellent documentation. Thank you for that!

@AnthonyS80-V8 2 ай бұрын

Cant believe the rust on your front end. Extreme cold and salt with metal don't mix!! Here in Australia we don't have this issue Great job on the bearings without a hoist. I have used and would have used FAG ( made in Slovakia) from FCP. They give you a lifetime warranty. Your control arms are toast and should have been replaced with this job. I used Lemforder but in this instance Meyle HD is essential I feel Great video

@Koudie-ih4zr4 2 ай бұрын

Thank you for your professional instructional videos.

@АлександрКоролев-у8у 2 ай бұрын

Отлично сделано, осталось нижнюю шаровую в последствии заменить для полного счастья.👍

@volvosweden 2 ай бұрын

Летом надеюсь весь перед причесать 🤣👍

@АлександрКоролев-у8у 2 ай бұрын

Добрый день. Если можно ссылочку товара магаза (еБЭЙ) на сьемник.

@vinkey001 2 ай бұрын

What a job 🙈 Nice video again super !

@allatkalich2576 2 ай бұрын

Excellent!

@richardsanders2794 2 ай бұрын

Excellent as usual video.

@HERBYWALLACE3 2 ай бұрын

Helped me a lot thank you 😊

@nilssteinarholth1071 2 ай бұрын

Great work. Keep videos coming. 👍

@paulmacklin4201 2 ай бұрын

I've done this job on a previous P3. Not a particularly hard job but needs a press if you don't have one at home. I got mine pressed in a local garage.

@philipcook9772 2 ай бұрын

I had a problem with vibration and after many trips to the dealer,the last mechanic said it was the tyres,so 4 new ones where fitted.PROBLEM SOLVED.🇬🇧

@christopheparmentier2853 2 ай бұрын

Félicitations, excellent travail

@jct9w 2 ай бұрын

Alternative way of telling if your bearing failed is by just grabbing your wheel and try to wiggle it up and down, and if there are movements or play that means you need to replace them. Definitely check on both sides as I replaced my LF (driver side) and not both fronts, and turns out both need to be replaced. Took knuckle off was a very time consuming job so make sure whoever is taking it off and have it pressed in prepare a whole day for this. Few points on the ABS sensor >ABS message will go away shortly after a drive if you did not damage the abs sensor. >Pay attention to the ABS sensor as collision warning equipped cars are different than regular cars.

@volvosweden 2 ай бұрын

If what you describe is present it’s an extreme failure of the bearing. I catch mine at the Very beginning of failure.

@jct9w 2 ай бұрын

@@volvosweden Mine has 200k with the sound, so its definitely way overdue. If it's very light then yes you may need the stethoscope. Also just curious could you throw that link for the wheel bearing tool in the descriptions as well?

@volvosweden 2 ай бұрын

Look for the tool on eBay: search Volvo bearing tool. You will see it there

@frazerwiggins5616 2 ай бұрын

Well explained !! Great video And to show the mistake shows your human 🫡

@KKlepacki 2 ай бұрын

Very informative video. Thank you

@danieldoherty919 2 ай бұрын

Good evening, thank you for your lovely videos. I’ve been following you for a long time but once again you’ve used substandard Chinese parts and I did see one of your videos the other month where you was moaning about Chinese parts only buy original. I don’t really understand where you’re coming.🎉

@thejoseandresshow 2 ай бұрын

Could you do a very short video in which you show where you normally place the jack stands?

@volvosweden 2 ай бұрын

You are not the first one to ask. I will do it! Keep an eye out

@supersabrosinho 2 ай бұрын

Good video. The reason the ball joint didn’t pop sooner was because the hammer you used is too small. A 5lb hammer would’ve done it quicker

@LifeVacEurope 2 ай бұрын

I need to get these modules again, just waiting on my new to me 2011 V70 R Design T6 awd to arrive

@ADRIANSRT 2 ай бұрын

Any part numbers for the press kit used? Having a hard time finding one with an 82mm bit

@lonetraveler5660 2 ай бұрын

There is no way to refill the grease into the bearing? Thank you for the video tutorial. Maybe is possible to add grease through ABS sensor using a needle, based on your video.

@monospearmint3924 2 ай бұрын

Thanks from turkiye 👍

@Svensken8R 2 ай бұрын

Yeah see what some water, salt and dirt and debris can do.. I mean everything is so rusty. But you did good changing, replacing it yourself!

@mrslaharris7128 2 ай бұрын

❤❤❤❤Thank you

@MBSAFCRKR 2 ай бұрын

Can it disable 4c shocks?

@espenhaugbjrg1770 15 күн бұрын

where did you buy that tool?

@rosuadonis8562 2 ай бұрын

Hi. Can you please make a video about where are the lift points on your xc70 and how to manage that correctly depenting on the type of jack used?

@volvosweden 2 ай бұрын

Will do my best!

@rosuadonis8562 2 ай бұрын

Thank you!@@volvosweden

@hungryboy424 2 ай бұрын

Don not know why but playing this is out of focus, reset all my settings, done security scan ! nothing worked ! I Wanted so much to watch this !

@Kimii99 2 ай бұрын

Wow you have a lot of surface rust with only 132k km. Mine has less but i have 480k km. I have problem with vibration and stuttering from front to back and vise versa from 1000-1200 rpm when driving i any gear doesnt matter. When idling and in N i can feel vibration on the steering wheel and passenger chair is vibration/moving little bit could that be engine mount or trany mount?

@jasper_north 2 ай бұрын

Canadian cars are all rusty. So much salt on the streets 80% of the time.

@volvosweden 2 ай бұрын

Harsh long winters. Also parking the car every night in garage where temperature is warmer and it melts.

@Dalbayob69 2 ай бұрын

Those lower ball joint bolts are proper pain in backside. When I did mine it took me almost 2 h to get one side off and other side bolt snapped and had to drill it out. Off topic but have you thought about installing 2 piston callipers from XC60 or would it not be worth the hassle?

@volvosweden 2 ай бұрын

The ball joint bolt on the passenger side almost broke. Separating was very hard. Been there from day one most likely. Two piston brakes not for me. It works fine just as it is.

@alltiallo 2 ай бұрын

Very good. I also started to get a bearing sound on my V70 D5 AWD and it sounds like its coming from the front. Where can I buy that tool for pressing the bearing in and out?

@volvosweden 2 ай бұрын

We got it on Ebay

@darekkoodziej5852 12 күн бұрын

Chyba używasz bardzo twardych klocków hamulcowych, bo tarcze bardzo zajechane 🙂

@gunnarlandin3258 2 ай бұрын

Skip those dust protectors. They are not needed.

@volvosweden 2 ай бұрын

Feels like true.

@frankbaird9672 2 ай бұрын

How many Km/ miles on your XC70? I have an 07 S80 with 200k miles on it. I like watching your videos & have done several of your jobs. Thx!

@volvosweden 2 ай бұрын

135000 Km at the moment

@JohnGorny 2 ай бұрын

You can also just remove the brake caliper mount with the caliper attached to it, pull it off and slide the caliper over the spring like it's the rotor and zip tie in place. Hope you didn't overpay for that tool, but mine was out of round and needed to be shaved with a dremel in order to use. Despite being a heavy tool, kinda lacking on quality.

@volvosweden 2 ай бұрын

Thx for the tip! The tool was from eBay around 175$ CAD We split the cost with my friend

@JohnGorny 2 ай бұрын

@volvosweden Glad it worked, some places sell that same tool for wild prices $300+

@tejada999 2 ай бұрын

Hello from Spain!! First of all, thank you for the videos. Can you please upload a video on how to change trunk hinges on a 2009 xc70? When I open it it goes down by itself thank you very much!!!

@alexeykazakov1956 2 ай бұрын

Юрий, я бы не стал колотить по шаровой, когда на место ставишь, она итак не в лучшем состоянии. Съёмник ступицы зачотный.

@volvosweden 2 ай бұрын

Буду менять рычаги летом 2025. Если доживем :)

@alexeykazakov1956 2 ай бұрын

@@volvosweden это я понял. Доживём точно. Рычаг-то дотянет, вот шаровая бы на начала стучать в ответ. Особенно при переходах из тепло а холод, и обратно.