Genie G3T-BX Remote control

[@ScottSmith-fp2qs]

Bought two of these for my Overhead Doors; Model: Python 2 to replace the original openers. I followed the instructions and had it programmed within a few minutes. This video really helped! So far I love these...and a great price as well. I will say, these are much smaller than you would think. Very good purchase and I would recommend to anyone with the same door as I have. Through Overhead Door, the original replacement was $49.00 each. I replaced both of my remotes and the total came to approximately $31.50 (which included shipping). They also showed up via USPS within two days from when I received the email confirming the shipment! This was two business days sooner than I expected. I highly recommend!

[@jcalderon76]

HEY GATEHOUSESUPPLIES,,,,THANKS FOR THIS INFO, I JUST BOUGHT THIS CONTROL FOR MY GEANIE PRO SCREW DRIVE MOTOR AND DIDN'T HAVE THE INSTRUCTIONS ON HOW TO PROGRAM THE MOTOR, SO THIS VIDEO DEFINITELY ENABLED ME TO PROGRAM IT AND NOW IT WORKS LIKE A CHARM!

[@boscoe16]

excellent, have old opener and remote and newer remote that came with the house. so after a few years the newer remote stopped working, changed battery and nothing. followed these instruction and working fine. outstanding info, thank you!!!!

[@dgwmd56]

Thank you for sharing! I searched everywhere trying to get my remote to work and finally came across your video. In less than 2 minutes I now have a functioning remote. I’m very grateful

[@pseudonamed3128]

100% agree with the positive comments below. I followed the instruction that came with the unit - no workie. I followed the instruction that came with the remote - no workie. I followed instruction from another KZbin instructional video - no workie. I followed these instructions - workie! Also, some comments on this video state they are having poor range with this remote. I walked a house and a half away and it was still working. Thank you GateHouse Guys!

[@whatwhat720]

My husband and I are out here on a frigid Chicago winter's day programming ours. Glad we came across your video!! Thanks!!

[@nktr4579]

Very easy to follow. Doesn't take long for me to program. I'm a girl and I'm able to make this work by follow these easy instruction then everyone can. Thank you so much.

[@jeanninec.pires-reese3015]

Thanks for this very helpful video! I bought a remote at home depot and there were no instructions. After watching your video I had it working in 10 minutes!

[@4brucru]

Instructions the size of a Thanksgiving plater and still don't help as much as your clip. You turned frustration to success! Thank you!!

[@cxhwang]

Thanks. My key stopped working and because of your video I was able to get it reprogrammed.

[@rngd3441]

You sir are a savior! Had a remote that was working then one day it just quit. Went through your programming and back in business! Thank you!!!

[@BumBee22]

Thank you for sharing. This made my non-working remote work.

[@leroyfarmer]

Thanks for showing how to set the remote to the older systems. Helped me a lot!

[@mikesebbo3448]

Thanks for the video. I didn't realize the remote has to be reprogrammed after replacing the battery.

[@pennyyodice3967]

Thank you for your video! After many frustrating attempts to key up a new remote, your valuable tip on changing it to a series one, finally made our opener work! Very Grateful!

[@wtfrc8908]

Best video out for this product! Thank you!

[@lstrejo48]

Thank you for the easy step by step instructions It worked like a charm.

[@lebrumsmith9160]

This video was very informative and helpful to me. I even took the time to give a review 😂

[@cgstands]

Worked like a charm, great video

[@mofaye38]

Thank you Gatehouse but I too am having a hard time programming a new remote and some old remotes. Someone else installed, previous owners, believe it's the older model so I think I need to clear the learn button as you say BUT will that erase the remotes that do work and our side door pin panel? I'm just wondering how big a job in getting into!

[@cavanfamily12345]

geeeze louise thanks man... im sweating my balls here figuring out how to set this remote... u guys below me are right genie needs to rewrite their instruction manuals....

[@JoyceBlake7]

thanks. my mom is going to be so happy i set it up for her

[@robertsquillace9507]

I accidentally programmed my button 1 to both my doors, is there a way to factory reset the remote as to program it again? Totally want to reset to factory default…

[@eastons22126]

What if you have two of these? We can't figure out how to get both programmed. Do one and it works. Do the other and it works but the first stops. Please help

[@wxbgt01]

Thanks, had it working in a matter of minutes.

[@justaguy4real]

can it learn or copy codes from other remotes like my gate entry key fob remote to community living area?

[@randygatekeeper4297]

No, it can not do that.

[@marionl4620]

Thank you! Great Instructions!

[@patimo6]

Thanks for the video. Made programming my remote fast and easy

[@miguelsantos9606]

Thanks body it works thank you for the video it helped me out

[@SavageLizard]

Worked like a charm, thanks!

[@rachelhobbs1234]

Thank God it works

[@garypalmer3868]

What if your garage door doesn't have a reset or learn button on it? I've looked everywhere and there isn't one.

[@lynluong5291]

Thank you helps a lot! 😁

[@MrCurtis360]

i know this is OLD and all but thank you for your video

[@tommyk6719]

No problem, very easy to understand. Thanks

[@COMMANDOBLACK]

Thank you. The video was very helpful.

[@joecercone1447]

I’m trying to program this remote for a non genie opener. How can I do that?

[@orlandomedina3429]

Can you add a lift master gate opener to the genie remote ?

[@gatehousesupplies]

NO, But you can use a Liftmaster 375UT remote, That will work on a Liftmaster and a Genie system. Check the compatibiity chart to make sure both of your units are covered. gatehousesupplies.com/liftmaster-375ut-new/

[@paulberdy5455]

I follow the steps and the garage door only goes up a few inches....any imput? The opener is a H6000A Genie Intellicode.

[@Yippeekayay.]

Good stuff! My new remote worked on the previous model.

[@justiceelias9237]

You prolly dont give a shit but if you are stoned like me during the covid times you can stream all the new movies and series on instaflixxer. I've been watching with my brother for the last weeks :)

[@averymarcus7245]

@Justice Elias yup, have been watching on InstaFlixxer for since november myself :)

[@solisprime2669]

Thank you. You are the best.

[@naleenichotoo3450]

Could the genie remote works with a liftmater garage door

[@randygatekeeper4297]

No, this remote only works with Genie, The Liftmaster 375Ut will work with Liftmaster and SOME Genie units.

[@jaretthill8475]

this video was very helpful

[@SkyBear0509]

Hi how to go back to green after red ? Thanks

[@megustapapas]

Omg it worked!! Thanks :D

[@alogumaalog]

This ia what im looking for for how many years

[@almightygooch86]

thanks for the info, really grateful for the help!

[@MOESHATX]

Thank you so much for this!! Life saver! 😁😃

[@jvchavez789]

Thank you, you made my day much easier...

[@superbad0415]

Will this remote work for Genie 1/2 HP Screw Drive?

[@gatehousesupplies]

Depends on its age but if it has 9 or 12 switch or its an intelicode then yes

[@racegunz]

Thanks, that was just what I needed to know I wondered why the led's were different colors. Now why is this not in the instructions ????

[@lien302]

I have the G1T-BX (one button remote), how do I increase the range on this remote? I literarily have to stand right up to the garage door to operate it. The range is pathetic. I'm curious if the G3T-BX has the same issues.

[@gatehousesupplies]

First step is to replace the battery then try to reprogram it. Check the antenna wire and make sure it is extended fully, make sure you are not using LED of CFL light bulbs in the opener or nearby. Do you have any other remotes that have better range? It could be a bad receiver board.

[@lien302]

The GateHouse First thing i did was replace the battery. antenna was originally ran down the top part of the long metal arm that holds the threaded shaft, but now I relocated it to run away from any other wires and garage motor housing towards the garage door mounted on the garage ceiling. I also replaced CFL bulbs with outdated incandescent bulbs as you instructed. Now the remote can operate only half the distance of the driveway. So some improvement but still unacceptable. Nothing wrong with the receiver board. I do have other remotes that can operate much much farther. This is the only remote that has very weak signal.

[@gatehousesupplies]

lien302 Given all that then you might just have a bad remote, if you got it from us I am happy to exchange it for you/

[@JP-nk8ol]

I have a model gcg350 , I lost the original remote and ive tried a few new ones. Currently I'm trying this one and it acts like it is connected only the door doesn't open/close when I push button the buttons. I've both red and green. The receiver flashes but nothing happens! Please help! Thank you!

[@JP-nk8ol]

The GateHouse, anyone?

[@mikerivera98]

I have a question. I have an old model gene intellicode and when I tried to re-program the light keeps blinking and do not take the programing

[@edgarjaimes910]

does a genie remote work on a liftmaster??

[@chrisburns4008]

Do you know how to program it with a lift master?

[@gatehousesupplies]

Not compatible with Liftmaster, the 380UT will word on most Genie's and Liftmaster gatehousesupplies.com/liftmaster-380ut-2-button-universal-remote-control/

[@johnnyvaldez9889]

hi got a genie model # G5500 we just moved in this place and we got only one remote. i bought GENIE opener and for some odd reason it dont work did i buy the wrong one?

[@gatehousesupplies]

+Johnny Valdez What is the model number of the remote you bought ?

[@baldomerodelfierro]

thank you! sweet & easy workssss!!!!!!!!!!!!!!

[@thomasd8576]

Thank you so much very helpful

[@ninjawarrior4431]

Thank you so much..! It works..

[@ambermedina1368]

I have a a Genie Model G3T, my battery went out so i replaced it and now i can not get it to work on my garage door. I am looking on the back of my remote but i am not seeing any other model numbers. I have FCC ID: B8Q-315390T and IC: 2133A-315390T .

[@gatehousesupplies]

+Amber Medina Try to reprogram it

[@fordma54]

Awsome, helped a lot.

[@gatehousesupplies]

Hi Tyler, What does it have 9 or 12 code switches?

[@jmarckson88]

Will this remote work with a Stanley D2001 opener?

[@gatehousesupplies]

+jmarckson88 No it will not, sorry

[@NuBeatzNumuzik]

Following the directions that came with the unit was a fail, watching this video made setting it up a breeze therefore. . . Victory!

[@redgixxxer]

Awesome TY!

[@thienngo265]

Can it learning code from another remote ?

[@gatehousesupplies]

No, Sorry it can not.

[@thienngo265]

@@gatehousesupplies thank you 🙏 for reply

[@sheenamartin7712]

how do i no what remote i need for my genie pro screw drive i no its called a master something

[@heatherkerns6109]

You Rock! Thank you!

[@dickjones8746]

Can't get two remotes programmed for the same garage door. Changed one to series 1, then programmed it. Worked fine. Did the same for the second remote. Worked fine. Went back to first remote. Didn't work. Re-programmed it. Worked fine. Went to second remote. Didn't work.

[@gatehousesupplies]

Your system might be full, try to erase all codes by holding down the learn button for 10 seconds. Then repeat programming steps, make sure to only press and release not hold down when programming remotes.

[@bryanhunter2499]

Thank you so much help me so much.

[@ih0nda]

I hold mine for 10 secs then red led turns on but once I let go and push it 3 times it just green unlike in your video it’s red.

[@Tyflea593]

What if my garage door opener doesn't have a button to push?

[@Dillinger86]

will this work with a genie cryptar 2? The Gatehouse

[@gatehousesupplies]

No, it will not that is to old, sorry.

[@Dillinger86]

The GateHouse thanks, I went out and got the GM3T and that doesn't work either.

[@gatehousesupplies]

The GateHouse Its very old you should replace the entire garage door motor for safety reasons. If you do not want to do that then you will need to get a new receiver and remotes we offer an easy to install kit on our site here is a link. www.gatehousesupplies.com/universal-plug-in-receiver-kit-p/365lm-1%20kit.htm

[@ronsanchez4366]

Does it work with the promax2

[@1111winter4w]

Does this work with DIP code?

[@jimjim6089]

+1111winter4w Genie support tells me it will but he didn't mention it or show inside.

[@1111winter4w]

+Jim Jim Yea I was unable to set this up with my unit. I'm not sure how to with the DIP codes.

[@floridawestcoastinspection7329]

Thank you

[@Chuy_0225]

will it work on a genie pro screw drive

[@Kiddro22]

I have the same style. I programmed it but it only goes up using the remote but not down.

[@bigdizzy5954]

Thank you!

[@frayestas]

Thanks man!!!!

[@theanimalmuppet]

Thanks so much!

[@nisarkoshan2675]

Thank u so much

[@ajma417]

Thank you so much!!

[@MrBoots81]

THANK YOU!!!!!!!

[@bruzzer11]

Thanks!

[@Ashes2Ashes_Blush2Blush]

T-T Mine is being a butt..it wont work. Lol the written directions were crazy as well. I'll get it eventually....

[@jamesschmitt7742]

Why do I have to reprogram my remote all the time? It's a pain. I have to crawl through my garage window to get into the garage and reprogram it like every other week.

[@gatehousesupplies]

James, Does this happen with all remotes or do you just have one? I would suggest erasing all codes by holding the learn button down. Then reprogram the remotes, if it happens again and to multiple remotes they most likely the doors receiver board is bad.

[@gatehousesupplies]

Yes if the unit was made after 1997.

[@Katrinius]

Thanks! :)

[@gatehousesupplies]

Genie G3T Remote Control

[@thequeenofresources]

Thank you brother for this video. It was a life saver and if it was not for your video I would have had to call my handyman to come out. But, I was able to use your video and it programmed right away. Thanks a million. Richard and Keshia

[@79taven]

Thank you:-)

[@PuppetierMaster]

It works! IT WORKS! TYTYTYTYTYTYTYTYTYTYTY

[@Iversonwings1]

a little confusing but i got it thanks

[@gatehousesupplies]

They are the same.

[@burdgejosh]

Sounds like Ben Stein

[@spatula6]

Blabber for 2 minutes to show 10 seconds of programming... which doesn't work if your model doesn't have a "learn code" button.

[@sb5839]

Awesome thank you worked

[@theanimalmuppet]

Thanks so much!