gianlucaarenadesign DSO150 battery shell replacement.

a while ago I modiefied the DSO150 from JYETech to add an internal rechargeable battery. My modify was not very easy and you need to modify it before assembling. A few days ago Gian Lucca leave a comment with an ebay link in one of my videos.
He design a new bottom case for the DSO150 that make it so easy to add a battery to the DSO that you can't belive why JYE Tech it didn't do from the beginning.
I got in conntact with him and he send me one case for a review and here it is.
If you have a DSO150 and want a battery inside then go to his ebay page and buy the case it is so easy to modifiy.
ebay gianlucaarenadesign - ebay.to/39WoG4B (new Link 2020)
If you want to support me and the chanel please use the links, when you want something from banggood.com I will get some percent of your revenue.
my patreon page if you want to support me directly.
/ tselectronic
JYE-Tech DSO150 Kit
bit.ly/2xbiVAv
XIAOMI wiha 25 in 1 screwdriver
bit.ly/2wRJ1s3
Aneng AN8008 9999 count multimeter
bit.ly/2vzlcCd
If you want to get the DSO but without the battery, leave a comment and subscribe to my chanel. On march 20. I will pick the winner an send him / her the DSO150 with the case from gianluccaarenadesign.

[@amarjeetsinghbanger2895]

Very nice fitting sir thanks for nice video.

[@karlng2691]

Thanks for the video! Love your content always! You deserved my subscription!

[@standishgeezer]

Really nice modification kit. Interesting video

[@ianallen2]

Yet again, another great video. Great explanation and very good descriptions by yourself. Well done. :)

[@billywhizzy]

Very neat job!

[@englishrupe01]

Good job, and a great upgrade kit! Thanks!

[@englishrupe01]

P.S. Your link to this kit is no longer working, so i gave an updated link in my comment below. Thanks!

[@aimeiz7637]

Graet video, great modification kit. Than You.

[@arifriedman4779]

I watched this video and was so impressed with the little shell kit that I ordered one immediately! I hope that I win so I can pick the one of a kind, complicated unit to compare my build to! Thanks for taking the time to make the video!

[@christophersleath449]

I've just ordered one of these little scopes. I've also come across usb rechargeable 9V batteries on banggood. So the board in the battery does charging from a usb socket and converts the 3.7V from the lipo to 9V. Do you think that this would be useful for the dso150 with a bigger lipo? There's also one wuthering charge indicator LEDs. Might be a simpler mod?

[@arifriedman4779]

I really couldn't say. It really depends on how you will use the scope. Will you be needing it to be highly mobile like out side working on you car and will you it for short tests here and there or constantly on for a long project building session?

[@christophersleath449]

Ari Friedman sorry I meant to post the question in the main thread. I've never done this before and it looks like I mistakenly replied to your comment. Sorry

[@ianallen2]

I would love one of these. So easy to put together.

[@Modellmotorenbaude]

Very nice video! And a very nice shell for the DSO-150. I bought a complete Kit from Gianluca and it was delivered in 6 Days. Everything fits nicely and the build is easy even more after i saw this Video. Btw: The perfect size battery for this shell is the battery from a Galaxy S4 Smartphone. It has 2600mAh and fits perfect in the shell. Nice job, well done!

[@gianlucaarena3995]

Thank you for this fantastic video! I would like to thank Osvaldo Collalti without which the project would not have been born...

[@thsinger]

this case is really great, you thought on every detail while construction it. Thanks again for sending it to me, It was so much fun to build it, and soon someone else will have fun with it let's see where it goes after it's travel from italy to germany and was combined with chinese parts.

[@martinzb1612]

so easy!!! thanks for the vid

[@fdiedrich2517]

Thank you for the video -- it has prompted me to order one of the these kits from gianluca. Even before I've ordered the actual DSO150... hehe.

[@JosefZvolanek]

Super video! :-)

[@flyingdutchman6984]

There is plenty of room inside the case if you eliminate the encoder daughter board. I bend the encoder pins up and solder it directly to the main board. You would need to cut down the two screw posts as well. With the encoder daughter board there is only 4mm height for battery, and after my mod there is 9mm height for battery. By cutting the traces at the on/off switch one side can be repurposed to turn the boost converter on and off eliminating the need for a second switch. It is also fairly simple to modify the original 9v input jack to charge and power the device. Much smaller battery management modules are available, and there are plenty of inductor-less boost converters available if you shop around. Using a 2s 7.4 volt battery is also worth considering for a number of reasons.

[@MkmeOrg]

That is a pretty great little mod! Looks pro. Cheers

[@thsinger]

Thanks, flowers go to gianluca.

[@thsinger]

Congratulation You are the winner of the DSO 150 with gianluccas back case and the battery. Please send me a Message.

[@migacz99]

I am really like your movies, and again excellent youtube video.

[@Btolbert]

Is that a standard JST connector from the switch to the PCB? Does it come with the back shell kit?

[@nevzatgunesdogdu3092]

Thank you for the descriptive video. A very successful upgrade. DSO150 - Shell for battery pack kit is $ 12.90 USD. But the shipping fee is $ 18 USD. A total of $ 30 USD. This is not an acceptable price for me. Thanks again.

[@thsinger]

He send from italy. So it depends where you life how much the sending cost. Just contact him he comment also on this video, maybe there is a cheaper way to send to your country.

[@normdurkin6425]

..nice video

[@HectorAyetCerna]

Very nice video! I know it's a little bit too late to comment about this video but I wonder what happened to the 220uF capacitor and the 1N5819 diode as shown in Gianluna's diagram. Are these components necessary or not? Thank you!

[@TBL_stevennelson]

I looking to learn how to use it. I was hoping it could tell me if the diy power supply I build are putting out clean power. Recently I built many Op amp and amp kits from China. I was hoping to get the dso150 to tell me when it's clipping and get the voltage to calculate the watts. Thanks for the videos. Your a good teacher keep up the good work.

[@jbuszkie]

I just got my case yesterday. The case was not as good quality print as yours. But it still worked for the most part.. I could not get my screws to catch the lid of the DSO. I tried to drill the bottom a little and went two far and drilled right through! so I just used some tape to keep the case together!

[@sherridavis5744]

I did the same with a iPod 4 Touch battery a 3.7 v li ion charger pack charging module and a boost converter didn't have to buy any case would have been better with that case conversion nice

[@thsinger]

The case modification is in another video its more work but also more fun.

[@samscalfano4768]

Great build video. One question though, how do you charge the battery when battery is low? Is a modification to the case necessary to have access to the micro USB plug?

[@thsinger]

Sam Scalfano the case from Gianlucca has an opening for the USB Port so no mod needed.

[@ahmet-balci]

can i check the code of a remote garage door contol with the frequency mode?

[@tonysfun]

Thanks for all that info and the video! What version of the bios/firmware on your small scope? Where did you get it? Stay safe!

[@thsinger]

It was one of the first ones I don’t remember the version. As almost everything I buy it from banggood.

[@alejandroperez5368]

This mod is more expensive than the oscilloscope itself :/ 12.9€ + 3.5€ shipping, +extra money on the battery...that's almost 20€ just to get rid a cable you will have to connect more often than not.

[@thsinger]

Modding is fun, nothing about the price. And without cable where you still need a battery is more versatile. There is another video where I modify the case to place a battery.

[@fharni]

Great tutorial. I ordered direct these parts.

[@thsinger]

Good idea, the DSO150 is one of my favorite kits.

[@fharni]

ts.electronics can you recommend a webshop for good lipo batteries?

[@thsinger]

lipo battery I have are from other stuff, I never bought one.Maybe banggood have some or a shop for RC Modells.

[@ParthBhat]

Thanks for sharing and for giveaway :)

[@patsylandri2066]

I cannot find where to get these parts

[@JaySDunham]

ebay link for case no longer works. Is it still available?

[@alejandrosanchez9127]

Good video, but i have a question, where can i get a LiPo battery just like yours? Or what battery could it fit just fine for the scope?

[@thsinger]

I don't buy those battery's they come from my garbage bin, I'm always looking for broken eletronic stuff and keep parts that I maybe need.

[@bustyouup4free]

Does this work on Etepon version ? Also do you have a link of the battery ?

[@charliehull1326]

Would be great if you can just attach a solar panel or 2 right on the back of a flat cell battery to keep batteries charged almost like the old calculators I think they were low voltage

[@florinbaciu2325]

Hi, i have an dso 150, and stm32 chip heat up, and at a temperature , the display makes white. How i can fix it?

[@thsinger]

B F G Electronics i think this was a Problem with the negative rail parts. Check all the voltages.

[@florinbaciu2325]

ts.electronics and what i need to make to fix it?

[@thsinger]

first check the voltages? Link to the schematics www.jyetech.com/Products/LcdScope/Schematic_150analog.pdf There are not many parts involved in generating the voltages. It's all around the ICL7660 and two voltage regulators for +5V and -5V this is the place where I would start. It's quiet difficult to analyse when you don't have the board on your bench. The 3,3V rail is generated on the digital board www.jyetech.com/Products/LcdScope/Schematic_150main.pdf It's the LM1117-3.3 that generate the voltage check them all. And then go ahead with checking the micro and the other stuff. You should be able to fix it as long as the micro doesn't release the magic smoke.

[@florinbaciu2325]

ts.electronics the voltage of regulator is around 3.29V and on pin 9 of micro is 3.2V, i removed the analogic board, and surprise, the micro still heat up.

[@garybonard9591]

i'm in America and want to buy the upgrade but can't figure out the ebay how can i see in english

[@englishrupe01]

It is here: www.ebay.com/itm/DSO150-Shell-for-battery-pack-/202666253839

[@michael3223]

i waa to get it please

[@Ivan4es1]

The problem is - MT3608 is very noisy on output, and it can affect on oscillocsope. Did you made measurments and compares with working on battery and 3608? My transistor tester working from 3608 - asks for calibration every time I switch him on until he worked from 3608. After put 2x18650 - works fine.

[@thsinger]

For me this is a fun project and so far for the signals I test with it it’s very fine.

[@calidoscopio1515]

Save time go to 6:22....before bla, bla, bla