It's actually a faulty o2 optimizer. By plugging the factory sensor back in your basically eliminating the ability to autotune. Which is fine if you're already tuned to where you want to be. I'm currently going through the same thing and dynojet no longer uses the optimizers. The kits now come with instructions to put a second bung into your exhaust. I'm assuming to eliminate error code issues. I ordered an optimizer off ebay. If that doesn't work I'll be getting another bung welded into my M4
@bikerboy39454 жыл бұрын
Shoulda just removed the seat rather than going through the trouble of removing the coolant reservoir. The instant I saw the cable sleeve I knew exactly where I needed to look lol
@farmfreshsquid10085 жыл бұрын
Hey man been watching your videos for a while this morning with bike wouldn't start. I have no error codes in the fuel pump seems to kick on. I checked all the fuses and connectors the dash lights up but it gives me a high beam and a turn signal indicator and my TST Industries tail light is for some reason yellow now. Hope you have any ideas on what my issues could be thanks in advance
@ACProductions775 жыл бұрын
could be the starter Relay, check to make sure the cables are are secure there and the fuse. you mention that your tail light is lit in a yellow color? does it stay on that way?
@farmfreshsquid10085 жыл бұрын
@@ACProductions77 i checked all fuses and wires. And yes my tail light is yellow I've never seen it that way before.
@ACProductions775 жыл бұрын
@@farmfreshsquid1008 was the tail light wired correctly could be that the tail light wire from your bike is connected with the turn signal wires of the the tst rear light, or it could be a short on the circuit board of the tail light check with tst see if they can send you a replacement.
@farmfreshsquid10085 жыл бұрын
@@ACProductions77 I considered that and went over everything. Its at a shop now. Thanks
@bidhan42 Жыл бұрын
i got 42 instead of 24 and before my speed wasnt showing i fixed my cable and speed is showing but engine light and 42 is still on any solution?
@ACProductions77 Жыл бұрын
42 is associated with speed sensor, clutch switch, and gear position switch, so verify they are operating normally as well. If the ECU sees the bike in gear and clutch engaged = no starter, for example. The ECU should reset when the faults are corrected.
@JamieS19926 жыл бұрын
I have had my PCV since the bike had 200km on it now when it hit 9000km the light came on the O2 sensor is not plugged in the PCV deletes it
@camillecorpuz6 жыл бұрын
what year is your R3? I'm now getting this code after doing a bunch of mods which included a full exhaust. In my application, I plugged the O2 port, and disconnected the sensor from the harness. I have an ECU flash that removes the O2 sensor, but still getting this code.
@ACProductions776 жыл бұрын
Jason Blancas mine is 2015. If you didn’t use a jumper plug for the o2 sensor then the check engine light will come on and u will get the same code 24. Only way to turn off the light will be to remove the led inside the gauge cluster which is way to much work. Most simple way to cover it would be to place small piece of black tape over the check engine light if you planning to keep this setup for a while.
@camillecorpuz6 жыл бұрын
Thanks, mines is also a 2015. I know that the PCV comes with a jumper, so I may look into finding a solution to jump the connector. As an interim, I did plug the sensor back into the harness and the exhaust. The check engine and the error are still present. Guessing some riding around would clear the error? its raining, though, and the bike is no longer street legal at this point. is there another way to clear the error, such as resetting the diagnostic?
@ACProductions776 жыл бұрын
Jason Blancas a ride around the block will clear the code if everything is connected correctly.
@archanan42685 жыл бұрын
my bike is not starting with 1st start , after riding for long and it's ideal rpm is lower than 1500
@jegathessuresh93832 жыл бұрын
Hey man. I just change to full system and done with tuning FID. The enjine light (code24) only come when i ride above 185kmh. After that i stop and turn off engine for 30 mins then start back that light turn off automatically. But the problem is every time i ride above 185kmh the light turn on. Any suggestions?
@ACProductions772 жыл бұрын
you need to get your system tuned on the dyno, do you have a power commander on your bike if no then i suggest getting one or you can get your ecu flashed.
@jegathessuresh93832 жыл бұрын
@@ACProductions77 okay bro. Thanks for the info
@tonxymontana93356 жыл бұрын
HI, i have FULL akrapovic same code 24 getting, what sensor should i order i dont have anyother just bought bike like that, can you send me the link of the new sensor that i can put to remove the code and engine light please.
@ACProductions776 жыл бұрын
the #24 code refers to a bad o2 sensor so you would have to replace the o2 sensor that is made for your motorcycle
@samissa97143 жыл бұрын
hello, i own an 2020 mt 03 and my engine light turned a week ago and wouldnt turn off. i installed an ebay full system exhaust a month and half ago and im not if its because of that. any tips?
@ACProductions773 жыл бұрын
if you installed a full exhaust system on your bike did you install the factory o2 sensor back on or did you cap it off?
@samissa97143 жыл бұрын
@@ACProductions77 I put it back on, but there was no engine light for weeks, and it randomly turned on after I was finnished from work a week ago
@ACProductions773 жыл бұрын
@@samissa9714 besides the check engine light do you also have a code on the gauge cluster?
@ACProductions773 жыл бұрын
@@samissa9714 you may just need to get your bike tuned to the new exhaust system as now the parameters are now different from the stock setup
@briankeith7577 жыл бұрын
I haven't had time to watch the video yet but why would you want to remove the light
@ACProductions777 жыл бұрын
Brian Keith only remove the light if it gives you a code number, not to remove the light completely.
@Bossanovask83 жыл бұрын
I get the light but no code on a r3 2018 any idea?
@ACProductions773 жыл бұрын
it would have to be a defective sensor somewhere, you may have to get your bike serviced
@jayasreebomma30296 жыл бұрын
I don’t get the fuel pump noise when I turn on the ignition??
@ACProductions776 жыл бұрын
check to make sure your kill switch is not in the off position
@JamieS19926 жыл бұрын
you shouldn't get the sound if you stopped the bike with the fuel pump already set
@baecchi41537 жыл бұрын
mine gives me a 19 error code .. and wont start the engine .. what i do is switch the key off then on again .. does the job .. for a while .. then do it all over again ..
@ACProductions777 жыл бұрын
ba ecchi code 19 will be your side stand switch, it could be faulty and need to be replaced.
@baecchi41537 жыл бұрын
AC Productions Philippines r3 ver. dont have sidestand switch ..
@MrQWEEEERTY7 жыл бұрын
ba ecchi dude im having the exact same problem im Filipino aswell have you fixed it ever since?
@baecchi41537 жыл бұрын
Wait a minute opo boss .. sali ka sa r3 group sa fb .. dun ko din nalaman solution .. actually may recall ang yamaha .. papalitan nila wire harness ng susian at papalitan ang tank brackets .. free of charge boss .. hope this help ..
@MrQWEEEERTY7 жыл бұрын
ba ecchi Salamat pre, dadalhin ko sa yamaha to 1.2k kms plng ntatakbo.