GROHE | Pull-Out Hose Replacement | Installation Video

[@ooofest]

This made our replacement of the hose straightforward, thanks. Now, I wish the hose wouldn't have developed a leak after only two years of moderate use . . .

[@johnkoetsier]

Thank you for this. Super-helpful! I had some trouble pushing the new hose up (it was getting stuck on some obstruction about 10" or 25 cm up). So I kept twisting it clockwise and eventually the hose made it past the obstruction. My old system had a spring around the hose ... I guess the new systems have a weight?

[@totsbusiness]

It is very hard to create a short video that explains how to do something easily - great job here - thank you

[@joannabieska6518]

Great video, but it would be helpful if it illustrated how exactly to loosen the coupler from the hose before unthreading - the video cuts to it already being completely loose. The red sticker on the coupler indicates to do this by hand only, but it feels superglued together and because the coloured sleeve spins, it's difficult to get a good grip on it.

[@mariongehlker2618]

I replaced the hose for my Grohe 30306DC0 SuperSteel Eurosmart Pull-Out Spray Kitchen Faucet. Thanks for a great video. However, the hole on the new weights seem to be smaller and I can't get it to close around the hose. Are there different sizes for the weights? The old one had screws, this one a clip.

[@theos6848]

So easy. Do you have a video of doing this with your right angle faucet? I can't seem to get the hose out ..

[@HoraceShaw-r8o]

Our Bridgeford kitchen faucet (part 33 870 apparently) has sprung a leak in the braided hose near the faucet head. We got a replacement through the vendor, Frank Webb Home, but it is coiled metal. Will this work as a replacement and is the process the same as in this video?

[@xiefeng2009]

Great video. I have a ~18 year old Grohe A 112 18 1M 2.2 gpm UPC faucet. The hose is leaking. However, I am not able to pull the hose out of the faucet AFTER disconnecting it from high pressure hose and removing the weight. Feeling like the cobber header (with thread) is not able to go through the faucet. Any idea why ? This is a rarely used faucet as it is located in basement sink.

[@GroheAmerica]

Hello, thank you for contacting us. Can you please email us at [e-mail] and write, "Attention David/Alisha" on the subject line? We'll be happy to assist you. - GROHE Social Team

[@KYLO_JEN]

Hey, any reply on this? Having the same issue.

[@grimmblade]

I had to go underneath and direct the end of the hose through the hole where both sides of the tap go through the counter. it was hanging up.

[@theos6848]

​@@GroheAmericahaving same issue. Any updates? My faucet is a right angle and with hot & cold hoses in there it will not pass through the arm...

[@donnabuttlaire427]

We can not see the quick water coupler for the first hose unscrew because our large sink blocks it. The coupler is pretty high up and not sure I can do it by feel. We need a plumber to come out you think?

[@pjkim2782]

My faucet is Grohe K7. it's neck shape is bent almost 85-90 degree angle. I cannot insert the metal replacement hose (part no: 46174000). Are there any solution?

[@yvesplante3572]

What is the part number for this particular hose. I have the same and looking for a replacement? Thank you.

[@angusmulcahy7946]

I need a 3/8 adapter for my pipe, where can I get one??

[@bif3578]

On mine, the plastic threaded end of the nozzle cracked, where it connects to the hose. Is this a common replacement part, or do I need to order one?

[@paulhunt7883]

What model of faucet is in this video ???

[@VincentYCLin]

I need help on finding the replacement hose, can you please tell me how I can find the part number? I am in Canada

[@GroheAmerica]

Hi Vincent, thank you for contacting us. Can you please email us at [e-mail] and write, "Attention David/Alisha" on the subject line? We'll be happy to assist you. - GROHE Social Team

[@indiegogogirl2662]

I need for Essence. Please post a part number. Thanks

[@mpeg12]

My old hose end gets stuck trying to pull through the faucet, even with some silicone lube. Is there a technique to get it through?

[@GroheAmerica]

Hey! We will need some more information to assist you with fixing your pull out hose issue. Please send an email with a picture of your Grohe faucet and the question to [e-mail] and we will be able to assist you further with instructions.

[@mpeg12]

​@@GroheAmerica Nice! I'll do that next time. This time, pulling up the old hose would get stuck. Some lube got it further. Pushing the end up with a long screwdriver got it past the bend.

[@keykeyscales]

You can also take off the top part of the faucet. The curvy bit. Just wiggle it around a bit while pulling up gently and it should pop off. There's a little metal ledge in the curvy bit that gets it hung up

[@handmadeinportland4125]

@@keykeyscales thank you! Mine wouldn’t feed until I pulled the curvy part off.

[@andyjaske8416]

I have a similar problem. I got the old hose out and took the curvy part off the top, but the new hose won't feed past the on/off tap - seems to be blocked at that point.

[@johnarmstrong1578]

Bought two Grohe Ambi Cosmoplitan taps one of them swivels like we want it but the other is fixed which we don't want, how do I adjust it

[@GroheAmerica]

Hi John, thank you for contacting us. Can you please email us to [e-mail]? Please write "Attention David/Alisha" in subject line. Our consumer connection team members will be happy to assist you. - GROHE Social Team

[@vikasrajput1864]

I have MInta and the hose is leaking after 2 years of use. It feel like poor quality but please tell me where can i buy the replacement?

[@GroheAmerica]

Hi Vikas, thank you for contacting us. Can you please email us at [e-mail] and write, "Attention David/Alisha" on the subject line? We'll be happy to assist you. - GROHE Social Team

[@Nik-ke1qw]

My Grohe Ladylux Zedra Cafe doesn't have a weight... does that matter? It was installed during a kitchen renovation. Thanks! Nicole

[@GROHE]

Hi Nik 150, if the Ladylux Zedra Café you are using has a nylon braided pull out spray hose then it will need the barrel shaped weight. If the hose is metal, then it utilizes a metal spring that should be located on the hose under the sink. Kind regards, your GROHE Social Team

[@TRaddcliff]

I do this....but whoever installed it...made it so tight I can't get it to come thru the pipe under the sink. suggestions?

[@GroheAmerica]

Hello, thank you for your question! For this, there really isn’t a trick to getting the hose to come up through the body of the faucet. You just have to twist and pull until it squeezes by the other lines. - GROHE Social Team.

[@TRaddcliff]

@@GroheAmerica thanks. I had already resorted to that and it worked. I was replacing the old ribbed “metal” hose with the new braided hose. By the way the new braided hose is MUCH better. The coupling is smaller and fits thru the housing better. And the water comes out “textured”, so it doesn’t splash all over the place. The old hose seemed like it offered no airation, came out as a solid stream and would splash everywhere. The new hose is 100% better.

[@jeantom4195]

I have a Grohe Alira kitchen faucet. First the metal coil broke off from the inside of the faucet head and now inner plastic hose has snapped. I can't use my kitchen sink now. I still have my product brochure, but can't find the part number of the replacement hose. Can you help me?

[@GroheAmerica]

Hi Jean, we are sorry to hear this. Can you please DM us at [e-mail]? We will be happy to help assist you. - GROHE Social Team

[@1980benf]

I have a leaky Grohe faucet hose. However I cannot find the part number and cannot find any thing similar in local suppliers. Any idea? Should go ahead and change the whole faucet? On the other note, Grohe is kind of pricy and didn’t expect it would fail in less than 3 years.

[@GroheAmerica]

Hi Ben, can you please email us at [e-mail]. Please include the name or product number of the faucet or an image if possible. On the subject line, please write "Attention Deidrea/Cody." Our consumer connection team will be happy to help you! - GROHE Social Team

[@1980benf]

GROHE America sent an email. Thanks for follow up.

[@GroheAmerica]

@@1980benf Great, if there is anything else we can do to assist you, please let us know. - GROHE Social Team

[@shawnfunstuff]

What's the part number of the replacement pull-out hose? I am struggling to fit the Danco 'universal' hose and adaptors onto a Grohe faucet.

[@GroheAmerica]

Hello, thank you for contacting us. Can you please tell us the model number of your faucet? - GROHE Social Team

[@shawnfunstuff]

@@GroheAmerica Concetto 3134900E Chrome

[@shawnfunstuff]

How can I order it ASAP to Canada?

[@TRaddcliff]

@@shawnfunstuff I've got the same one....its TERRIBLE. the hose is ribbed and gets caught on something. super bad design.

[@razwanfarooq8776]

How can we replace the supply pipes...?

[@GroheAmerica]

Hi Razwan, unfortunately the supply pipes are not replaceable but please feel free to contact us at [e-mail] to get further assistance. - GROHE Social Team

[@rickw6015]

what is the part number of the replacement hose?

[@GROHE]

Hi Rick! In this Video the part used has the number 48 293. Please be aware that we have different hoses with different systems - to ensure you get the right products for your project, please contact your GROHE supplier. Kind regards, Your GROHE Social Team

[@FirstLastOne]

Pretty sure those types of faucets are called pull-down not pull-out.

[@StephenGoldman]

Too bad they don't honor their warranty without a sales receipt??? Like everyone saves every sales receipt for 10 plus years . What about when a plumber installs and does not pass the paper work onto the home owner??? nice fixtures but poor customer service for warranty. Will never purchase their brand again.