Check Engine Light Troubleshooting: Honda Element DTC P0498 P0135 - OBD2 Scanner - Relay Testing

[@alexrichardson9664]

Excellent walkthrough. Helps me continue diagnosing an '06 Element.

[@ChunkBronson]

Thank you so much. You saved me from going fully insane after my cat converter got stolen I still got these codes with a new cat and fresh o2 sensors.

[@Resa_1220]

What was the problem

[@jasonadelaars5699]

Great video! I'm diagnosing the same fault code and all the research I've done your video is by far the most thorough. Thanks for posting!

[@grokshop]

Glad it helped

[@krperry2007]

Tip-You check the fuses continuity with your meter without taking them out since they have the contacts on the top.

[@mikeherte8643]

Great video. Lots of good troubleshooting technique on display - I appreciate it, thanks.

[@surelywoo]

Excellent video. I learned some useful tips. Thank you for posting, and I'll check out your other content.

[@joelpearson8623]

Excellent job! Thanks for the step by step diagnosis.

[@teddy22a]

Really thorough video. Esp describing the wiring diagram aspect. I have the same fault code for the EVAP system. Wish me luck.

[@arcadioaligangajr3591]

Thanks for these information very helpful.totally relieved my stress.

[@user-uk6yz1my8h]

Have a 2004 drivers headlight high beam keeps blowing out. Replaced the electric load detector still same issue

[@HowIsVietnam]

Permit me ask question, my car is Honda accord 2006 with that code EVAP, I replaced canister but didn’t work, I also don’t see check engine light, in this case the light was removed? I just buy it and was cheated, now can not pass inspection. Thanks

[@paquesepas6696]

Is this the same for a 2004 Honda element? Is this relay still behind the glove box? I still have a p0135 after I installed a new oem denso air fuel sensor. Thanks.

[@user-iz7fh6xx7b]

2013 accord lx 2.4l... P0498 code cause was connector came off canister valve..

[@rodneysmith247]

Any comments why after ignition the check engine light blinks 10 times only and goes off with no scanner code or constant check engine on?great 🎥 👍

[@grokshop]

Not sure about your specific case, but I know that in some cars you can get the light to flash the codes such that you don't need a scanner. I seem to recall doing this before and I think I had to short something to get it to blink the pattern. If that is what is going on - you would need to find the pattern decoder & also check for your car if this is even possible & if something could already be shorted without your prior knowledge.

[@carycase5563]

Thanks

[@user-iz7fh6xx7b]

Perfect, thank you. Got lucky, my P0498, only code. Connector came off canister valve..

[@user-iz7fh6xx7b]

2013 accord lx 2.4l

[@user-iz7fh6xx7b]

2013 accord lx 2.4l . P0498 code .. Connector came off the canister valve

[@Samoan_D]

excellent ty great video ..man your a smart guy lol

[@quocthaonguyen741]

Where is your wife now, I haven’t seen her for so long

[@just1doper444]

🤞🏽 0.20 seconds in ;)

[@frankthompson7526]

It would be nice...if the computer could tell you precisely where to look for the problem! No they want you to take it to a mechanic and pay from 300.00 on up! Sucks!

[@octaviocortes3374]

Yea

[@crz7962]

Amigo no me lo creeras pero me diste la solucion mismos codigos crv2013 gracias

[@luisfernandotorresrios6365]

Como lo resolviste amigo? tengo los mismo problemas , ppor favor ayudenmeee D:

[@crz7962]

@@luisfernandotorresrios6365 el rele activa al sensor y a la valvula del canister Compruebe el rele

[@crz7962]

@@luisfernandotorresrios6365 en ni caso era el rele q estaba defuectuoso

[@crz7962]

@@luisfernandotorresrios6365 pero revise q lleguen los voltages y los masas al rele si estubiera bueno