How to replace a tiled-in kitchen sink (No tile repairs needed!)

[@PhoRunner]

Did this for my mama and she’s one happy camper. She got a kraus double sink. My cast iron was held in with 4 tiny nails under the tile. Once I noticed them, it came out no problem. I didn’t go the extra mile and cut the wood and use those obnoxious clips. Just siliconed it in and called it a day. Thanks for the video and idea.

[@stevenhancock5312]

Dan, Thank you so much for posting this helpful and really clear video. My setup was essentially identical to yours, so my wife and I were very happy when we found your video. Our enamel sink was 40 years old and in bad shape but we didn't want to get a new kitchen. We used the same Kraus sink that you did and are really pleased with the result. I can pass on a few lessons learned that might be helpful to someone else doing this. FIRST, I found that using a couple of bottle jacks to help free the old sink from its bed of mortar worked well. It was really stuck but popped free immediately with just a little pressure from the jacks below. SECOND, my tile was on a rather thick bed of mortar, for a total depth of about 2 inches or more, so the supplied bolts were too short. I didn't want to remove a lot of wood, so I bought a kit of the Elkay LK463 bolts. They are expensive but worked. They have a very small head which spins in the Kraus channel, but the hex nuts which they come with are a perfect fit. So I fixed the heads by adding a short plastic spacer to cover the missing threads and then a hex nut which I fastened tightly. I also added some loctite for added security. The kit comes with enough hex nuts to do this, and this worked perfectly. To secure them from below I used a long sleeve 3/8 inch socket. In the final installation, it took just a couple of minutes to fasten the 10 long bolts that I used. I also had a very close side wall on one side of the sink as in the video, and I cut slots like as shown in the video and used two of the supplied Kraus bolts there. I used a router to cut these slots. These two bolts were a big challenge to fasten because of very narrow access space (about 1/2 inch wide and maybe 8 inches deep). The hard part was rotating them 90 degrees after inserting the sink. I eventually got it with the help of a very long screw driver and a long metal ruler. I would recommend cutting these slots with plenty of room to rotate the brackets freely. THIRD, I should have covered the open water lines better, and flushed them out before installing the faucet. I kept my old HansGrohe faucet because it was still working well. When I turned it on there was hardly any flow. I found that it had a small filter at the end which was full of grit from grinding the tile. Everything worked fine after I cleaned out the filter. FINALLY, for someone like me not too familiar with this type of work, I recommend taking your time and carefully thinking through all of the steps. I found it helpful to make practice cuts in tile to get used to controlling the grinder. For the final installation we placed some 2x4's with eyelets in the ends to hold the sink rim just above the caulk so that we could make a final check on clip locations. My wife and I practiced an installation before applying caulk. I used a suction cup to hold and control my end of the sink while lowering it into place, and that worked well. We love the new sink. Thanks again Dan!

[@johngao4534]

Steven, I have to say that you also did a great job as well. I am wondering if it is easy to take out old cast iron sink after you finished tile cut surrounding sink. Dan was lucky to remove old sink easily because his old sink is smaller than his cuts. How about your case? Thanks

[@Gallardo6669]

Thanks so kindly for sharing your ideas

[@kennethsouthard6042]

Very nice work, I especially liked the dust control. My only suggestion would be to install the faucet on the new sink before you drop it in. That way you don't have to deal with getting under the sink later and struggling with a basin wrench.

[@JohnnyBallou]

Yes! Especially us "oldsters" w. back issues!

[@nayy31]

I finally decided to do the same thing after watching your video like 11 times. I made the mistake of cutting the opening just a bit too tight and my old sink was installed on a slight diagonal so it didn't come out easily. Had to lift it out from above with a chain, a car jack, and a piece of 2x4. Ended up popping a few tiles. On the bright side now I learned how to fix tiles, lol. Turned out great. Also, setting up a window fan blowing outwards helped tremendously with the dust control. Thank you so much for showing us how to do it.

[@veroshky]

I so much appreciate the comedy in this video. 😂😂

[@AdiAbhisPapa]

This is a great how-to video. I have similar tiles & sink in my kitchen and had considered several times in last 8yrs to upgrade. I knew that I had to cut the tiles to take the old sink out but wasn't sure how or "brave" enough. This video gives me confidence and I'll be doing it soon. Thank you, Dan.

[@Chris-cj9jn]

I can’t believe how insanely helpful this video is! You’re a godsend. Seriously

[@StayHandy]

Glad it was helpful!

[@firevike2420]

Great video! I was beginning to think I could not replace our MC Hammer era sink without starting a HUGE counter replacement project that would evolve into much much more... I have restored faith in finding a solution to keeping a happy kitchen and home, thanks!

[@lorenrickey5481]

I had the same problem and used my Milwaukee cut off tool with the included diamond wheel. Worked better than I expected. Dropped the new Kohler sink in and done. Thanks for your video!

[@StayHandy]

Glad it worked out!

[@robertaugustine5350]

Big thanks for posting this. I’ve been wanting to remove the old cast iron sink since we moved in 4 years ago, but did not want to try to match the granite tile and grout. Bought some diamond blades for the grinder from Amazon for $15 and had the install done in one Saturday. New sink looks amazing.

[@Rayquesto]

Man... you don't realize how much this is going to save me investing wise. Much much appreciated!

[@sheilaryan1337]

I really like your video. I have a similar sink but what stood out is your calm practical approach of doing this project with many details regarding the trouble shooting in which one needs to prepare for. Thank you!!

[@darioaquino6676]

the video shows from step 1to finish.clearly and detailed procedure how to install the kitchen sink.outstanding tutorial.

[@StayHandy]

Glad it was helpful!

[@venitajelks8856]

I have the same ugly countertops as well as the sink, What a blessing to share this video with my husband, he the same thoughts about the tile around the sink and countertops. Great tips thank you

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@MrBrysta]

I was going to remodel my 50 year ceramic tile counter in my kitchen. But regrouting the old and a new sink makes more $$$ sense today. Thank you for sharing.

[@StayHandy]

You're welcome!

[@yerxiong9938]

Thank you so much! There’s a ton a videos on replacing a kitchen sink but non with a tiled in sink. Mines is exactly like yours and your video will help me tremendously! New sub.

[@RyanRytrades]

As a DIYer, we all learn once the hard way with dust getting everywhere. Needed these tips yesterday, but great video, thank you!

[@Eric_Rides]

THANK YOU so much for this video! We have the same situation and ordered the same Kraus sink. Everything went just like the video. Even the supplied undercounter hardware works (just barely). I thought this was going to be a can of worms but wasn’t at all. Once the corner tiles were cut the sink popped right out with a little wiggling; no cracked tiles. Thanks again!

[@StayHandy]

That’s great to hear. You’re going to love that sink.

[@Johnnie2714]

Thanks for this video. I followed your instructions, bought the same Kraus sink. Came out beautiful.

[@SaragozaD]

Thank you! This was an excellent video! I have an identical setup and I want to replace my sink with, I believe, May be the very same sink (Costco). I have been hesitant to do it b/c a few friends (guys) told me I couldn’t do it and it’s not as easy as I may think. But after seeing your video you have really given me confidence. Thank you!

[@rochellecrews2800]

Thank you so much! This was OUR kitchen, the tile, the old sink, and it helped so much as we replaced it with a stainless steel sink, and yes, we'll replace the tile later, but not now, and this was perfect!

[@timweber3277]

Just had to comment about what a great job you did here on a challenging project 👍; really good work !

[@MrCednumber1]

Good job! So impressed I've subscribed to yoir channel. I'm actually a licenced plumber but have not dealt with removing a tiled in sink but have a customer needing that done. Definitely hoping the available replacement sinks will fit on the old tiles like that. An oscillating mult-tool, with the right blade, would have been much easier in removing the tile instead of the angle grinder. The mult-tool would cause way less to virtually no dust also.

[@megrb8910]

Did you ever try this? How did it go?

[@stevenjocelyn2515]

We are in the process of doing exactly what you did. Your video was easy to watch and informative. Thanks!

[@Ankorthmey]

I had the same tile counter top with the same thickness , I had the same beat up double old sink which my old lady complained, so I bought Krause sink from Costco. Never install the sink before so I searched for video how to install it and found you amazing video. Your video made me look good with my old lady. The only problem I had was I had to run to HD to get a 16" screw drive to tighten the lock screws since they were hard to reach. Thanks so much for this SUPERB video.

[@StayHandy]

That's awesome!

[@johngao4534]

Is that easy to remove your old sink after cut out?

[@merrickm.4295]

You just saved me days of work! Great video and helpful!

[@ForrestKritzer]

I literally have the exact same setup as you on my sink. Old double sink on tile countertops. I purchased the exact same sink that you have in this video. Could you please make a video on how you switched the plumbing from a double sink to a single? It would be SO helpful. Thank you.

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@MerrillMadsen]

Thank you so much for posting this - this is precisely what I needed to learn! Really appreciate all the tips and thorough explanations.

[@badenglish-member9785]

I have exactly the same tiled in sink and it has chips and leaking. I will replace it using your tutorial. Thank you for sharing this video.

[@pure50bliss]

This is very helpful. I have the exact situation. I want to attempt to replace my sink. Didn’t realize I am gonna need the right tools. Hmm. I will need to show your video to my husband and convince him to help me in this project.

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@DaveDurham]

Nice work. I might just do this, thanks

[@GrahamSeward]

Exactly what I needed to know for my own kitchen!

[@ronmcgowan]

Outstanding video! Thanks for taking the time for the rest of us.

[@StayHandy]

You’re welcome!

[@mfplumbing9341]

drilling holes for the sink clips great idea man i could of used that technique plenty of times in my past .. they sell longer ones which i usually use.. but when you don't have em improvisation at its best.

[@vistaglass910]

Awesome video. I replaced mine after watching your video. Huge upgrade for us. Thanks for your help!

[@StayHandy]

I still enjoy my sink! Glad you do as well.

[@voyager619sd]

Very well done video. Covers the possible problems, how to plan in advance to you have the right sink.

[@Rayquesto]

I just did this to my sink. It took me about 5 hours because of my particular condition though and various learning curves with the tools your recommended in this video. I never used them before. Is there a way I can take a video or picture and tag you on instagram or something with those hashtags? This video helped sooooo much. Saved thousands of dollars!!

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@Rayquesto]

@@johngao4534 Yes. The tile clamps down flanges of the under mounted sink. It may not be the case for every under-mounted sink but you’ll most likely find that the flange stick out by about 2 inches. Once you cut the tile, the flanges are no longer clamped and you can remove in general.

[@johngao4534]

@@Rayquesto Thanks so much for your comments. I have a plan to replace my old cast iron sink.

[@johngao4534]

Is the size you cut out exactly same as the size provided by manufacture's cut-out template?

[@Rayquesto]

@@johngao4534 Honestly I warrior weekended it. Didn’t follow the template. I kept trying out if the cut was large enough by making it fit and then if it didn’t I would go back and cut a bit more off.

[@JC-kk7tx]

Great video. I came across this because I was lost on how I could cut my tile to widen the hole needed for my new sink. Great advise. Can[t wait to try it tomorrow.

[@wendysprague3995]

Excellent video! We have a horrible sink that has already been refinished once. The counters and backsplash are granite tile so we don't want to break the tiles

[@StayHandy]

This will be a big upgrade for you then!

[@jngregg]

Very nice, convinced me to hire someone to do this rather than try it myself!

[@kennycetera1522]

jngregg LOL. My exact thought, too.

[@hv2328]

🤣🤣🤣

[@wildndetroit]

😂😂😂

[@Summersoft88]

Hope I can find a plumber who would do it and hope he/ she doesn’t charge an arm or leg.

[@mr.breadNwater]

Thanks a lot for posting this video! It was EXACTLY what I was looking for. I'm in the process of installing my Kraus sink. Your video helped me out big time.

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@mr.breadNwater]

@@johngao4534 removing the sink was fairly simple after cutting the tiles holding it in place, but it was VERY VERY DUSTY! I tried enclosing my kitchen with plastic but when I used the vaccum trick as in this video, the vaccum blew the dust outside the plastic and ended up everywhere in my house.

[@johngao4534]

@@mr.breadNwater You are absolutely right. I just completed it yesterday. I was lucky to easily remove old sink after cutting out the tiles. Thanks for your suggestions. Since I have a very small space, I have to put vac in backyard and use a long vac hose from backyard to kitchen, so I keep vac running for 4 hours to suck the dust from cutting.

[@ColdWarVet607]

Well done. My RA Grinder is my favorite tool of mass destruction, I use it for cutting metal, now its time for tile.! Thanks much!

[@Nobody_Important_Yea]

Outstanding work and production delivery. Thank you!

[@StayHandy]

Much appreciated!

[@DiannaAtherton]

I really like your install. We put in this same sink last summer. Love it.

[@zikmiester]

Great video, I was not sure how to do this but you have given me a strategy I know that I can use - thanks!

[@1972tana]

Thank you, this video helped out and saved me a lot of money. You were very through on your instructions and the tools you used.

[@StayHandy]

You're welcome!

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@miguelmejia8690]

loved it! great job man, nailed it !

[@jenniferbrown5562]

Thanks for all the details and tips this was perfect for our removal and install👍🏾

[@StayHandy]

Thanks for leaving a comment Jennifer. Glad you found it helpful!

[@Gallardo6669]

Thank you. Excellent video, exactly what I needed.- i thought you would use an electric vibrating chisel to remove the tiles. I want to re- use my edge tiles eventually.... Good job

[@handymanjourney]

Great work Dan! Keep it up!

[@juansaldana5331]

Actually we have the same white sink and I'm buying the same you drop in..I have the faucet already... thanks for easy my installation..good video 👍

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@susand495]

Well done. Looks great.

[@Creatingmemorieswithkelly95]

I have the exact set up and have been trying to change the sink. The few contractor I talk to recommended me to change the whole counter which I don’t want to. This is exactly what I needed to see. Thank you so much. Great video. You are very detailed. What size is your sink?

[@johngao4534]

I think that is 33x22

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@Summersoft88]

Thank you for this video…. Exactly what I was looking for…

[@iamdjsluggo]

Wow! That new sink made the old tiles pop! Maybe just regrouping a darker color?

[@Nico-be2up]

My question to you is what type of disk did you use on the angle grinder? Thank you for ur video really appreciate it.

[@aomega123]

Exact counter design that i have. Awesome video! thank you!

[@kellyfranett1638]

I need to install a new white cast iron sink under a existing tile countertop. I'm not handy so I plan on having somebody do it but I'm glad that you seem to think it's something that's possible. I understand it could be expensive but it goes with a vintage house and I want the look. Do you have any tips on what I should look out for with regard to removing the existent tile edges and replacement of the sink? Really enjoyed your video, thanks!

[@StayHandy]

I think you can attempt it and hope that tile doesn’t break in the process, but that’s like doing brain surgery through your butthole.

[@OneHighwayWalker]

This is exactly what I am looking to do in my kitchen. The sink is so old that the chrome has worn away and there's aging copper! Now to find a handyman to do it for me.

[@jasony9950]

Very nice, convinced me to do it myself and learn something… ;) where did you get those extension poles.. and what are they actually called?

[@rubent6382]

Outstanding you demonstrated a well-organized plan and apparently have good work ethic I like it you had concern for dust and debris a lot of DIYer overlook that step. Which brings me to my question what were the poles you use to hold up your dust screen? Telescope painting poles? Definitely will be stealing that from you

[@samuelsanchez9883]

Nice! Thanks for the video. Now I have an idea to do it myself

[@ClarkBeattie14]

Thank you. We have the same countertop except I have an over the counter sink so it should be easier? I'll let your know. Do you know of any way to do an "under the counter mount" with tile such as this?

[@georgieo1000]

This works ! 😊 I did it Looks great.

[@julreallife]

Watching from the start all the way to the end- its funny we have the same and exactly chips on sink:-) me and my husband will save money bu just replacing this sink instead of the whole tiles. Thanks alot

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@0_mikaele_0]

What size cabinet did you have?

[@ssergeant9682]

not sure how to install our ss sink which will be replacing our old cast iron sink. the sink fits well into the 2 layers of 3/4" plywood. we had to replace the top layer of plywood. but the clips? that's where we're stuck. plus we do have some uneven spots - can we just use the silicone and install it with just that. perhaps weight it down by filling the sinks with water to help adhere it into the silicone? thanks for your help. this is our 4th day - no sink. no dishwasher because that drains thru the sink drains.

[@tomcatris]

First of, thank you for this video! I have the same sink that my wife and I are looking to replace. Secondly, I know this video’s old, but I’m hoping to still get some answers (from anybody, really). How big is the sink in your video? The only sink size that’ll work to cover the old hole is 33” x 22”. My issue is that my cabinet size is 33.5 maximum. All the 33x22 sink has a minimum cabinet size of 36”. Am I missing something here? Do I need to tear down the walls of the kitchen cabinet so the sink could drop in? Or do I need to keep looking at different brands and see if I eventually run in to one? Thanks!

[@annvetrano5538]

Can this be done with a bathroom sink ?(old tiled in from 1959) I would not be putting stainless in because it’s a bathroom. Advice much appreciated!

[@farzadhamid7357]

Hi Dan, thank you for the video. I have a question,,, where from did you purchase those adjustable bars for covering the dust area and to hang the sheets with.

[@leosreglazingreglazing1950]

where do you buy those dust cloth bars?

[@matthewalkman386]

Can you tell me that faucet and hoses that are used here? I need that exact thing for my sink!

[@clydeford7296]

Thank you very much Dan I have the same setup with a tiled in sink, your video is 5 star informative! thanks for making this tutorial , Dan what did you use to make the hole for the soap dispenser

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@Eric_Rides]

Looks like he used a large step drill bit. A hole saw for SS would also work.

[@komalraut]

Would it be ok to to drop-in/overmount a heavy steel sink over granite overhang??

[@JohanSalvattore]

Well… this was helpful! After watching this video I can now call my sister and tell her I wont be changing her old sink.

[@leslie201168]

thank you so much for the video👍👍👍👍

[@camposfamily9169]

What is the model of that new sink?

[@MariaCruz-xp7vn]

Thank you! Awesome job 😊

[@StayHandy]

You’re welcome!

[@donmack7403]

I have the same in tile sink which is 33 in so i assume that the new sink is more than 33 in wide? i can buy a steel sink in the range of $100 but there always 33 in if the old sink is also 33 in i cant easly use a drop in the same size. what was the size of your new sink?

[@StayHandy]

Whatever sink you buy needs to be wider than the hole you cut to remove the old sink. So yes, this sink was slightly wider.

[@Lee1982i]

Thanks for your video very very very helpful!

[@petethehandyman9185]

Nice work sir

[@achu717]

I wonder how many diamond discs did you have to use to cut out the tile? It burns out fast.

[@winterdesert1]

I just did this on a much more difficult level. My old cast iron sink was at least 80 lbs. Also my new stainless steel dropped down onto the wood ledges (after numerous adjustments) and then I replaced those quarter round tiles around the edges along with corner pieces. Yes you can still order them. I used silicone adhesive to get them to stick to the edges and stainless steel and then used silicone caulk to fill in the gaps. Like you I didn't want to spend $10,000's for a remodel.

[@StayHandy]

Did it work out well?

[@winterdesert1]

@@StayHandy Yes thanks for asking. I think ultimately I would have liked a white porcelain sink, but finding a lip to set down in the wood and then the exact size for those tile is next to impossible with that type. More choices with stainless. My sink tile layout is exactly like yours. Home built in 1953!

[@MrBalloy]

I have the exact same kitchen tile can you explain to me why you would go through all that work and not replace that old tile that I’m thinking of replacing the granite or is there something to it that I’m missing

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@lhughescca]

Great video!

[@briancoakley1524]

Did you measure to see what size of new you would need? If you did, did you just measure the width from tile to tile?

[@cooperdog9956]

This is exactly what I needed!!! Thank you so much for sharing!

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@sterlinghearth6672]

Hey Dan! What kind of cargo bars are you using to hold up your drop cloth?

[@StayHandy]

I don't remember the brand. I just picked the ones up they had at my local Home Depot.

[@drumtwo4seven]

Nice 👍 Thanks for sharing

[@StayHandy]

Thanks for watching

[@lifeisbeautiful7496]

Nice! I was exactly looking for this idea!

[@johngao4534]

Is that easy to remove your old sink after cut out tiles?

[@lifeisbeautiful7496]

@@johngao4534 yes it is easy to remove. But you might need someones help because it heavy.

[@johngao4534]

@@lifeisbeautiful7496 Thanks for quick response. Is the size you cut out exactly same as the size provided by manufacture's cut-out template?

[@lifeisbeautiful7496]

@@johngao4534 I cut exactly same as the size of old one to take it out first. The cut size was smaller than the new one's cut-out template. Then I was trying to drop in the new one and kept cutting a little by little to adjust it. I went trial and error method as I'm not professional. You have to make sure the one you are buying must cover your total cut.

[@johngao4534]

@@lifeisbeautiful7496 I was lucky to easily remove old sink after cutting out the tiles. I cut tiles 1/4" larger than Kraus template because I was really worry about my cutting skill. Thanks for your suggestions. Since I have a very small space, I have to put vac in backyard and use a long vac hose from backyard to kitchen, so I keep vac running outside for 4 hours to suck the dust from cutting. I should purchase Kraus 's air gap, but I forgot it. I had to buy one from home depot. That is a junk.

[@johngao4534]

Hi Dan, I would like to know how could you do if the old cast iron sink is larger than your cuts. You cannot enlarge the cuts because it will not fix new sink. Thanks

[@StayHandy]

You'll have to cut through the sink itself, which if it's cast iron, will be challenging. I would try to find a bigger sink that would allow me to cut the whole big enough to remove the old sink.

[@johngao4534]

​@@StayHandy I was lucky to easily remove old sink after cutting out the tiles. Thanks so much for your video and quick response. If I realized that you posted this wonderful video in 2019, I should complete it early. It is really and big help to me.

[@MariaLuciaGomezGreenberg]

Masterful! Great job--thank you!

[@yeseniadesantiago3018]

Hello my tile broke where can I find one I search and no luck

[@dennisalvarez2518]

Nice job 😜!

[@GhostRooter661]

When you took your measurements did you measure from the end of the compartment or the lip? It looks great I have a similar project coming up.

[@kennycetera1522]

Josh's Juicy BBQ And Outdoor Cooking ... wondering if you received a reply. I haven’t seen a response.

[@GhostRooter661]

@@kennycetera1522 I have not received a response.

[@timcaldwell4126]

Great video-thanks for sharing your info with me-

[@DonTwizzlestix]

Much appreciated, my mother has the same exact setup. I just hope she didn't buy another undermount sink..

[@mayaemsden7514]

WOuld this work with a porcelain farmhouse sink? Trying to find images of what that would even look like (porcelain farmhouse sink installed in (under? over?) pre-existing tile. Anyone have images/info on that?

[@MarkDParker]

A very good video! Thanks...

[@juanloza3451]

This is a great video but you can install the faucet and the drain part of the garbage disposal before so you don’t have to struggle under the sink.