Homemade WASTE OIL STOVE for Workshop !?

[@rmax5150]

New subscriber here. Well done sir! Also, very comforting to see somebody with enough intelligence to understand when to use a respirator. I see soooo many "scholastically challenged" KZbinrs taking no such precautions because they obviously have NO idea what materials they're messing with and what they are breathing in. Sadly, they will find out the wrong way if they continue doing so, even on a semi-regular basis. Especially these "urban explorers" who I've seen uploading videos in which they are literally walking through trails of fallen asbestos from old overhead pipes in abandoned tunnels, etc. No respirators or other protective gear while kicking up & breathing in all that asbestos dust that will eventually kill them in an untimely manner. Sadly most of the people sacrificing their health and/or lives for "clicks" typically appear to be only in their 20's or so. Point being, if your going to start dipping your dumb toes into any kind of new venture, at least take the time to study and learn about the potential hazards associated with any given material and/or era in which a structure or object was produced, so you can mitigate that risk.

[@dougbas3980]

You are the best! So great to watch you work! I am a poor welder and really appreciate your skills. Just found your channel and subscribed immediately. You are an inspiration.

[@UNITED_STATES_OF_AMERICAU.S.A]

I heard you have oil

[@playedbyear998]

knock knock

[@johnmarsden7687]

He needs democracy

[@edo12310]

We can build a d355a faster than you can send people Dare !

[@RandomRobloxuser-mx6xi]

I burned it all sorry 😢

[@royroyson2655]

🤣🤣

[@gattonpc]

Skip to 7:55 for the actual building start...untill then is a tablet marketing.

[@cheezeball6109]

One recomendation i think would be great is to add a inline fan that would suck ambient air from outside instead of the air in the heated space....

[@paulfrost8952]

Why is it better to suck ambient air from outside instead of the ambient air from inside?

[@connormarsh2535]

The intake air is burned and expelled. You dont want to pull in your warm air from inside and push it outside. Use outside air supply to fuel/oxygen for your heat.

[@brianbeck3894]

Everyone should have one like this. no oil problems and the air would be clean. I live in a house with 10 rooms so I make one for each room

[@stefanandjelkovic5350]

Zagadjenje 100%. Ja sam napravio za moju garazu malo drugaciji sistem ujutru sam je ubacio i u 12 sati sam je izbacio. Drva su zakon

[@robertmailhos8159]

Nice looking set of home made vehicle ramps nice to see you making a heater for your shop doctor d.s

[@1979gmcummmins]

I'm going to build one but add more of a down ward slope to the oil feed line to keep from build up and then feed the oil line through the blower tube as to help pull the oil from the tip of the oil feed cause they can build up with soot in a short time. Good build though

[@bentheguru4986]

Not buring clean. Air into combustion pan, setup for rotation and use the incoming airflow to cool the pan outer edges, keep heat in the centre/bottom of pan. Oil feed best dropped from height into the pan away from flame as it will likely burn oil in feed tube and carbonise blocking it. Final advice for anyone building these, all combustian gasses need to be exhausted outside. Waste engine oil contains a lot of nasties to humans and burning it indoors releases these back into the air. Example: We used to have a commercial unit buring our waste aircraft engine oil, I remember all the yellow deposites that would form around the hot air vents until I relaised what they were. The very same yellow deposits I would have to wash off the underside of the engine cowles near exhuast or blast off spark plugs. It was Lead and we in the workshop were breathing that Lead from the oil.

[@bencrosbie]

That's a very long ad for a tablet

[@mrsunyofficial]

Awesome work and inventions

[@tony4metallicaify]

You did a beautiful job! I think I am going build one now!

[@stevangubik6668]

Odlicna pec na preradjeno ulje👌Dao si mi super ideju,da i ja napravim tako nesto za radionicu👍Veliki pozz za tebe,Doctore👋

[@drzejan_nudrik8393]

If you want the use of the stove to be better, add a water drip with which you will feed small drops of water into the oil feeder during combustion. You'll thank you when you don't have to clean such a stove from dirt :)

[@sabby05]

a small sight glass on the side would be helpful to know oil level. over all nice build

[@grzegorzj.3329]

I haven't started watching it yet and I already like it 😅

[@МаксимКулемин-р1б]

Масло не успевает нагреваться, как итог плохое сгорание, трубу нужно сверху внутри камеры сгорания проводить прогретое масло будет давать больше тепла и лучше сгорать, да и кстати закрывать такой котёл нужно герметично чтобы пары сгоревшего масла не нападали в помещение, для того и ставиться вентилятор принудительной тяги😂

[@mambatta]

Build us one please all these numpties commenting on here with there negativities is killing me well done doc

[@CurtisEgan-m7s]

Best oil stove design....but you should use external air for combustion....Easy modify...thanks for the video

[@Ryantoews-xl2mf]

very nice for the winter!

[@BerfuZekiye]

tomorrow's matches any insider tips from you guys would be gold right now

[@tankabbot22]

Just started making mine! Love it!! Where are you located?? Thanks man!❤

[@BuzbyWuzby]

I would add a support between the floor and the two horizontal pipes (air & oil) but apart from that, excellent! PS: It is now illegal to burn waste oil here in the UK, partly for the 'environmental issues' but mostly because the government can't tax it! 🤣

[@Jamie_c74]

Never bothered me lol

[@raymondpomfret4214]

Its already been taxed till the hilt

[@nutmeg9005]

Only illegal if you get caught friend.

[@davidwright1653]

Because as we all know the more tax revenue the government gets, the more likely the environment will be saved. NOT!!!

[@janisvidzs7149]

Nice! Recommendation make shield where oil flow in pipe, to prevent water from entering in oil.

[@boosted_2j]

Wow. Look at that. A tablet woth features that every other tablet has. Wooow ooooo weeee.

[@Hood_Tyme_Fab]

Nice work,i need to build one,ive been saving up waste oil haha

[@arthurcutaiar9994]

Stove video, not a commercial for a tablet

[@SSingh-nr8qz]

Its how people pay for the video production.

[@hardpeak2584]

Браво момче! Сјајно одрађено!

[@ep2560]

in germany not allowed in private homes . And for good reasons . Look at the color of the flame . Not hot enough for a clean and effectiv burning .

[@alexbiss9544]

you are not supposed to put it in your house it contains chemicals it is a workshop stove.

[@georgianbroadcaster4700]

Who cares

[@gazunkafonegazunkafone3492]

Germans burn lignite ffs, literally the worst form of fuel possible for emissions! Also banned i the rest of europe…but you guys ignore that!😂

[@Florin76]

The oil pipe that feed the burner must have 1° slope and I suggest you put the faucet as much as possible at the bottom of the oil tank so you can burn it all. You need also a purge valve at the oil tank bottom so you can clean oil residues that deposit at the bottom. You can cut the upper lid of the burner and mason some thermal bricks inside to store more heat. Well, you can improve a lot :)

[@TheNinja691]

Have you got a video of your build?

[@Florin76]

@@TheNinja691 I didn't think to burn wasted oil until seeing this video, having a working model on which you can improve is great!

[@donalfinn4205]

Well done!👏🇨🇮🇵🇸

[@hartleyhubbard3827]

"...the pipes will serve as legs for..." well, we saw that coming! Sorry, I had to move on - too much time spent on the tablet commercial. Greg [garden grove, CA usa]

[@metaframe2k]

When it flares up, you can add a little water along with the oil, the effect will be like that of a jet engine. The main thing is that the stove does not melt.

[@nemanjadjordjevic2562]

Druze svaka cast za ideju samo pazi da ne updnes u problem sa zakonom👍👍👍

[@vladim473]

Привет!🤝интересно получилось,лайк!такого вида печи я делал на дизельном топливе.теперь нужно в нее сварить теплообменник и сделать водяное отопление в мастерской.

[@meytv5691]

не повторяйте глупого доктора.

[@vladim473]

@@meytv5691 ну может сейчас время конечно другое,а в 90х,начале 2000х такие печи очень даже были в ходу ,их и без принудительного поддува делали,правда розжигать дольше,пока не начнет воздух засасывать.

[@vladim473]

@@meytv5691 конечно такая сейчас мне лично не нужна,газ,либо электро котлы сейчас в ходу

[@MetalStrength-]

Very nice job, keep going ❤

[@s.b2240]

Well as i have ordinary sense, rather than make hole iinfront side u may use think glass it makes more atteacting/ seal packed and also avoid the burning fuel smell

[@alimasters4473]

Мне кажется что подача масла и воздуха должны вместе регулироваться. Подойдет перистальтический насос с редукторным мотором. А регулировать напряжение одновременно на воздушную турбину и насос для масла. 😅

[@old-trucks-nd-Coffee]

Very very neat! Keep up the good work.

[@Duckys_world__]

Awsome video I have built a few oil burners and they put off just as much heat as my wood stove and if you a car guy easy way to get rid of used oil

[@marcoroa8223]

Emite contaminación por humo.?

[@dahlmasen3084]

In worst way possible for the environment😂

[@dahlmasen3084]

@@marcoroa8223of course it does, wouldn’t recommend breathing it in

[@dalespringerwilson4233]

Doesn't burn clean until it's up to temp, made several of them over the years. Smells like ass until you get it up to a good combustion temperature, and that stock pot won't last long !

[@saidmeku707]

how about if you replace the stock pot with something like well designed clay pot used for cooking will it able to withstand the usage for long?

[@wrenchmantooly5169]

I've made one. Working on another one. Air and oil control are very important. I installed a needle valve in my first one. Will again on my second one. My first one worked really well. Oil control was adjustable down to a hair stream. Only trouble was when I sent it to the weld shop the guy that took my instructions was a young welder and didn't understand how flues measured and installed too small a pipe. So I had to run at a hotter tempt to vent well

[@geo2cv6tron14]

Really really interesting and really really cool 🤩👍

[@Jigsofficial16]

Wow that's awesome 💯

[@luisalbertom.r6378]

Eres mi ídolo !!!❤❤

[@percival23]

I would love to see how more efficient a waste oil stove would be if it was attached to a sand battery. At least 100 lbs of sand stored in a metal enclosure attached to a sidewall of the stove. After 4 or so hours, that sand battery should be close to 400 degrees and last for hours after the stove is out. It could cut the oil use in half. But I would to see a real world test of this.

[@matus158]

one little tip - you did all "hair" seals (plumbing hemp) in opposite direction :)

[@MygpbluKaa]

В более менее герметичном помещении, воздуходувка создает пониженное давление воздуха в помещении и повышение внутри камеры сгорания. При негерметичной камере сгорания это создаст круговорот помещение - воздуходувка - камера сгорания - помещение, постепенно наполнив воздух продуктами горения и выжжет кислород чем убьет людей в помещении. При герметичной камере сгорания это вызовет быстрый выброс теплового воздуха в дымоход (он не успеет отдать тепло) и засос холодного воздуха в помещения сквозь щели в стенах/окнах/полу/потолке, что даст низкий КПД обогрева.

[@stephenjose1472]

need to put a brake rotor (disc) above burner to extract more heat , its all going out the chimney

[@croexcavator]

Odlična, korisna ideja. Vrlo dobar edit 👌💥👊 Pozz iz OS 😊

[@DShomemade]

❤️

[@jenyjek5055]

would be a great idea to implement some kind of water line in the otherwise unused top part of the fire chamber - to squeeze some more efficienty out of it. Great idea tho. much appreciation 👍

[@vukcevicmarko6542]

Postoji urbana legenda koja kaže da je Doctor D S odgovorio na komentar 😂😂😂😂😂😂😂😂😂😂😂😂

[@DShomemade]

😂😂

[@danieldaniel-qr1my]

amazing the first video witout stupid voices and straight to the point !!! love it

[@hamidsanavifiroozi5274]

well done very practical

[@onegreenev]

What is the grease and fiber you used to seal the joints of the pipes?

[@berykent4598]

Podrska za bracu hrvate. Pozdrav iz Crne Gore.

[@tobycanales1062]

mine runs about 900 degs. had to put bricks between it and the wall

[@MarjanZuza]

Diko..odlicno..my croatian ❤️💙🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🇭🇷🇭🇷🇭🇷🇭🇷🇭🇷

[@PP.EKOTECH]

Dobra robota ! :) Good job !!! :)

[@DylanHickson1]

What did you do with the saw blade on the pipe threads before adding thread sealant for final assembly?

[@wimpletzers3411]

Roughening the thread for the hair (raffia) does not twist

[@karpiuhp]

just add a couple of 1" or 1 1/4" pipes at the top and connect them together. plus a circulation pump and 2 radiators and substantial heat.

[@borkoniBG]

Bravo komšija svaka ti čast. Odlična ideja i sjajan video, još kada bi znao to sve da napravim haha, ali bitno da je tebi toplo i da ćeš udobno praviti nove ideje a mi uživati u tome. Pozdrav iz Srbije

[@coppermountainstudios3312]

So how long will this run off the used oil if filled up? I like the idea but how long will it run?

[@tanonedekov1138]

I dont know about your laws, but in most places of the world they will give you a insane fine for this stove. Burning waste oil a lot of times is a very poluting process. Some years ago i built a oil heater but i had tons of problems and judging only by the looks of your i doubt it will work,first you have a huge burning camera(the pot)which will melt when it goes to temperature, but this will never happen because this blower is far too small for the camera.I used old diesel fuel injectors to spray the oil like a mist and the it was burning 100% but i still got thick smoke

[@pewpeww556]

Smoke is a by product of incomplete combustion

[@ragibtufek]

Kao jedan od najvećih fanova javljam se za udomljavanje tableta ako već nije udomljen😂

[@DShomemade]

Hehe udomljen je već kod mene 😂😂

[@ragibtufek]

@@DShomemade auuu....za dlaku je bio moj😂😂😂....

[@shanemorgan12345]

Very nice. The only problem I could see is the air pipe not being sealed at the bottom. If the oil burn pot gets a hole or a leak it’ll burn out the bottom onto the floor.

[@TheSiLq]

My only concern is that cooking pot, the metal is too thin, will burn through eventually

[@bimerev]

odlična peć . Imam orginalnu na staro ulje i super je to što sve sagorijeva. Jedino ti dozator na tu pipu nije baš nešto.. Moja ima nekakav rotirajući mehanizam koji gura to ulje i promjenom broja okretaja se regulira tok .. To može grijat tako jako da pocrveni. Stavi još neki ventilator po tome da puše . Bolje će grijat . Samo ne prejak da ne smeta snimanju. JA ne mogu snimat kad moja radi . I da , stavi još jednu tavicu na čemu će gorjet koju ćeš moći lako izvadit van zbog čišćenja .

[@DShomemade]

Da, Hvala ti 😁 Pipa mi je bila najjeftinija, a da je najlakše rukovanje i doziranje 😅 Da budem još jedan ventilator stavio...😉

[@bimerev]

Probaj onaj dozator za infuziju uzet, koji regulira kapanje infuzije. Mada najvjerojatnije neće raditi kako treba jer je ulje gusto. Al da bi kojim slučajem radilo bilo bi odlično rješenje

[@TB-id6wo]

awesome!!! thank you for sharing this video great job!!

[@wrwarnerhall]

Good work, what fan did you use?

[@DShomemade]

80W Aliexpress 😅

[@DjukaWZMechanicGamingComedy]

Postavio sam klip moje peci na preradjeno ulje za centralno grejanje, napljuvali me kao zagadjivaca, kao u evropi to nemoze, evo vidis da moze 😂😂😂 Pozdrav iz Srbije.

[@DShomemade]

😂Pozz

[@nawafalkhader6542]

You are a struggling man and appreciate your beautiful work, and I loved that, and I'm just like you, I have great ideas, and I subscribed to the channel again, and I'm from Syria, and I love that work. Do you use car burnt oil?

[@DShomemade]

Thank you very much, that is the oil from the car.

[@joshuatremper5026]

An the good thing is, oil burns for a long time, so good for overnight burns.

[@dimitrisbek6109]

very nice work.. but i would try to upgrate with closing the combustion chamber and create 4 exhaust pipes heating the inside walls

[@MikeJones-wp2mw]

Use 3 legs and not 4 and you don't have to level the stove out to keep it from rocking on uneven flooring.

[@ГригорийКусков-е2х]

Вентель подачи надо было ниже приварить масло неполностью попадёт в горелку 😊👍

[@LowOctaneMotorsports]

Do you have a link for the intake air blower with controller?

[@tomazk2638]

Super je vais m'en fabriquer un aussi 👌🔥

[@tommyx8925]

Jetzt noch eine Wasserspirale mit eingebaut und schon hat man Warmwasser.

[@cabmanist]

Did you use normal carbon wire to weld that to stainless?? Just learning here but i didnt know it was possible

[@torbjornnostdal2999]

It works just fine👍

[@jozsefszenasi8691]

Can it work with used cooking oil as well? Sunflower oil actually...

[@nedudki]

California, here I come ! :)

[@edg1703]

great job!! where did you get the blower?

[@ingokuhn4192]

Wenn das die Grünen sehen kriegen die einen Kollabs😁😁

[@danielgoodkat2379]

Eigentlich jeder weil das konstrukt blödsinn ist

[@arvedblohm693]

# TEAM MELONEEEEEEEE !,!!!!!!!!!!

[@karelmarx8899]

f..k the greens

[@mihovilmajcen2833]

Dali bi to moglo funkcionirat da se slozi na drva...mislim da li bi grijalo garazu 5x4

[@labradoodle5097]

Nice job!

[@Baard2000]

Customer: why are oil change intervals 4 times shorter??? Mechanic: just to be sure .... ( inside brain of mechanic : 😈😁🤣👍👍)

[@-o-The-Duke-o-]

Mechanic's thoughts : It's looking to be a cold winter

[@MarceloDurán-d6k]

Muy buena la idea pero se paso para ahcer publicidad que no venia al caso, de hacer la estufa. Si haces publicidad que sea un poco mas disimulada

[@samuelfellows6923]

😠 ~ had to skip ⏭

[@JohnDoe-gi2nr]

What to do with used oil to pollute as much as possible? the answer in this video.

[@AbsolutionArmament]

There are off the shelf options with pollute less than wood burning stoves and in their overall scheme more environmentally friendly. As long as you are the person who has the waste oil or can source it locally.

[@Josh-ew1le]

The feet on the legs are a nice touch

[@olivermain5078]

That BMW is ❤

[@DavidParker-cf2km]

A Mercedes.

[@ivanraz]

Don't waste your time. Actually this clip is a commercial for a tablet...

[@ЮрийКим-г4х]

холод заходит, тепло выходит😂

[@christophe-r5n]

Pas mal ! 👏 Pare compte...si il n'y a pas de courant de 220/24/12...Volts, pour alimentation turbine 🤔??? ...ont fait comment...🤔??? Nous sommes pas complètement autonome 🤔 Triangle pyrotechnique = combustible + air + étincelle = 🔥

[@rynasitrakarakotondrabehar787]

Were did you buy the fan?

[@kresimirmilisa5560]

Very good😊

[@gt40f]

You forgot the fire test for the tablet.

[@kekibro3086]

Super videooo Davide

[@aleksanderbye5917]

Great job, but you should suck air from outside, so that you dont remove the hot air from inside your workshop. 😄

[@RakTheGoose]

heat rises, and this being on the floor will remove the cold air from the workshop floor

[@aleksanderbye5917]

@@RakTheGoose the hot air from the stove will circulate the air, simply by heating it. No need to use inside air to get circulation 😁

[@branchandfoundry560]

My thoughts exactly. Has to be makeup/supply air from somewhere when exhausting to outside. I wonder what net gain is, setup as shown. Not knocking, honestly curious about the numbers...sorry, I'm a nerd & love numbers!

[@peterkn2]

But the air outside is heavily polluted from burning motor oil 😂

[@Suavache]

Dùng dầu nhớt thải làm chất đốt để sưởi ấm và cách chế tạo lò rất tuyệt vời