Honda CFR250X Carburetor removal | DIY Repair | FULL Disassemble and Reassemble

[@johnB-fj8eq]

Bikes sat too long in my box trailer! Bad gas and wont start!! What a pain to remove these carbs!!! Thank you for taking the time to show people the proper way to remove and replace these carbs!!

[@houseoutoforder]

Hugley helpful thank you for all the detail. It was my first time doing the carb and I wouldn't have gotten too far without this video.

[@primalcarnage2480]

dont need to do that mate just take out bottom bolts and losen the top it will lift up then tighten the top ones the half frame will stay in place ,when ya done losen the screws drop it back down put bottom bolts in ..ya dont need to take full frame off just take bottom nuts out and losen top ones and lift it then tighten to hold in place while you work,the frame will hold in place lifted up

[@senderoverland]

Is there a video on this?

[@quantumtechcrypto7080]

Yes look into smog delete or rejetting vids.

[@Nick-cy1dj]

2 hours job that could have been 10 minutes

[@joeybergeron376]

Looks like a nice little project I got into

[@justinworley3251]

Helped a lot ! Seemed to easy to get out with the video! Thanks

[@muchyandik7259]

I have a 2008 CRF 250R...my problem is the magnetic spool...how many turns on the spool...and how many mm of wire...thank you

[@davidkris]

This is so helpful. It deserves way more view and likes. Thanks for doing this. I subscribed just to support your channel whatever else you cover.

[@ebonics85]

Thank you for the vid! Hope I can get the air boot on tomorrow!

[@joeybergeron376]

Just got done pulling mine man what was Hondas engineers thinking.

[@hellomynameiskyle8129]

Quality video. Just wish it wasn’t sped up so much because some parts were hard to see as it is.

[@patc.5872]

Hi, do you know what size are the vent hoses that come out of the carb? Is it 3mm or 4mm? Thanks,

[@Bobby82568]

Hello there, question for you since you are well versed in Honda CRF’s. I have a 04 that idles fine and sitting it will throttle up fine however when I kick it in gear and try to take off it will bog down really bad and almost shut off. I checked the accelerator diaphragm which seems ok, any suggestions on what to check next? Thanks 🙏, great videos btw they are a huge help.

[@joeybergeron376]

Great video just bought an 06 250x qnd it's dumping gas as soon as the gas is turned on

[@codyevans8133]

Needle and seat is stuck. Tap the carb with a screw driver and it might stop the leak

[@jaredharlin428]

Thank you! I just bought a Honda 2001 cr250r and it had bad gas so I cleaned out the tank and removed the plastic too and, it was a bitch to remove the carb. Thanks man

[@cevansinz]

Good lord. Step 1.) disassemble 75% of bike. Step 2.) remove carburetor.

[@sebertspestsolutions]

Noticing this myself.....just paid a shop$400 to clean carb tank fuel filter etc......still not running right asked them if they disassembled the bike to get it out kid who did work happened to be right there and was like no we just flushed it out! I am so pissed bout to just do it myself this way 😡😩

[@cevansinz]

@@sebertspestsolutions - That is appalling. But yeah, I'm going to try that at home first. Drown it in Sea Foam and see if I can get 'er goin'.

[@dantevitale3455]

Great video. thanks for the help.

[@nickgagnon6309]

I’m having trouble putting the throttle cables back on

[@tarungonneea4614]

Good luck. It’s an absolute disaster putting them on. I’d recommend that you stop. Wait a bit until you have the patience to do it again. And use the smallest wrenches you can to try and get the the cables back on.

[@tunabananer9199]

I can’t even get them off

[@quantumtechcrypto7080]

Engineering…”but you’ll have to remove everything to get to the carb…No they’ll have to” Problem solved.

[@andrewscriven2741]

This is insanity

[@jshenbdjwla1463]

Totally skipped the throttle cables.

[@СергейАнатольевич-н3п]

а я думал у меня трудно снять)))