We're stoked to share the installation guide for 2016-2017 (non Adventure Sports) Honda Africa Twin 1000 pannier racks installation guide. Europe: europe.outbackmotortek.com/pr... USA: usshop.outbackmotortek.com/pr...
Пікірлер: 12
@dalediese4 жыл бұрын
Just installed the x-frames on a 2018 base model Africa Twin (not ATAS). Just wanted to highlight no instructions exist for this. The process is completely different from the ATAS and the 2016-17 models. If you guys haven't done it on a 2018 base model yet, feel free to reach out and I'll run through the differences with you. The rear rack and fender have been redesigned compared to the 2016-17 models.
@Outbackmotortek4 жыл бұрын
dalediese I truly appreciate your comment and your offer on helping us out but we have video installation guide for 2018-2019 standard model: kzbin.info/www/bejne/i5XYf4efeM-feJY I’m sorry you’ve missed.
@PatrickBarkerII2 жыл бұрын
I'm in the process of installing these on a 2017 AT. The parts used under the seat in the video appear to be different than the parts I received. I received all the parts shown in the written instructions on the OM website. I'm at a loss as to where the large washer and M8 lock nuts come from.
@Outbackmotortek2 жыл бұрын
Thanks for your comment. It’d be helpful if you sent us a photo of the brackets that you received. We can advise immediately after. info at outbackmotortek dot com
@danielabramzon78064 жыл бұрын
How wide are these racks for the 2017 AT. How much do they weigh?
@alpha93154 жыл бұрын
Hello. Can I install givi Trekker Outback on this carrier? This sentence used Google translation. I'm sorry if I made a mistake in the grammar. From Japan.
@michaelpfister35724 жыл бұрын
How much clearance is between rack and chain guard? Does a Rotopax fit on the inside of the rack?
@Outbackmotortek4 жыл бұрын
Michael Pfister yes, a 1 gallon Rotopax fuel can fit on the inside
@michaelpfister35724 жыл бұрын
@@Outbackmotortek Thanks for the information. Looks like a well-tought-out rack 👍
@gocanux154 жыл бұрын
@@Outbackmotortek Can a Camel tank fit? I'd like to switch to your racks but I have a camel tank that I'd like to keep. Can do some of the custom mounting work. How far out does the rack sit? How far back and down does the bottom cross brace live?
@MattChurchleyАй бұрын
This video is 20 minutes long and never once shows the rack from the exhaust side. I want to see what kind of clearance there is around the muffler how wide it is and how far it sticks out on one side versus the other.
@BadDadio Жыл бұрын
Tools: * Drill * 1/4” drill bit * 7/8” spade bit (used in place of 22mm drill bit) * 13 mm combination wrench * 8mm Allen * 1/4” ratchet * 3/8” ratchet * 4” x 3/8” extension Sockets: * 8mm x 1/4” * 10mm x 3/8” * 12mm x 3/8” * 13mm x 3/8” Installation: 1. Remove seat 2. Remove fixed seat - 10mm socket, 4” extension 3. Remove rear subframe mounting bolts & discard - 12mm socket, 4” extension 4. Remove rear foot pegs top bolt completely and loosen the other bolt and swing foot peg bracket out of the way Mount crossbar: 5. Drill 22mm holes for spacer - Use 1/4” bit from the top to drill pilot hole - Use 7/8” (22.22mm) spade bit to drill spacer hole from the bottom 6. Loosely thread 80mm bolts through cross frame, spacers and into subframe - 14mm socket, 4” extension 7. Attach lock nuts finger tight 8. Mount left bracket into subframe - Use blue Locktite on threads 8. Attach front top-left rack to bracket with M8 x 30mm bolt, washer, & locknut - 13mm combo, 10mm socket, 4” extension 9. Attach rear top-right rack to cross brace using 6mm diameter bolt, washer, and locknut - 8mm socket, 10mm socket, 4” extension - Cross brace goes on top - Leave bracket loose 10. Attach rack to foot leg mount (8mm Allen) 11. Install right rack 12. Install cross brace with 6mm diameter bolts 13. Snug all blots 14. Tighten all bolts