Honda Element FULL Install Stereo Backup Camera CarPlay. SJoyBring Double Din DIY

Рет қаралды 17,026

Күн бұрын

#hondaelement #hondaelementcarplay #carplay #hondaelementstereo #installstereo #installcarplay #installbackupcamera #diystereoinstall #hondacarplay #hondainstall #sjoybriing
This Honda Element install was time consuming but not difficult. Of course, the hardest part is installing the back up camera. That took some effort. But in the end, it was all worth it. I now have CarPlay, which mean I have a good GPS navigation system in my old Honda Element. I also have a back up camera. YAY! The head unit was really inexpensive, and seems to be working well.
I didn't know I had a factory amp on my car. If I knew, I would have bought a new harness and used RCA audio jacks. Oh well.... I guess I can do that later.
Rear Panel Removal Video • Remove Inside Rear Sid...
S Joy Bring Double Din CarPlay Stereo amzn.to/3MWOFz2
$40 OFF Code:SJB40
Didn't know until later that I had an amp, but this is the harness if you have an amp
amzn.to/3MZQFGX
Standard stereo harness (the one I "thought" I had) amzn.to/3t0vuxo
Wire nut connectors amzn.to/41E7HQO
Butt Connectors amzn.to/3NHLzPQ
Wire End Connectors amzn.to/3veqczb
Crimper and Stripper Tool amzn.to/48gmDqU

Пікірлер: 55

@mrunop 9 ай бұрын

Any updates

@GearGadgetExperiments 9 ай бұрын

It has been working well. My only complaint is that when in radio mode, if a txt comes in, it switches to CarPlay mode for the txt, but does not automatically switch back to radio mode. No big deal if you are not a radio fan. But I am old and prefer radio over stream. Haha

@gsteigerlilly 8 ай бұрын

I just got an old Element and have never done a car project. This video gives me hope I can actually do it!

@GearGadgetExperiments 8 ай бұрын

It is not hard to, you can do it!

@Bluesidian 10 ай бұрын

OMG thank you SOOOOOO much for this Video!! i bought one just like this and had no idea how i was going to install it. Now i know!!

@GearGadgetExperiments 10 ай бұрын

Happy to help

@DennisDural 7 ай бұрын

Thank you so much! I bought this same one a few years ago but never had time to install it. I set up the harness already so hopefully I can just pop it in and pray I can get the steering wheel controls working. Thank you again! What would we do without KZbin!!! If it ever got shutdown the world would go into panic!!! Ha! Ha! No seriously!

@GearGadgetExperiments 7 ай бұрын

Happy to help. I get tons of info from KZbin myself. Good to know I am also contributing!

@digitalbobby42 3 ай бұрын

Thanks a lot, your video gave me the confidence to do this upgrade on my Honda element and now I'm really happy and I saved $200 in installation fees! Now I got to buy the controller for the steering wheel controls. Go Team Honda!

@GearGadgetExperiments 3 ай бұрын

Happy to help

@digitalbobby42 3 ай бұрын

Thanks for making the video, I appreciate the links for the head unit and harness. I'm happy with the results so far. Got to install the back up camera next.

@timuhler8121 5 ай бұрын

Nicely done, you really kept your cool through all that. You are a very patient and knowledgeable person.

@GearGadgetExperiments 5 ай бұрын

Thanks!

@brandonnickerson3077 9 ай бұрын

Amazing video! Thanks for taking the time to make this.

@GearGadgetExperiments 9 ай бұрын

Glad it was helpful!

@djwdeaf Ай бұрын

I put this brand head unit in my element. No issues, works great

@GearGadgetExperiments Ай бұрын

Glad to hear!

@LCLj73 4 ай бұрын

Great video I feel like I can do it myself now all 👍🏾but the back up camera

@GearGadgetExperiments 4 ай бұрын

I bet you can do the back up too! Just give yourself time

@ElPresidenteBuzzard Ай бұрын

The person that goes in here next is going to have a hell of a laugh.

@ibdribbles7128 3 ай бұрын

There’s a problem with the 2011 Element…no rubber gasket around the license plate light, hard plastic. So had to drill small hole to either L or R of mount to the license plate light then threaded it through. Not much accessibility but had to trim back casing to get red power line connected and used the multi wire ground connection. Instead of crawling underneath, I went up the door then into and above the speedometer then right over to the PURPLE/WHITE wire with the RED WIRE and T-connector. Went down to the floor and pulled off the sub woofer cover to find the GREEN/ORANGE wire that the LIGHT GREEN parking brake wire connects to…did another T-connector. Turned the key and everything worked, started and shifted into reverse on my Pioneer DMH-W2770NEX

@marcomartinez1540 4 ай бұрын

Thank you sir

@c0uchsl0uch 2 ай бұрын

Do you know what the output voltage is? Should be anywhere from 2v to 5v out

@GearGadgetExperiments 2 ай бұрын

Sorry, I don't know

@didiermejia780 10 ай бұрын

Same!!!

@lilzywer8421 5 ай бұрын

Do you know why my speakers won’t work whenever I have the wires all connected all the right way ? And my speakers do work

@GearGadgetExperiments 5 ай бұрын

I bet your car has an amp that needs to be powered on. If you watch my video, you will see that I also realized that I had an amp that I needed to power on.

@JCVerseTv 5 ай бұрын

The fit on 37:10 looks different than ( radio bezel slightly overhanging over top plastic) when you were tightening the 4 bolts earlier. Can you advise how you mounted it in? I can't quite seem to duplicate that. Thanks

@GearGadgetExperiments 5 ай бұрын

I had to tinker with the mounting bolt location a few times to get what I wanted. I have the unit sitting through the bezel, not flush with it at all

@ibdribbles7128 3 ай бұрын

Do you know if this unit is XM/Sirius ready or do I have to get another adapter module to connect to the radio?

@GearGadgetExperiments 3 ай бұрын

Sorry, I don't know. I don't use XM

@NikTheRichard 8 ай бұрын

Did you have to do anything to set up the backup cam? Or did it automatically work when you put it in reverse? I have the same radio (face, wiring, instructions booklet) just a differently branded but can't get my cam to come on. Obviously I may have wired it wrong or the connection didn't take but just curious

@GearGadgetExperiments 8 ай бұрын

If you watch the video, you will see that I needed to use the reverse (corrected) light connection.

@NikTheRichard 8 ай бұрын

Thanks for the quick reply. Where in the video did you use that? I swear I've watched it multiple times and didn't see anything with brake lights or brake light connection lol are you referring to that brown wire on the back of the harness? Or the actual brake light? Cause I saw you tap into the reverse light. This is my first time ever doing anything like this. Thank you for any help!

@GearGadgetExperiments 8 ай бұрын

So sorry. I did write brake light. I meant reverse light. Haha

@NikTheRichard 8 ай бұрын

Haha ok yes I saw that. Tried to do that but didn't work. I'll try redoing the wires tomorrow. Too many hours trying today! Thanks for your help and video

@GearGadgetExperiments 8 ай бұрын

That reverse light signal acts as a "remote" to tell you unit to switch screen display to the rear camera. Test that line to make sure it is ~12v when the car is in reverse. Otherwise, your head unit will not know to switch displays. Good luck. Good night.

@sydneybennett5362 6 ай бұрын

sorry i’m a complete newbie how exactly do you tap into the reverse light? let me edit myself. how exactly do you tap that black wire into the ground thing?

@GearGadgetExperiments 6 ай бұрын

buy something like this amzn.to/3x7tmpy. Crimp it on the reverse wire to tap into it. For ground, you can connect to bare metal on your car frame (chassis). Your whole car frame is ground.

@GearGadgetExperiments 6 ай бұрын

Oops. I clicked remove, instead of reply on you previous post about connecting the ground. That is just a bolt that I unscrewed and connected the ground to. No taping.

@sydneybennett5362 6 ай бұрын

@@GearGadgetExperiments oh gotcha okay thanks so much your video is super helpful! and thank you for responding so quick!

@sydneybennett5362 6 ай бұрын

@@GearGadgetExperimentshey sorry just another quick question how did you connect the wire to that screw? did you use like a crimp connector? or just screw it on tight enough so that the wire was compressed between the bolt and panel?

@GearGadgetExperiments 6 ай бұрын

@@sydneybennett5362 remove bolt with socket wrench or crescent wrench. use ring terminal like this amzn.to/49h0Lvq, then srew bolt back in. Or you can just tap into any one of those wires connect to the chassis with the tap connector link I sent earlier.