Hope this helps you troubleshoot your hot tub pump problems! And be sure to check out our hot tub care course at www.swimuniversity.com/spa and use the promo code VIDEO for 10% off.
@bmontano71 Жыл бұрын
Great videos. I have a MAAX Spa 471 b model. It’s about 6 years old. The place I purchased the tub is no longer in business. My spa has a dedicated seat where a sequencer was added to mimic a shiatsu message with water jets. I would press pump 2 on the display twice to activate it. Last week it stopped working. When I press pump 2 I only get water flowing out of the jets pointed at my neck and shoulders and very little water coming out of the jets pointed at my back and no water flow coming out of the jets pointing at my hips or lower back. When I press pump 2 a second time the flow does increase on my neck and shoulders and very little on the jets pointing at my upper back but still nothing coming out of the lower jets and the sequencer is not turning on as it is supposed to. There is a diverter knob valve that diverts flow from that specific seat to my feet and to a seat that is adjacent to it. The adjacent seat and the feet work fine when I divert the flow to them. I tried manipulating the airflow knobs and opening the specific jets to full flow but still not getting any resolution for the lower jets on that seat or getting the sequencer to work again. I clean and drain my spa every 4 months with spa purge and I replace my filters at that time as well. For the past 2 years I have been using the easy frog system to keep my water balanced and clean. The only major repair came last year I had to replace pump 1 and the entire circuit board because of a faulty relay got stuck and burned up pump one. But everything had been working good until last week. Any ideas on why my sequencer and lower pumps on that specific seat not working? Any ideas would be greatly appreciated, Thanks
@KellyFalcone3 жыл бұрын
So, for problem #5, thanks for sharing suggestions if the display isn’t turning on, however, what might be the issue if the display IS working but the pump is not?
@shanonearls69452 жыл бұрын
Did you figure out your issue ?. In having the same issue
@KellyFalcone2 жыл бұрын
@@shanonearls6945 yes! Turns out one of our breakers went bad so the spa was getting enough power to turn on the display, but not enough power to turn on the pump. We realized the breaker box was getting full power from the main, but the output was low and then checked each breaker to figure out the culprit.
@michaelanderson99149 ай бұрын
Thank you. Still trying to get the time machine part to work. 😅
@kirchner1978Ай бұрын
I used fix a leak in my spa, and now my pump isn't working. It's clicking like it wants to, but nothing is happening. I've unplugged, and plugged back in. Still nothing. I'm so upset as I've just replaced the pump 2 1/2 years ago. It's an Aqua-flo pump and I have a freeflow plug and play spa. Please help. 🙏
@richardchauvin29962 жыл бұрын
I have constant loud grumbling sound instead of the regular hum. What could be causing this and is there an easy solution ? Jacuzzi hot tub.
@octaviomartinez293511 ай бұрын
are there Jacuzzis that will not power on the pump, till water is sensed ?
@glennr99139 ай бұрын
My tub has an intermit leak. It seems to lose water when the outside temperature drops. It holds water pretty well in warm weather. I think it must have frozen once, but not sure.
@maryannemccarrick46932 жыл бұрын
Hi Our motor tries to start then stops
@homeroserrano38653 жыл бұрын
How about relays, how do we test those?
@dlucic30089 ай бұрын
I got excited when I heard about problem 5 but it’s not exactly the same issue mine has. My brand new pump doesn’t turn on but I have power to the thermostat. Backstory. Hot tub started Over Heating, so we got a new computer. That fixed the issue, couple months later pump wasn’t running. We ordered a new one but the new one is not running ither, I have to see if maybe I broke a fuse in the computer and if so that would be a simple fix but I have power running because the thermostat and lights all turn on but the pump doesn’t. Hoping maybe you could give me some tips! Thanksgiving
@SimplyChrist Жыл бұрын
My pump is doing strange things. The breaker tripped due to a power outage. When I reset it, the pump comes on periodically on its own and pushes water nicely. So I assume it's not a pump issue. However, I can't turn the jets on with the control panel. The circulation pump works as well as everything else on the control panel. Any ideas?
@georgehurley81945 ай бұрын
Hello, I have a new Vita spa Envie Installed last week, and I only have one level set on pump one so it only has low setting, not the high setting like when you press pump two twice. Anything I should look for in general?
@claudiamarlow5265 Жыл бұрын
I have a tropic seas spa two filter set up. Instruction manual says I should be able to push the light button during initial priming to start the circulation pump but it’s not turning on and the heater just keeps getting hot and overheats because of it and I have to reset everything. Any ideas as to why my circulation pump won’t turn on ?
@dancapen8408 Жыл бұрын
The coupling nut is broke on PVC fitting for pump to tub how do I replace
@juanechapman59872 жыл бұрын
The information is helpful but does not address the issue I am having. My pump will not turn off and the digital panel is not displaying ANYTHING at all. Not even the standard info. Help
@Ryanblake863 жыл бұрын
Okay this didnt exactly help me out a lot. I have power to the display, when i go to turn on jets, it CLICKS but nothing else. No humming, nothing at all, just click. I purged the pump, there was no air at all. The tub is about 3 months old with not a lot of use. Any idea?
@KellyFalcone3 жыл бұрын
Came here to ask the same question! Pump is not turning on or priming, but the display is on and I hear the clicking. So, seems it isn’t a power issue. Need help! :)
@everardolopez62773 жыл бұрын
@@KellyFalcone Hi, I have the same problem, do you get the problem fix yet?
@everardolopez62773 жыл бұрын
Hi, do you find out what was it yet? I got the same issue
@KellyFalcone3 жыл бұрын
@@everardolopez6277 yes! It turned out that my breaker went bad. So it was only sending 110 power and not 220, so the display worked, but the pump didn’t. Replaced the breaker at my sub panel and it works again. My spa guy showed me how breakers can go bad if the connections aren’t really tight and he was able to jiggle it around. I could see some blackness around the wire connector in the breaker where it went bad.
@sjanowski12 жыл бұрын
mine does same. i figured its the pump. clicks but nada. mine runs on 110v so now ill check voltage but doubt its my issue. i found bolts rusted and housing corroded so water damage i presume. i dissassembled and heater side seals are shot too so ordering new ones before i reassemble and test. Doheny had my pump for 12 year old spa and shipped 2 days for free. ill comeback later in week with results.
@Natechasse Жыл бұрын
My breaker trips from the pump, it will run for 20-30mins then the pump trips the breaker and top side control screen is dead. Then I turn it off then back on and it does the same thing. ??
@joefriday95011 ай бұрын
Great video. Thanks
@LaneyaWiles Жыл бұрын
We bought a brand new water pump, installed it and still nothing... what else could it be? Power goes to the lights, and we stopped a buzzing that came from the contactor. Help!
@FluidVision2 жыл бұрын
Power works and jets work. Jets do not work on low and will not heat up now. What could be the problem?
@williamcotsifas17832 жыл бұрын
I can’t find the flow sensor
@jonveenis42242 жыл бұрын
Some flow sensors are built into the spa pack.
@baroquemanagement6276 Жыл бұрын
Hi Great vide! We have a problem that you haven’t touched on and you may be able to help? The jet pump works but has now started running for only 4 mins not 20. It restarts ok but again only for around 4 minutes Any ideas what it could be?
@stephenmoia24412 жыл бұрын
Do I have to empty out my tub of all the water to replace the circulating pump it’s a Jacuzzi 300 series
@marcelomoil38412 жыл бұрын
The brand new pump run for a dia now only humming check voltage and only get 120v in one phase switch speed get 120 on the other phase and still humming
@amandacruse55342 жыл бұрын
Hi what can u do when ur hot tub pump say E5 on the display pump.
@swedishkev3 жыл бұрын
Hi there, mate,I have a balboa control unit, And the flow was not working as strong as it should. I thought it was the pump, The jet button when pressing started to stop working and just become to have a mind of its own. I notice once the pump started without pressing any button and once just stopped also. So because I was not getting much flow, first bought a new impellor, because the other one was destroyed. Did not solve the problem, still low flow. Now I have installed a new pump, And the same problem. So there was nothing wrong with the original pump. Now I installed the new pump today, normally it goes on PR for about 7 minutes then it all starts up normally. So when I put the breakers on, the pump was running on low speed, Straight away, that was strange, never done that before when PR is starting up the on process but is a new pump. The jet button stopped working again with a clicking sound coming from the Balboa control box. Could this just be a fuse problem, possibly. or a relay ,what does a relay look like ? I am dumbfounded here. So now it is not the pump or capacitor, all new so , ruled out. The heating element is all fine and working, all checked there.I have a video ,if you were interested to look at.
@gregackerman88732 жыл бұрын
Kevin did you ever find out the issue with your spa motor? We are having the same as issue as you were with our Balboa spa pump. Wondering if this is a power issue? Every time we have a power outage or turn off the breaker, our pump will not start up on its own again.
@elchuloe12 жыл бұрын
Question my hot tube comes on but don't stay on and there is no hot water
@randyschreiner780711 ай бұрын
One other thing you should add is the failure of the pump to start due to a failed capacitor. This is definitely a do it your selfer fix that only costs about 15.
@nicholeragusa6522 жыл бұрын
Okay so problem #5, but even after resting the breaker doesn't flip has power, the plug gets power but still nothing on the hot tub.
@pauldenham8653 Жыл бұрын
Allso the pump control buttons could be dodgy
@anthony75573 жыл бұрын
Can I use a Intex sand filter pump on a inground pool
@carriemacgregor26013 жыл бұрын
Absolutely not
@tomcaviar76513 жыл бұрын
The spa works then it shuts down. The pump feels really hot.
@robertwashburn17683 жыл бұрын
My most common pump problem is a plastic impeller that swells until it jams against the casing. Pump does not run, may or may not kick the breaker. Spa company answer - replace the motor and pump for $550. Motor shop replaces the impeller $95. Repeat about every five years.
@SwimUniversity3 жыл бұрын
That's some great DIY problem-solving and money-saving!
@dartagnantaft59183 жыл бұрын
What would cause my pump to not turn off?
@justinlindsey41992 жыл бұрын
Control Panel
@go43842 жыл бұрын
Did not address my problem - pumps work but are weak.
@armandodelatorre67553 жыл бұрын
My hi pump for jets is not working, what can I do
@armandodelatorre67553 жыл бұрын
The red light at the control for hi pump is not on but the pump is working as it cycles
@SuperScottschannel Жыл бұрын
😊
@jeffsolinger5671 Жыл бұрын
Well watching this was one way to waste six minutes of my life