How Cool can Transmission Bypass Cooler Reduce Transmission Fluid Temperature Ford Ranger Mazda BT50

[@lenstar01]

Another great job installing that Transmission By-Pass Cooler. The owner will see a big improvement now.👌👍

[@YepThatsIt]

thanks & cheers 🔧

[@FuManchu5ltr]

Brilliant. I really enjoy your videos and most of all your presentation of the problem solving process.

[@YepThatsIt]

thanks & cheers 🔧

[@wahyuwicaksono1133]

thanks for that video....very helpfull for me after installing atf cooler in chevy captiva diesel 2.0 2011...

[@YepThatsIt]

glad helped. you can install an inline trans filter in cooling line, just make sure you confirm the direction of flow as these filters need to be in correct flow direction. thanks & cheers

[@DoubtingThomas333]

EGR in that thing will be full of solid oil and crud, same with the intake manifold. ProVent 200 or RCC351K (or model that could be available specifically for this vehicle from Ryco) is the fix in the meantime, after the EGR valve has been pulled out and cleaned + checked to make sure it's working correctly. 99% of the time they just need a clean and then the electrical connector resistance checked for spec. I've pulled apart several intake manifolds on diesels with just 100k clocked and they are full of solid material, unbelievable...yet totally prevented with a properly designed catch can (I only recommended the two companies I mentioned).

[@YepThatsIt]

hi, try using a better low soot engine oil and a catch can will help keep oil vapour from circulating as well. cheers

[@DoubtingThomas333]

@@YepThatsIt I use c1 or c4 engine oils with DPF equipped vehicles. EGR is very high even at idle in diesels, 50% at idle is normal, this is just an inherent design thing.

[@alexanderstefanxandraswedi5835]

Good job

[@YepThatsIt]

thanks & cheers 🔧

[@DoubtingThomas333]

A bottle of Lucas transmission stop slip/fix will add a lot more heat tolerance to the transmission too. Just FYI. Every little bit helps.

[@YepThatsIt]

hi, we have used lubegard products for years and the quality has proven itself many times. cheers 🔧

[@konducta3095]

Really wish manufacturers would put coolers on as stock for cars capable of towing....really a joke they think a heat exchanger is going to work.

[@YepThatsIt]

hi, heat exchangers are designed to warm up your trans fluid quicker so the rubber seals dont scrub out in sub-zero temps. many people think they are a cooler. its best to bypass completely and add a trans cooler, eliminates chance of getting coolant in your trans too. cheers

[@jrm163]

@@YepThatsIt you’re knowledgeable!

[@konducta3095]

How do you rate lubegards transmission flush? considering it eventually for a flush on a BA falcon with 174xxx km and refill with tq 95.

[@DoubtingThomas333]

The best flush is fluid changes more often. I also add a bottle of Lucas transmission fix every fluid change. There are a few good products on the market, but that's the usual one I buy. Anyway, lubeguard products are good too.

[@YepThatsIt]

hi, unless you have heaps of metallic swarf and/or coolant in your trans, just changing the amount of fluid that comes out when you do a service is enough to boost the trans fluid properties. if you add magnets to the pan, this is a better option to help keep really fine magnetic debris ( that is smaller than the filter element ) out of circulation. often when a trans is high mileage/heavy duty use, by doing a full flush can make it operate worse - this is because older broken down fluid is often thicker than new fluid, so will pass easier through any internal pressure leaks. a trans bypass cooler will also help trans fluid stay cooler and thicker for longer. hope that makes sense cheers

[@konducta3095]

@@YepThatsIt Many thanks as always.

[@Elguapo93]

Fg xr6 turbo ute. Would you recommend an aftermarket PWR heat exchanger or an external trans cooler and get rid of heat exchanger all together? Cheers.

[@YepThatsIt]

hi, we always recommend get rid of heat exchanger and installing a bypass transmission oil cooler. cheers

[@amateurcarpist5474]

Sir, appreciate for your time again. I got a question. If I change the cooler with a bigger one should I put more fluid into the tranny or not? I mean shoul the level be the same on the dipstick as it has been before?

[@YepThatsIt]

hi, yes if the capacity is increased you will need to add fluid...always wise to check the fluid level according to manufacturers recommendations and according to required temp. cheers

[@martynohara8101]

Hi. Can you tell me where you guys are located please? I'm in hemmant, Brisbane

[@YepThatsIt]

hi, north east country victoria. best to contact via our facebook link in description. cheers

[@martynohara8101]

@@YepThatsIt thank you

[@velintamutiarany6070]

Sir i need your help do you know code push belt for mazda demio 2008? Cvt transmision.. Thx

[@YepThatsIt]

hi, if you are in australia we can sell to you. cheers

[@closertothetruth9209]

i hate the coolant thermostats for transmission water coolant some seem way to high temp, i always bin them and go full oil to air.

[@YepThatsIt]

hi hate is such a strong word......in Oz we dont need them to help warm up trans temp quicker, so here we get rid of them to help eliminate chance of getting coolant in with the trans fluid and cool better. cheers

[@closertothetruth9209]

@@YepThatsIt mine runs at 55°c has done for years no issues but is that temp a little low.

[@YepThatsIt]

@@closertothetruth9209 is that scan temp or pan temp? torque converter temp will be higher anyway

[@closertothetruth9209]

@@YepThatsIt cooler temp using a lazer temp gun

[@abushamma7732]

Hello , need your help please, yesterday my car Ford Galaxy 2011, 2l, 140 hp, diesel, automatic transmission power shift, I switch to D, can drive normally, if I switch to R, nothing happens even if I accelerate , nothing happens, I read error codes (Autocom 2020.23): U0422 Invalid Data Re. from BCM and U0416 Invalid Data from Vehicle dynamics Control modul, do you have any idea? thank you.

[@YepThatsIt]

hi, check all the basics first as in our 6dct450 vids. cheers

[@RatthaninWartcheeranon]

I put an aluminium deep oil pan. that help reduce2-3 degc

[@YepThatsIt]

hi, more fluid will help keep cooler, but also good idea to also add a bypass trans cooler. cheers

[@jimmyj2563]

Fit a cooler.. and you will never know you needed one..

[@YepThatsIt]

haha i`m borrowing that ! that is going to be my new cooler slogan ! cheers

[@jimmyj2563]

@@YepThatsIt Go for it .. I have sold a lot of coolers with that one!!

[@deankassan8558]

you could at least put the cooler on a angle so it gets good airflow when moving having it flat greatly reduces its efficiency

[@YepThatsIt]

thanks for that, cheers