HOW TO ADD DRIVER INFORMATION CENTER "DIC" 03-07 SILVERADO SIERRA TAHOE YUKON

[@mackjr3815]

If you have a W/T model without power door locks and windows these wires aren't in the cluster wiring harness connector.

[@ThatOneDroppedChevy]

Fuck no wonder mine didnt work

[@xNawfy]

what if u add the wire to the connector

[@Jose-sp2tj]

This is very helpful as my steering wheel controls stoped working this is a very good alternative. Seriously thanks :)

[@ne634]

Did it work for you? Myne stopped working ran a wire thru a momentary switch to yellow & i didnt work

[@bryson_cutchen]

I’m confused on what you mean by flashing the gauge, if I bring my gauge to a dealership what do I tell them I need them to do?

[@matthewyoung7042]

Very helpful I was able to view everything you showed us. How do you get the availability to select and change the settings? What wire allows you to change the settings?

[@starksgarage3334]

What wire do you tap to change the settings in vehicle settings like the puddle lights and how long they stay on and Curb View?

[@maxwoolery9868]

How much does the dealer charge to flash the gauge cluster?

[@timgreen2426]

Thank you!!! My truck has both, controls in steering wheel & the little nob. Just figured out how to use both to reset trips thank to you! :-)

[@cesaralejandroquijadajimen3917]

Hey bro thanks a lot, I have 7 months trying to find to do it, right now my cruise control work, 👍 again thanks.

[@briandeines5019]

how do I "flash" the cluster?

[@TomC-kv8pl]

Can they all go to the same ground or do they all need to be grounded to there own location?

[@Fentertainment]

I have mine grounded to the same spot.

[@TomC-kv8pl]

Ok cool thank u for the quick response. 👍🏻

[@nelsonbrum8496]

I'm wondering if I can use the factory DIC dash buttons from an 07-14 Sierra, and place them in a cubby delete plate and wire them to the dash instead of going through the steering wheel?

[@MrJazzyjeff1982]

How do u get it reflashed??

[@timgreen2426]

There are videos on that, has nothing to do with dash controls...its all manual trickery you have to perform to reset individual settings like oil life

[@kefwals8722]

Could you take these and run them through an aftermarket Android head unit? Then would you still need a flash or whatever the vin number thing is? Or would the head units capabilities automatically have a way to display them?

[@ye110wbeard]

So question. I have a 2006 Suburban with the DIC without the 4 buttons on the wheel. This does not work. Is that because a flash is needed? What is the target ... the BCM or the Instrument Cluster?

[@briankriss7310]

I have an 03 Silverado with sreering wheel controls and got a cluster out of a 03 Suburban with no steering wheel controls. How can I get it to work in my truck with all the functions I have with my other cluster? My mileage indicator is very dim hard to see in the daytime that's why I like to replace it this new cluster has a very bright indicator my gear control indicator reverse drive and all that is bright but not my mileage indicator. Or can I also take and decided that indicator out of the Suburban one and put it into my cluster resolder it into their? Thanks hope you may be able to help me.

[@dkennedy9524]

You used the orange yellow and green and white?

[@MikeBeatzcom]

I have purchased a used 2004 Chevy Tahoe LTZ and touch the button on the steering wheel. Nothing happens on the odometer cluster. I’m trying to see the miles.

[@thejuice7924]

Do you know which wires would control the radio functions?

[@gonzalogonzalez4685]

4 wires control the stereo buttons. Grey/white stripe - 12v button lights Black- ground Green- signal from switch Pink- 12v switch power Wired mine up to a SCOSCHE GM2000 interface.

[@mikelboyd711]

Do you have the pin diagram for a 2003 Chevy suburban? Or do you know where I can find it?

[@briandeines5019]

Very cool sir. How do I flash the instrument cluster? Take it out and let the dealer do it?

[@rogerterry525]

Are you able to reset all the dic choices by grounding the green wire?

[@gjolinares23]

Will this work if all I did was change to a steering wheel with controls?

[@robinhossman982]

I need to know who to replace the rolling dimmer switch underneath the vent. Can you please help me out with some info? Thanks

[@drupeydrupez]

Robin Hossman - Your comment was two years ago, but incase someone had the same question. You can buy a whole new light switch with dimmer rolling switch for about $28 on ebay brand new.

[@drupeydrupez]

All you have to do is pop off the front then pop the light switch box out and unplug the connector behind it and plug the new one in.

[@slipstreamgaming1553]

My truck has the buttons but I think my clockspring is bad. Do I need to just tap the button into the whole wire, or cut the wire and run it to a ground and switch?

[@lulop022882]

Same here, I think my clock spring is bad. They expensive AF. I’m going to use T-Taps instead of cutting the wires and was thinking of using the OE switch combo from an 08-15 Silverado. These years had a switch combo with all functions that mounted on the far left side of the dash by an AC vent. The switches are readily available, though it uses a special plug on the back. The plugs are available separate though Auto specialty supply websites. I may just get some nice looking momentary switches also.

[@ArmenArmenjs]

I loved the way you used the empty 4x4 control space for other useful add-on. Where did you get the material for the panel? Nice job.

[@Fentertainment]

I cut it from a small sheet of abs. This is a link to where I get it. amzn.to/3aG5Q5p

[@ArmenArmenjs]

@@Fentertainment Again great idea, so did you bend abs to the length of the panel or used glue to secure it from pushing IN.

[@Fentertainment]

@@ArmenArmenjs i taped the abs so a pencil mark would show. I removed the pocket and flipped it and sketed it out on the abs. I used 2 wire ties to hold it in place on the mount of the internal dash where thr pocket mounted. After I did that I placed the bezel back on the truck and sketched out the opening of the abs. Once I had the abs sketched. I removed it to find the center and drilled the holes before adding the switches and placing it for good.

[@ArmenArmenjs]

@@Fentertainment Great ! I'm thinking I may place some led lights i.imgur.com/AbNUUS8.jpg on each side lower side of the dash so I can run the switch to that empty area on council panel . The other switch on the right side is used for the front LED light bar. i.imgur.com/GNlOhQK.jpg and i.imgur.com/K4wFwWG.jpg

[@xikiloz8193]

Need some help, got a 04 silverado 1500 4.8 4x4. It don't got power windows or anything like that, can i still add the DIC if i flash or change my cluster ?

[@ladiddle4912]

Anyway I can use the steering wheel with buttons an a clock spring from the same year truck to tap just into those 3 wires an have it work?

[@Fentertainment]

Not sure if there is an additional wiring that will be needed for the steering wheel buttons. However the truck dash will need to be flashed to a truck with the same functions like I mentioned in the 1st part of the video.

[@casanovazombies356]

Say you have the steering wheel with buttons, could you put the wire to them?

[@Fentertainment]

The steering wheels might need a harness.

[@Fentertainment]

Or different clock spring. That’s why I skipped all that.

[@betourrea3179]

What about is your cluster harness don’t have a yellow wire is not pin

[@ericmartinez5633]

i have steering wheel controls. 03 duramax. i changed clock spring and new steering wheel buttons and it still dont work. do i need a reflash on the cluster ? how much that gunna cost?

[@branthenderson3050]

Is their anyway to do this without the dealer flashing it

[@hotboyzmotorsports]

Will this work ona 02 avalanche if so point me in the right direction

[@mikesaucedo714]

Does the cluster have to be flashed to a different vin like you mentioned?

[@mikesaucedo714]

And what was the point f flashing ur cluster?

[@Fentertainment]

I originally installed it with out flashing the cluster and the settings were not there. So once I flashed the cluster the settings showed up.

[@bryson_cutchen]

@@Fentertainment how do I flash it? Just get the vin number off some random truck that already has the steering wheel controls?

[@Patrick_Randolph]

Why do you have to re-flash the vin?

[@Fentertainment]

I had to reflash the cluster because it wouldn't show the driver info center when pushing the buttons. So I flashed the cluster with a similar truck with the steering wheel controls.

[@GalDemSuga]

@@Fentertainment I went the long way and replaced clockspring and the steering wheel in my 2003 Chevy Tahoe LS 4.8L V8 4WD. Now I can't find a dealership in my area (Dallas, TX) who is willing to reflash my cluster to give me the full steering wheel controls including radio control. Where do you work? What dealership? I even installed TPMS in all of the wheels and added the front passenger door switch to control them. I just need the cluster reflashed to have all these cool features. So can you help me here?

[@EGGINFOOLS]

@@GalDemSuga You can send it out to many shops to reflash and they can also add the trans temp gauge in the lower left corner. Www.gmgaugerepair.com

[@GalDemSuga]

@@EGGINFOOLS I have the trans temp gauge added. Just the reflash is needed.

[@EGGINFOOLS]

@@GalDemSuga The link I provided is the place.

[@SUBI_PaT]

Extremely late to the party but will this work on a 05 Silverado 2500hd base model with no power options at all I’d love to do this to my truck

[@Fentertainment]

Should be able to. My truck is a 04. Just got to get the cluster flashed.

[@SUBI_PaT]

@@Fentertainment what's the going rate to have the dealership flash my cluster

[@Fentertainment]

@@SUBI_PaT To be honest, I dont know. I did this many moons ago and at that time I was working at a dealership and got it done after hours.

[@SUBI_PaT]

@@Fentertainment ok buddy thanks I'll keep you posted on the outcome

[@lennylarson4192]

So I looked at my 2003 Chevy 1500 W/T model. I don't have the yellow wire. Does this mean my truck isn't capable of this?

[@EP1CNELSON]

you will have to add the wire

[@runnerman6354]

EP1CNELSON how do I add the wire I have the same thing no yellow wire

[@jasonsprouse2803]

You buy the proper GM connector, and crimp wires to them, then install into plastic fitting. Or pull a harness out of a junkyard truck with a few inches of wiring, and remove the individual wires, you need a special pin pusher set, they are maybe $5 or $6 online.

[@tommycoffin8167]

If I have it reprogrammed and put steering wheel controls on would it work?

[@Fentertainment]

Yup, also need a new clock spring for the controls and wheel.

[@alphasaiyan5760]

What if your selector switch on your cluster doesn’t work ?

[@mando94100]

I need your help!! I have gone to 3 different chevy dealer to try and get my cluster flashed and they all have no idea what im talking about. They have never heard of that in there life they all look at me like im crazy. Anyway you can help me? Anything would help

[@johnnyninetytwo]

How do I get it reprogrammed to a different vin

[@krishermanowski3599]

Do you need to reflash the speedometer to see the mpg and oil life??

[@briandeines5019]

did you ever get an answer? I want to know MPG oil life etc. but do not know what re-flashing involves.

[@Arc-Angel]

i wonder if i could do this to my 01 silverado

[@MatthewKrizic-we8tr]

I have a 2003 Silverado and I tired doing this but nothing happened. I know you said I might need my cluster flashed but I can’t seem to find a dealership that will do it. Is it possible to just get a used gauge cluster from a vehicle with DIC?

[@straitel2188]

As far as I’ve read you are able to get a used cluster with DIC and it should work. I’m in the process of adding DIC and steering wheel controls to my 05 Silverado. I’ve got an 05 LS single cab 5.3/2wd.

[@chatobalencian1504]

Can I get a steering wheel from a 07 classic with the controls and add it to my 04 with no steering wheel controls?

[@Fentertainment]

Not sure but 04 had steering wheel control option and you could get that. Might need a harness and clock spring as well.

[@chatobalencian1504]

@@Fentertainment thanks I think I can make it work by getting switches and ground out 1 prong and other run the 4 wires to that switch

[@archittt1]

could you provide us with that vin number you used so that the rest of us can add that option to our trucks?

[@Kevin_Yagoonie]

My odometer doesn't show the mileage. But it will show change engine oil and buckle seatbelt and what not. How do I fix that?

[@chadbealer4988]

Hey I have an 03 Silverado had no steering wheel controls. I add the cock Spring and steering will with controls does not work. I have tried the wire in the back to ground still nothing. How or were do you go to get your cluster re-program?

[@04titanss]

Do you have to hold down the Red button while activating the Up/Down button? Is the red button Momentary or On/Off?

[@Fentertainment]

When I made this video, that was the only switches I had. The red button was just another switch. I have since changed all of them. I just used the red switch for the reset/check mark switch. I'm gonna do this again on another Chevy I just picked up soon. Hope to make a better video that explains more

[@famous52894]

@@Fentertainment know it might be a couple years later but could you do a video of your new switches? Surely get you a decent amount of views

[@Leggett_Texas]

I tried this on my 06 gmc 1500 and it didn’t work for me! Does the cluster have to have that feature?

[@Fentertainment]

No, The cluster has to be flashed by the dealer like I mentioned @ 1:33 to a different vin number.

[@Leggett_Texas]

Oh ok I go ya now, I miss understood that part. Thank you

[@joshbridger2230]

@Fentertainment quick question. I have everything done correctly but when I'm in fuel or options which wire changes the selection? Also thanks for the video.

[@jasonsprouse2803]

I would recommend cutting the wires, and using heat shrink butt connectors. Soldering the wires creates a stiff spot, and the wires end up breaking next to the solder from vibration. I've fixed too many previous repairs where someone thought they were doing a "good job" by soldering wire. Soldering is not a factory recommended repair procedure. I'm an ASE master certified "technician".

[@Fentertainment]

I uploaded this video on May of 2016 and to this day everything has been working properly. I could care less what you are.

[@manvillercwingchun]

Lol he's salty

[@michealscott2717]

How would I explain to a dealer Tech what I want done?

[@Fentertainment]

You would tell him to re flash the cluster to a vin that had the driver information control center. So If I was you I would do the leg work and find a truck with your same year that has the dic. I looked on line and found one on auto trader I think it was.

[@caldelorey543]

i have a question, maybe 2. Seems how you know your stuff when it comes to the control of these clusters. in my case 2007 Trailblazer LT 4.2L Q1. is there a way to turn off (disable) the DIC. 100% Q2. In lieu of turning off the all DIC 100%, is there certain wires (color sensitive) that are ok to remove from the pin connection that reads (service tire monitor) and (service stabilitrak) I can put tape on the warning lights for these two issues, but the at the message center (DIC) I would prefer to just remove that logic as described above and still keep my Odometer reads and other programmable features. Hope to hear back soon,, Thanks Please let me know

[@Fentertainment]

Cal Delorey not sure, when I made this video I was working for a dealership and had tech's help me to program the cluster. I'm sorry I'm no help.

[@tonymeehan7859]

I want to do this to my 07. So you only used the yellow, green and orange I assume? Did you just ground them to the same location under a bolt? thanks!

[@Fentertainment]

Yes but like mentioned in the video you have to have your cluster flashed to a truck that has the same features.

[@tonymeehan7859]

@@Fentertainment ok, got ya, so much for that idea lol

[@erickgomez7833]

I have a 06 silverado 4 door and i do all that but not work can you tell me whay please thenks

[@raymondkloehn1145]

Wrong guage cluster

[@gortiz5583]

would you know how to change the kilometers to miles on the odometer. my chevy is an 03 as well with no steering wheel controls. thanks

[@hiddenInsight486]

With odometer displayed you can press and hold the button to bring up the option

[@MattsHackRods]

How do you flash it? Where do I go to get that done?

[@NJhuskey]

find out?

[@MattsHackRods]

@@NJhuskey nope

[@cameronmaclachlan4382]

Your local chevy dealership needs to flash it

[@johnnormanhunt]

You can send the cluster to a place that specializes in cluster repairs. They have the equipment and bin files needed to flash it

[@TomC-kv8pl]

I have a 2004 GMC Sierra 1500 sle reg cab short bed. I put a Denali cluster in it. All I would need to do is add the buttons cuz a Denali already has the steering wheel controls correct????

[@Fentertainment]

I think so.

[@TomC-kv8pl]

Fentertainment thank u

[@AlexRodriguez-pg9xk]

@@TomC-kv8pl did it work? I had an Escalade cluster added to mine and have yet to try it out

[@TomC-kv8pl]

@@AlexRodriguez-pg9xk works perfect. Super easy also.

[@AlexRodriguez-pg9xk]

@@TomC-kv8pl awesome to know I won’t have to have it flashed. Thank you

[@thomasdearing7718]

I have a 2000 z71 does mine have that option?

[@austinguidry7774]

So basically for it to work, I need to reflash it to another vin?

[@Fentertainment]

Yeah, I had to do it. I have a dic switch that I just purchased from a 07-13 truck on ebay for $20. I need to replace them ugly switches I installed with it.

[@austinguidry7774]

+Fentertainment when can I get that done? I guess I have too, because I just tried the fuel econ, to a ground like you did and literally nothing happened

[@austinguidry7774]

+Fentertainment where*

[@Fentertainment]

Any dealership should be able to do it for you. I would try to speak with a technician because they may do it on the side instead of giving the dealership money also. Basically anyone who owns a Tech2 tool for programming.

[@austinguidry7774]

+Fentertainment so, I need to get a vin from a truck that has the steering wheel with the buttons? If so, how do I acquire one?

[@elihickey02]

Will this work for a 2000 GMC Yukon? Or is there anyway I could just get a newer year model cluster and do this?

[@gagemosley8365]

nope 03-07

[@joeygarza2699]

I have an 03 chevy avalanche that’s has the steering controls but the dic doesn’t work it says change oil but when I press the buttons nothing happens. Anyone know what going on by chance.

[@eddielerma1174]

Where did u get parts ??

[@rdcampos1]

This is a GREAT video!!! Thank you for taking the time to do this... now that I have laid it on thick I have a question? You knew that was coming! 😀 In one of your recent posts you said that you were going to do another video, showing a different switch. Do you know when you will be doing it? I have a 2006 Silverado 2500 duramax. In order to get the correct flash should I find the same make/model/engine and year? My steering wheel does NOT have the control buttons and I am trying to do this at a reasonable cost. I am pretty comfortable around a truck and wrench. Could I use a dash mounted switch for a 2007??? Again, your time and effort to help country guy out, is greatly appreciated. I will have s cold one in you name!

[@Fentertainment]

The switch question, I took 4 momentary switches and took my time to make a plate to fit that cubby where the 4wd switch goes. It looks better than what I have in this video. I also purchased a 07up dic switch but couldnt get it to work. My steering wheel doesnt have switches either, That is why I made the switch plate for the truck. Other than that I havent changed anything and it still works perfect. I picked up another 04 silverado. I called my buddy at the dealership and I'm gonna get him to flash this cluster as well. It will probably be on both of our youtube channels. I will take the time to show a switch plate like I have in mine on that video as well.

[@rdcampos1]

Thanks for the reply. Although I now have a couple of other questions.... I know I can easily test to see if the cluster will display info without flashing. But if it doesn’t and I need to have a dealership flash the cluster, do i need the truck and the cluster or can I just take the cluster to them with a valid VIN? I was also thinking of chipping or otherwise modifying the duramax Do you know if any monitors will display the DIC data?

[@Fentertainment]

@@rdcampos1 I carried my truck. The tool that he used plugged into the obd2 port.

[@rafaelramirez9857]

How can you select on each option?? The reason I’m asking it’s because I added side mirrors that have poodle lights and since my truck don’t have the steering controls I need to change it on the cluster

[@starksgarage3334]

Yessss I’m so dam curious…

[@tjnoer3749]

It would be nice if you would respond to these questions

[@essinnocents7125]

I tapped in to the wires and it still didn’t work you know why?

[@bikemike6953]

would this work in a 2000 gmc sonoma?

[@Fentertainment]

not sure about the sonoma's or s10's.

[@1031negro]

@@Fentertainment what about a 2000 gmc sierra

[@truckinman86]

@@1031negro No, Between 1999 and 2002, this body came with a DIC that pretty much only showed warning messages. It wasn’t until 2003 when a lot more electronics and other convince items showed up.

[@jasonhirt367]

So Fentertainment, I have a 2008 Chevy Silverado 3500 HD Diesel and I currently do not have the options for mpg and so on. Would I still need a different vin and reflash?

[@Fentertainment]

Jason Hirt I'm not sure. I think you maybe able to add it. I would search the forums.

[@craigroznowsky1028]

Mine didn’t need a reflash I went to the auto wrecker and pulled one from another vehicle. Cut a hole in upper right corner where unit plugs in and it works!

[@craigroznowsky1028]

Mine was a 2007 Chevy Silverado

[@runnerman6354]

Fentertainment I have an 03 Silverado wt and it does not have 4 wires how do I do it

[@alexayala6720]

I tried it ain’t working I sliced the yellow wire ram long wire same bullet for ground didn’t get no fuel reading ??? Am I missing something

[@Fentertainment]

Still have to flash the cluster to a truck with driver information controls

[@alexayala6720]

@@Fentertainment thanks for the reply by flash what do you mean by that ?

[@alexayala6720]

Do I just go to Chevy dealership ? Feel like they wouldn’t even take me serious since it’s a 18 year old truck

[@Fentertainment]

@@alexayala6720 The cluster needs to be flashed with a tech2 to a different vin of a truck with a cluster that has the dic.

[@MostWantedRaed]

will this work on a 09 trailblazer ls?

[@Fentertainment]

not sure. It may but remember you will have to get it reflashed.

[@MostWantedRaed]

Fentertainment got it, thank you

[@KennyG488]

Great video very helpful!!!!

[@breakinggames6356]

Im going to try adding this to my sle sierra that was optioned without the steering wheel controls

[@Perforated611]

What about in reverse? Have a new cluster (old one cooked itself), have steering wheel controls but they don't seem to talk to the new cluster, assuming it came out of a truck without the wheel controls in it, does that make the cluster different?

[@danny_games2275]

Same problem with mine. Have you figured it out?

[@Perforated611]

@@danny_games2275 according to a few resources at the time it needed the EEPROM reprogrammed to include the steering controls. However my situation turned out to be bad steering controls.

[@danny_games2275]

@@Perforated611 I havent really messed with mine, I guess I'm going to see if i can reprogram. Did you have to replace just the controls or sterring wheel as well?

[@Perforated611]

@@danny_games2275 I haven't fixed it yet, it involves changing the steering wheel clock spring, which is just a pain.

[@danny_games2275]

@@Perforated611 I hear you thanks for the info

[@bentvalvesnthrownrods3057]

I opens up my 05 Sierra 3500 work truck and diddnt see those color wires. I grounded out the yellow wire I thought it was and turns out that was the power wire

[@mr.anderson910]

My 2003 Silverado don’t have the yellow wire😩

[@mikewerth6113]

So I have to have flashed to my Vin to my truck again? Then it will work? This is very cool.thank you

[@ericmartinez5633]

exactly what im thinking. i have the original cluster (at least i think) and i have new steering wheel controls, a new clock spring, and still nothing. so maybe a reflash is needed for some reason

[@straitel2188]

@@ericmartinez5633did you ever figure anything out?

[@ericmartinez5633]

@@straitel2188 yes i had to get a programmer to tell the cluster to add the options. so i ended up buying a 350 cluster with it already programmed. :)

[@JaylaHoffman]

Anyone know how to do this on a 04 Malibu LS ?

[@Trident_Euclid]

Where did buy those momentary switches?

[@kevina4674]

When you get it flashed to a different vin. Does it change the mileage of the truck to the vin of the other?

[@Fentertainment]

no it stayed the same. It basically unlocked the features.

[@Barrett-tq7pq]

I’ve had my truck for 9 months and I never even noticed that little thing sticking out of the cluster.... I also grew up in this truck which makes me feel even more stupid

[@joshuabrown4181]

So you just basically ground the wires

[@jasonsprouse2803]

No. You connect through a momentary switch, and from there to ground. The ground is the signal for the change. If you just connect to ground, you can't change anything.

[@victorcardenas324]

You don't show where you hook the other wires

[@arielvazquez207]

How do I reset the total fuel used? Mine says 99999 and I can't reset it. Thanks for your help.

[@timgreen2426]

Youtune has videos how to reset...dont need controls bc its all manual trickery tasks you have to perform...like key on key off pump brake 13 times....that kind of shit.

[@TheDiegoKidd]

My truck used to have the options to display oil life, instant mpg, etc. But at some point the options stopped showing and my engine hours went back to zero even with 170k still on the odometer. No clue happened but maybe this will work.

[@SmileyJay810]

Check your Radio amp fuses I've found replacing that fixed my problem 🤭

[@revenger8269]

That is awesome

[@hollywd269]

I tried this on my 2004 Silverado 2500hd and no luck but awesome video, maybe the 1500 is wired just a little different. But thanks for the info.

[@Fentertainment]

Did you have the dealership reflash the cluster to a different vehicle with these options?

[@hollywd269]

@@Fentertainment no I didn't, I remember you saying that at the beginning of your video. I didn't put that together till now that the vehicle has to be flashed for those options. Thanks for the info!

[@PROATV13rb]

@@Fentertainment What if you got a cluster out of a Cadillac Escalade? Then you wouldn't have to have it reflashed correct?

[@Fentertainment]

@@PROATV13rb Not sure. I had a escalade cluster back in 03 on my 02 that was bagged with a caddy front end. I dont believe it had the dic controls to where I could use it. I cant answer that. Need to ask someone else with a definite answer, I dont wanna tell you something else.

[@PROATV13rb]

@@Fentertainment it works bro I just peeled it out and checked. Says I'm getting average 7mpg tho yikes!! So I only did thr one wires far the tallow wire and seems to show fuel and oil do I need to do the others.?

[@Jp_5ive3hree]

I have a 2005 GMC Sierra 1500 and the avg Econ has been stuck on 13.9 for 2 years now never goes up or down I’m not sure how to fix it

[@jerrynavarrete7014]

me lo podria traducir en español x fabor🙏🙏🙏🙏

[@blainelittleton8520]

Don’t do this, it doesn’t work without doing a long draw out process of re programming and everything else. NOT AS EASY AS CLAIMED. He should mention it in the video. Trying to save anyone else from a waste of time like it was to me

[@Fentertainment]

Maybe you should have watched the entire video and not skip around. At 1:30 I explained I had the cluster reflashed to a different vin number in order for this to work. So it was claimed MORON!

[@davidcolgan2420]

You did say that but you didn't say WHY it was done

[@james10739]

He only said that it was flashed with a new vin which just saying that means nothing really

[@24BLUEELMO]

Add a trans temp gauge

[@toddhaines7956]

kzbin.info/www/bejne/bnfOqmCEbraEhqc

[@timmensch3601]

to add atrans temp you need to get a cluster with the trans temp guage i.e. escalade cluster and it is plug and play

[@toddhaines7956]

@@timmensch3601 no need to get another cluster. It can be added to any 6 gauge cluster from 2003 through 2006

[@toddhaines7956]

These guys do it at a reasonable price: www.gmgaugerepair.com/add-a-transmission-temperature-gauge/

[@jacobblair3282]

So I only have to flash the cluster and hook up the wires for it to work? why do I need a new clock spring does that have to be out of newer truck?

[@Fentertainment]

I think if you were to buy a steering wheel with the controls already in the wheel then you would have to.

[@gabrielmalcolm4812]

If I went the clockspring and harness route, would I need to reflash?

[@Fentertainment]

I believe so. The clock spring and harness is just the right way it should look instead of cheap switches like I used.

[@dmocksautosnstuff]

Will this work on 2003 Tahoe bought new cluster and it doesn’t show the mpg and miles to empty any more ?

[@tjnoer3749]

Answer the damn question what the heck