In this short video I show you have to diagnose a bad gasket, how to change it, and what to do. Check out our website at chlorinekingpools.com
Пікірлер: 27
@donl3533 жыл бұрын
So many other videos for this have incorrect or missing info. Finally one that's correct and short. After 25 yrs, just learned I could have been using my vinyl patch glue which is always on my truck! The one adhesive I never thought about for this.
@ChlorineKingPoolService3 жыл бұрын
Glad it was helpful and thanks for watching!
@talmillican93656 жыл бұрын
After removing the screws, re-attach those hex nuts back to the screws so they don't run away. Home Depot sells a small magnet cup to hold hardware like valve cover screws, etc. Good job, Eric!
@ChlorineKingPoolService6 жыл бұрын
Thanks Tal. Been meaning to get around to doing a review on your awesome multitork set. I actually have one of those in my garage. Not a bad idea to bring it out for these types of jobs.
@sharontrigg343 жыл бұрын
thanks for uploading ready to have a go at it.
@amandamiller33794 жыл бұрын
I have a question, I have to change my spider gasket in mine and am having trouble getting the water out of that area. I used the shop vac but it kept filling up just enough to where I need to glue down the new gasket. Pump is off, pressure released. Do I need to just use the shop vac longer to clean the lines? I can't find anything about it online so far. Thanks and great instruction on this one!
@ChlorineKingPoolService4 жыл бұрын
Is the equipment pad below the level of the water by chance?
@Afrikaansoldies4 жыл бұрын
@@ChlorineKingPoolService yes
@hugohernandez87834 жыл бұрын
Great job. How long did you wait to light the pool again when you put the cylinder???
@ChlorineKingPoolService4 жыл бұрын
I turned it on pretty much immediately.
@byronorona66592 жыл бұрын
i have algea going back into the pool, my valve lever does not spring back all the way up, can that cause the sand filter to not filter the algea and put it back into the pool or is it the spider gasket?
@heathersteele55604 жыл бұрын
Very helpful video. 2 Quick questions...What is the purpose of the lube and can any lube be used?
@ChlorineKingPoolService4 жыл бұрын
Lube is used to help seal the gasket against the MPV body. It’s always great to lube all accessible O-rings as a general rule of thumb. You’ll want to use a silicone based lubricant like magic lube so it doesn’t degrade the o-rings.
@deb57004 жыл бұрын
Can a bad spider gasket cause DE to leak into the pool? All of our de was coming back in the pool last season, but it didn't seem to be any of the typical reasons. It never seemed to come right back into the pool. It seemed like it wasn't until we would turn off the filter that it would end up in the pool.
@ChlorineKingPoolService4 жыл бұрын
Yes it can for sure.
@cardo11116 жыл бұрын
Very helpful vid, thanks for posting it. Did the spider gasket come glued on from the factory?
@ChlorineKingPoolService6 жыл бұрын
You're welcome. This one was glued in. It was a pretty old filter so there's no way to tell if it was original or replaced already.
@alanpierson82423 жыл бұрын
Can I use silicone instead of lock tite? I did 10 years ago when I replaced it last, was I just lucky?
@ChlorineKingPoolService3 жыл бұрын
Silicone is fine. Using adhesive isn’t 100% mandatory but just helps. Thanks for watching.
@alanpierson82423 жыл бұрын
I changed the gasket on Sunday without using any adhesive and on Monday I backwashed and rinsed and when I switched back to filter water continued out the discharged hose , is there anything else I could have done wrong , Iam going to use silicone when I replace the gasket tonight , Thanks! @@ChlorineKingPoolService
@ChlorineKingPoolService3 жыл бұрын
I can’t imagine the gasket was torn after one use. Make sure the rib of the gasket is facing in the right direction.
@alanpierson82423 жыл бұрын
@@ChlorineKingPoolService The ribs were facing up , and I should clarify, it did not tear it was stretched about two inchs out of its groove. Thanks!
@ChlorineKingPoolService3 жыл бұрын
Perfect. Glad you figured it out!
@lexdelosreyes66774 жыл бұрын
what happened the swimming pool if 10 years not change the sand filter
@ChlorineKingPoolService4 жыл бұрын
You’ll have a harder time keeping the pool balanced and you’ll have a harder time keeping the pool clear. More than likely easier to turn green or develop some algae growth quicker.
@mytexasdays15265 жыл бұрын
My old spider gasket is glued in. How do you get it out? Acetone and alcohol are no help.
@ChlorineKingPoolService5 жыл бұрын
You can take small flat head (a smidge smaller than the channel the gaskets in) and start scraping. It'll take a few minutes but you should be able to get it all out.