This video show how to take apart the hook assembly if thread or a broken needle are jammed inside.
Пікірлер: 61
@lizhawkes39362 жыл бұрын
Great video, thank you. Saved me a 2 hour drive to the repair shop!
@Sewinggold2 жыл бұрын
Glad it helped
@sandollarstudio8033 жыл бұрын
Thank you Alberto and Steve.
@jeffwardecke22303 жыл бұрын
Hot tip: you do not have to remove the position finger screw all the way, just enough to pull down the finger keeper out of the slot, then rotate the bobbin -(both will most likely rotate at the same time - inner and outer since the tread is still jammed) then push the finger back up into place, temporarily retightening the finger position screw if necessary. Finish as instructed on the vid - (magnetic screwdriver for sure!) and then just reverse the procedure, Saves one hassel anyway. It works; I've done it a dozen time and still can't figure out why it keeps jamming, very frustrating. Have fun - Cheers
@stephaniebabin24412 жыл бұрын
Best video out there!!! Finally someone gets it when we ask "how to unjam a machine!" Now, my thread cutter is still jammed on my Juki TL-18QVP and I have no idea where it is. I can't see any threads anywhere that would be cause such a horrendous noise when I press the button.
@tungluong5507Ай бұрын
Thanks and millions thanks for this clip. So helpful❤
@russellfoote39105 жыл бұрын
make sure the top slot in the basket is at the 12 o'clock position before you put that basket stop (with red marker line up) back on. If it's not, you will be doing the position finger over and it's very hard to get the screw started.
@wrthrash3 жыл бұрын
I owe you guys a beer, saved my Consew P1206's bacon today, jammed up tight BUT now it's alright! Thanks mucho!
@beyondview Жыл бұрын
Thank you so much!! I watched so many videos that did not help but this video did thank you
@AnnFrank-kq4fk10 ай бұрын
Just three words.... I love you!!! You have saved me again..... Thanks!
@Sewinggold9 ай бұрын
Glad I could help!
@le_maroquin28163 жыл бұрын
thank you for sharing this video i had a same problem with a toyota machine .. when the needle form a litlle loop the hook wasn't sharp enough and it refuse to grab' the thread loop ,....
@SherryCarrigan14 жыл бұрын
Thank you so much Steve for this video. I was able to reposition my hook basket and get back up up and running in just minutes. Appreciate all you do!
@Sewinggold4 жыл бұрын
No problem Sherry. I'm glad it got you up and running.
@michaelcooksmd3 жыл бұрын
Thanks a lot! Back up and working in a short time. Keep up the maintenance infor!
@Sewinggold3 жыл бұрын
Glad it helped!
@miaforte85364 жыл бұрын
Thanks Steve. Have used this video to unjam my 8700H. Slightly different. But was able to make it work.
@Sewinggold4 жыл бұрын
Glad it helped.
@bear90204 жыл бұрын
I finally got my new machine sewing. I think that in shipping, things loosened up and the heavy T135 thread threw the timing all out of whack. Using T90, she sews now, but the safety clutch is locking way too often. New thread, new needles, just continues to lock up. Is there something I'm doing wrong? Thanks!
@ewaoluwabalogun3 жыл бұрын
There's no thread stuck in mine, do I just loosen the first part and turn it then fix it back? Or I have to still take out the three screws
@nyjohn0064 жыл бұрын
Hi Steve, I have a Pfaff 563 where the shuttle bobbin doesn't spin when using the machine via the motor. It's not stuck as you can move it with your finger. Really perplexed. Any idea as what could be the problem? Thanks!
@mw3designs Жыл бұрын
I finally picked up a 1541s, and am getting it setup for sewing leather. I have noticed that the walking foot does not go up very high when sewing, and has difficulty sewing over layers. Is there an adjustment, or is something wrong with my machine?
@debrapotvin3163 жыл бұрын
I have a 1181 but now it won't pick up the bobbin thread and it seems like the inside of the case where the bobbin goes it moves around is that suppose to happen
@RobertCorbin-kf3zc Жыл бұрын
My Juki DNU 1541 (not the S model) is jammed. I've removed the bobbin case and found tangled threads in it. I think I need to go through the process in this video, but how would that process differ with a 1541? Thanks in advance!
@lindac.98802 жыл бұрын
I just found your channel and have a sewing machine question for you. I purchased an old Consew industrial machine (DDS-500) that I have used on probably 10 projects (projects my standard machine can't handle). Yesterday, I was altering my third pair of denim jeans and the machine jammed. There was no warning noise or broken thread, just completely stopped. The needle is stuck down in the bobbin (almost all the way down) and I can't budge the motor wheel at all (seriously, it doesn't move at all). I have looked for videos to help, but all of them tell me to remove the bobbin case first, but the bobbin case doesn't budge (assume it's because the needle is down in it). Are you able to advise on the steps I need to fix this issue? Do I start with loosening the position finger/bar first? Thank you in advance.
@leahdmarkman Жыл бұрын
Is this waht I should do if my bobbin case is stuck in the chamber.
@youaxeng3 жыл бұрын
I have issues my too. My model 8700 after I setup sewing bit then jam. I take out putting back not working
@tatumsupholstery Жыл бұрын
Steve - my 1541 sews great - but keeps breaking thread in reverse? Any suggestions- thanks Mike
@mzkitty1925Ай бұрын
Thank you
@SubLike2473 жыл бұрын
What if you followed all of these steps and you can’t rotate that hook bar, what would you say then?
@rhondahawkins91743 жыл бұрын
I have a brand new Juki du1181n. I just got it set up and I tried to sew. I get an error 7code and the hand wheel will not turn at all.
@kathyslater99072 жыл бұрын
My hook assembly jammed today on my 1181. I cannot get my bobbin case out and the needle is down. Needle appears to be free but hook won't turn. Help!
@florentinarin7728 Жыл бұрын
Hi. I have a Juki ddl8700-7, with cp-160 and control box SC-910A. Whe I stop sewing machine needle stop down and the knife of thread trim is hitting the needle and blocking the movement of sewing machine put motor in overload. What is the problem?
@marsanhe2 жыл бұрын
How can I prevent this to continue happening?
@bear90204 жыл бұрын
Excellent video, but, my brand new 1541S jammed up after only an hour or so of sewing. No matter how many times I reset the clutch, it still jammed. I took it all apart, per your video, and have found that the position finger doesn't slide into the hook basket far enough, to hold it, and the hook basket stop finger doesn't protrude into the basket fat enough to act as a stop. the basket keeps spinning a short way, until it jams, with both stops becoming unseated. This is a brand new machine and I have already spent days, trying to get it straightened out. Any ideas why these two parts won't reach? Thank you!
@Sewinggold4 жыл бұрын
Have you tried bending the position finger to get it closer to the basket? Be careful not to break it.
@PMReed4 жыл бұрын
SewingGold.com - I tried bending it just a bit. It's a pretty sturdy piece. Hoping to conference call with a mechanic, from the place I bought it, on Monday. Tough way to start a relationship with a new machine. Thank you for your reply!
@DrStephanieMillerWilliams4 жыл бұрын
Steve, can you do this with the Juki 1181n also?
@Sewinggold4 жыл бұрын
It is virtually the same. The DNU-1541 series has a few extra parts.
@SP-gf2ti4 жыл бұрын
Thank you for this video! It is exactly what I needed to know and very helpful. I am having trouble getting the screw our of the opener. I tried an Allen wrench and it did not pop out like yours did. It may be stripped. Any suggestions? Also, the opener seems to be stuck on the hook in certain places when I move the wheel? Do you know why that may be? Thanks!
@Sewinggold4 жыл бұрын
Unfortunately I do not. Are you sure it is the correct size. More then likely it is metric.
@SP-gf2ti4 жыл бұрын
@@Sewinggold thank you. I figured it out. It was actually the safety switch. I watched your other video to disengage it.
@yonivanhooff52402 жыл бұрын
Hii, my DU1181N got jammed in the bobbin case holder? by a broken needle.. any tips? Tried the same by these steps and he can turn again.. but the new needle continually touches the bobbincase, bobbin case doesn’t go in as easy as normal and the thread doesn’t pick itself up
@Sewinggold2 жыл бұрын
Please email me some pictures or better yet, a video. info@sewinggold.com
@muhammadfayyaz27353 жыл бұрын
Sir G Jockey sewing machine is fitted by the company with double stitches. While the mechanic puts single stitches during the repair, I want to know in detail why the double stitches do not work properly after repairing.
@latamalhotra43414 жыл бұрын
Can you help me with my sewing machine - bobbin case got stuck in driver and can’t take it out. Brand is Lemair Pacesetter super full automatic 703 .
@Sewinggold4 жыл бұрын
Unfortunately I am not familiar with the brand or model. If you post a video of the machine and the problem, I can try.
@latamalhotra43414 жыл бұрын
Thank you very much for replying. I have managed to take it out. Thanks again
@barbarawilson62684 жыл бұрын
I went through all the steps to remove a jamed thread and now my 1541 won't actually make a stitch. Any idea what might be wrong?
My hook assembly stopped spinning. Did I break a gear or something?
@Sewinggold Жыл бұрын
It is probably your safety clutch. Watch this: kzbin.info/www/bejne/rGOoZYeXna9paLM
@jjk109 Жыл бұрын
If you lose those screws you’re screwed 😮
@ahhhlex.h Жыл бұрын
Mine won’t spin at all? I wonder if I should do this?
@Sewinggold Жыл бұрын
It is probably the safety clutch. We have 2 or 3 videos on how to fix that problem.
@maezimmerman23404 жыл бұрын
Hi! My machine caught a thread and it is really jammed up...won't even turned...do you have any tutorial which is showing something different? Need help😢😢😢
@Sewinggold4 жыл бұрын
This is the correct video. If you remove the position finger and opener first, the hook will rotate so you can remove the screws to take the hook apart.
@delmarzenobi16494 жыл бұрын
THIS VIDEO SAVED MY BUTT THANK YOU FOR POSTING IT!!!!!!!
@Sewinggold4 жыл бұрын
No problem.
@jonnyphenomenon5 жыл бұрын
Good god... I hope this doesn't happen very often...