I watched you video about 2 pm. Searched the net for parts (40 miles away). Got there before they closed. Traveled home with the board and the switch. The board did the trick! Thank you! Didn’t need the switch, no biggie by 9pm I’m cleaning up tools and the dishes are being cleaned and the wife is happy. 👍🏻
@JankyShack3 жыл бұрын
Glad you were able to get it fixed!
@rafaelcuriel50663 жыл бұрын
This video was the only one that help me repair my GE PDT825SSJ0SS. It helps you troubleshoot the issue and get rid of this very annoying problem, the constant beeping and the dishwasher not been able to start a cycle. THANK YOU - GREAT VIDEO!
@rjhacker3 жыл бұрын
This was the solution that fixed it, I saved hundreds of dollars. Got the beeping chime and indication the door was open from the diagnostic mode. I replaced the switch with a genuine new one, so I didn't have to test it. The circuit board was the culprit. Thanks Janky Shack
@mjayjock13 жыл бұрын
You are the man! My GDF520PSJ2SS had NO lights or responsiveness. We found and cycled the breaker and nothing. Then I saw the beginning of your video when you said that you had to recycle the breaker many times to get it going for a few months. I recycled the breaker again twice and up she came! Many thanks, you have a grateful subscriber. Hopefully it will not go bad on me but if it does I am buying a better dishwasher. I have installed them in the past and that does not seem much different or more difficult than a major repair. These GE builder-grade DW seem to do down a lot.
@stevep81323 жыл бұрын
Your advice is right on man. Thank you for running through some basic troubleshooting such as resetting the dishwasher at the breaker panel. I followed your advice and flipped the breaker on and off 5 times leaving the breaker in the on position at the end. You were right that it did reset the door sensor and that allows me to at least run the load inside until I can replace the door latch sensor WD21X10490. Again, thanks for the detailed instruct. Steven
@myvideos8315 Жыл бұрын
Thank you so much! Changed out my mother board. Door open problem solved. I have 3 good door switches now🤨! Glad I came across your vid! Best
@comlywhiteley769311 ай бұрын
thank you so much for helping me diagnose my issue with my GE dishwasher. very helpful.
@JankyShack11 ай бұрын
No Problem!
@GaryASobek3 жыл бұрын
Thanks for the help. 3-year old dishwasher had same issue. Followed your troubleshooting, got same results, so ordered new control board. Will find out when it gets here if that fixes my issue.
@rickjjian3 жыл бұрын
thank you Sir. The symptoms are exactly like yours. After the reset, the lights were blinking, indicating door not closed but actually it was tightly closed. I ordered a new control board, and followed your instruction and fix my machine!
@peterj.d.87372 жыл бұрын
Janky, finally a GE like my machine! I replaced the controller board with an old one from my neighbor while waiting for my delivery. His board lights went on, once I flipped the circuit breaker 10x, the START button lit up and it RAN!! I previously took the shield off, then the board out, ran the replacement board while it was hanging, then I could see the lights, they blink when the machine is running. I'm going to order that door sensor wd21x10490 for the future. My machine GDF57oss2ss, board wd21x24901 $99. Thanks, Great info!!
@stonecreekmasonry92823 жыл бұрын
This was exactly what I needed to do the repairs on my dishwasher. Thanks for your research and video.
@JankyShack3 жыл бұрын
Glad it worked out for you!
@dawns44672 жыл бұрын
Nice job! Impressed that you did all that, pretty much one handed. Thanks for sharing your experience.
@JankyShack2 жыл бұрын
Thanks!
@lukeloeffler383 жыл бұрын
The troubleshooting with the multimeter was awesome and yes, my board was dead and my latch was fine. Thanks for helping save some cash.
@PH-md8xp3 жыл бұрын
Helpful, thanks. Having a similar problem with a later model ( GDF620HSJ6SS ), have ordered both the machine control module and the UI module. Your video helped with preparing to swap out the old boards with the new.
@markvtri43213 жыл бұрын
This helped me figure out my switch was good and I needed a new logic board. Thanks!
@studentoftheintellectualda57303 жыл бұрын
You saved me from buying a new dishwasher! Thank you!
@kevhouse553 жыл бұрын
Great info in the video. Thanks for the help. You save my dishwasher from a death of fire and bullets
@BarNoneWranglers3 жыл бұрын
Outstanding troubleshooting video. Thanks.
@erintwaddell31813 жыл бұрын
Same problem with mine. Turned out to be the mother board too. Thanks for the video.
@gabrielswenson42983 жыл бұрын
This is very informative and helpful. I got the information I needed then watched the enjoyed the rest of the video. Great work. Nice knife!
@shamusnilan63583 жыл бұрын
Thanks Jack , this is exactly what i needed to see
@bobelmore62923 жыл бұрын
Great video, just replaced my control board after watching your video and sure enough that fixed it.
@JankyShack3 жыл бұрын
Glad it helped!
@showmemotorcyclelife44054 жыл бұрын
Thanks for the video helped me dial in and fix it for what it would have cost just to get someone here to look at it
@JankyShack4 жыл бұрын
Glad it helped!
@snowmanfl3 жыл бұрын
Thanks, your video helped me to repair me dishwasher today!
@nizamahmed1462 жыл бұрын
Thank you very much for this demonstration! Though my dishwasher model is a bit different than yours but your demonstration helped me to understand and fix mine in the first try! Very helpful!!
@JankyShack2 жыл бұрын
Glad it helped!
@MichaelStJohn-du2db3 жыл бұрын
Thank you for making this video.
@JankyShack3 жыл бұрын
You're Welcome!
@tmart44803 жыл бұрын
Thank you so much for making this! I had the same exact problem.
@Tonylovesjazz11 ай бұрын
Hah! Reset the circuit breaker for 1 minute!!! 🤣Had to re-install the old float switch, door latch and UI controller. Thanks. Saved me $150.
@bettytatum44454 жыл бұрын
Thank you so much. That really really helped.
@MoOutdoorsandReviews2 жыл бұрын
great video, I am working on fixing mine now
@arlinimartini5033 жыл бұрын
Thank you for your video! It helped me diagnose and fix my dishwasher!
@JankyShack2 жыл бұрын
You're welcome!
@denashrum59443 жыл бұрын
super helpful! thank you!
@peterj.d.87372 жыл бұрын
Neighbors didn't last, my new delivery came in and was installed-working perfectly. 1) had to unscrew the 110 ac terminal to get proper access, and I did remove the top surrounding shield, on the closing process there was a "lip" on this shield which I ground off which made the install effortless.
@zenc43993 жыл бұрын
You are the best helper.
@bartryun3 жыл бұрын
Very Helpful Thanks Much
@thewulvrine80423 жыл бұрын
Needle nose pliers make quick work of removing the board from the pins
@TheJont1183 жыл бұрын
Thanks dude.
@JankyShack3 жыл бұрын
You're Welcome!
@bdyt10013 жыл бұрын
Very helpful video. Both switches inside my door latch measure 0.8 ohms. Is that sufficient resistance for them to work properly?
@JankyShack3 жыл бұрын
Yes 0.8 is low enough
@bdyt10013 жыл бұрын
@@JankyShack In the end, it was indeed the control board in my 2016 model, which I replaced. Thanks for much for your video, I have a happy family now.
@garyhall97803 жыл бұрын
Thank you!
@maryyalda35104 жыл бұрын
Nice details
@JankyShack4 жыл бұрын
Thank you! Cheers!
@chesterpuett73 жыл бұрын
Awesome was very helpful
@elizabethcansler94852 жыл бұрын
I have been unable to find diagnostic/ tech paper online. Can you post a link on the comments?
@JankyShack2 жыл бұрын
I found the paper on the outside of my dishwasher when I pulled it out. I don't live there anymore so I don't have access to the document anymore
@HimsinBoston3 жыл бұрын
Hi , My bottom circuit board solid light green, bottom of machine controller board. But my buttons don’t ON. No power to up buttons, which board is dead? Top one buttons or controller?
@ellenmonday5073 жыл бұрын
Thank you You just saved me $75
@richardvisco63703 жыл бұрын
Does that control board run the whole dishwasher
@josephfolsom20303 жыл бұрын
GE recommends not only to replace the board you did, but also the user interface at the same time. Absolute garbage. I’m an appliance technician ( for 39 years )and I see this constantly on 2-4 year old machines sometimes sooner. There is also a resettable thermostat under the dishwasher which will trip. You have to replace the wiring harness to get the thermostat since they solder the wires to the thermostat and also shrink tube it so you can’t even test it. It’s in series with the heating element. You have to pull the dishwasher to even get to it. I wouldn’t recommend an LG or Samsung ever for replacement either. Try a medium or higher end Whirlpool product. You can get away at $700 on sale. Always get the extended warranty with new appliances. Never used to say that, but times have changed and so has manufacturing quality.
@TC-tw5zk3 жыл бұрын
I thought Samsung had problems too? Or is that old news.....I'm looking to purchase a new one. I took out my latch switch used contact cleaner and small brush...works good..will see how long..
I have this exact model. My recalculate pump isn't working. Can you give me the model #. My tag came off the door.
@hotrolls34733 жыл бұрын
My GE dishwasher, model GDT695SGJBB, has no lights or functionality whatsoever. Tried all scenarios on the service information sheet. Will not enter error mode or service mode. Accessed the main board at the bottom of the door. Service LED light is solid green, wether the door is opened or closed. No flashing pattern. Service information sheet indicates this means the door is closed. Replaced the UI board ( WD21X23426) , still having the same problem. Each board is around $100. Have not priced a latch. Not sure what to do next. Repairman would most likely be a $75 service call plus his time and the part(s). Wondering if I should just replace the other board and latch too🙄?
@JankyShack3 жыл бұрын
have you measured the resistance of the latch with a multimeter? according to the internet the latch is a common failure point.
@hotrolls34733 жыл бұрын
@@JankyShack I appreciate your time. Yes. When I check the ohms on each of the pins, it shows 0 when the door is closed. When I initially open the door, each pin reading spikes to anywhere from 1.87-2.47 but then goes immediately to a reading of 1 and does not fluctuate. That not how your ohms readings were registering but I thought since it wasn’t reading 0 that the sensor might still be good.
@charlesboppe22623 жыл бұрын
Thanks
@goulyethidou97073 жыл бұрын
GE should have had a recall...
@Bigmanfromtexas4 жыл бұрын
Best way to fix a ge dishwasher is to remove it and install an LG
@CaraL-sr4pl3 жыл бұрын
LOL, I was just thinking I will never buy a GE again, as someone stated earlier, there should have been a recall as mine is only three years old. Ridiculous to have to do this.
@aschalewbekele3714 жыл бұрын
Can you please share the service diagnostic sheet mine is missing and I could not find it online. Thank you
@JankyShack4 жыл бұрын
What is the model number of your machine?
@victordeleon94184 жыл бұрын
Hey I have same problem, ants on same spot how is that possible? I wish I could send you the picture
@JankyShack4 жыл бұрын
There must be an electrical potential across those 2 points so when the ant connects those 2 spots it frys it.
@Marco-bb7np2 жыл бұрын
After replacing the board it only lasted a few weeks and dishwasher stopped working again 😞
@bellvnv20003 жыл бұрын
Next video, "Volume" , our friend ! 😄
@cherylbarrett13 жыл бұрын
How much was it ?
@JankyShack3 жыл бұрын
Link is in the description, around $96
@goulyethidou97073 жыл бұрын
I bought my GE dishwasher in 2014 for $950 with in a month I started having this problem I never tried to fix - I would press and hold the door for some 30 - 40 seconds that would help But now I am having Problem with door hinges I guess its not worth fixing as this might cost $350 in parts and $250 in labour GE seems to have Inferior & Sub products in every Appliances the make compared to other brands Really sad to see a Great American company with sub products as this
@wrobo2 жыл бұрын
We can thank the politicians for this inferior quality... since GE machines are so cheap to make now, quality has gone bye bye. I do wish there was a big enough movement to bring back, the once great, American manufacturing. Unfortunately, the benefits to stock holders is to make junk amd ride on the GE name. This is very short sighted and GE will crumble like other American innovators... Think Craftsman, Black and Decker, DeWalt, to name a few. I do believe we would pay a bit more for quality Instead the majority of us will buy on the description placard and brand name... Anyway, sorry... this is a really good video, and helped me through my repair... thank you!!
@l.leefreeman21483 жыл бұрын
Parts on newer MADE in C dishwashers by Haier /GE no break in 2 years not 10 or 12 like it used to be, Next time I am going to get a a Kitchen Aid or another brand, I am done with these things that dont last more then 3 yrs
@janteal65323 жыл бұрын
I HAVE POWER TO MY DISHWASHER BUT ONLY THE TWO LIGHTS ON THE LEFT STAY ON ALL OF THE TIME. THE REST OF THE PANEL IS OUT..
@JankyShack3 жыл бұрын
Open the door and remove the screws at the top that holds it onto the counter, then pull the machine out and look for a paper that tells you how to troubleshoot your machine.
@zaneyd57814 жыл бұрын
I found ants too!
@zulumax13 жыл бұрын
3 year old dishwashers all with the same problem, hmmmm, You think GE is watching this? Be curious to do a autopsy on one of those boards to see if it is a common failure part. Anyone ESR those capacitors? Could be a $2 component
@bettytatum44454 жыл бұрын
Don’t really like LG anymore. Bought a sidekick washer and had it for 4 months and they would not replace it. During the 4 months they just kept sending parts for repair. The thing was defective. I had bought a Best Buy warranty on the original purchase and they provided a new washer. Not buying LG anymore.
@stonecreekmasonry92823 жыл бұрын
Had the same problem with my dishwasher. Ran the diagnostics on the door latch. It was good. Disconnected the power for a few minutes, tried it and it's working. Will probably order a mother board for the future. Really appreciated your research and video. Thanks