How to fix your Nespresso vertuo next coffee machine

Step by step on how to fix the Nespresso vertuo next coffee machine. It turns red after the pumping and does not comes out the brewed coffee.
#coffee #nespressovertuo #nespresso

[@RafaelGrande-q7b]

absolutely fantastic!!!! I had seen other videos about air in the system and I tried may things...... but watching this video I only went with the tooth pick thru from the outside and was enough to unblock the nozzle!!! No need to put anything a part.

[@nalnajar95]

the toothpick worked! 👍🏼 thanks!

[@nikos65738]

Thanks it worked !

[@hufsa1607]

Note: the newer versjon has torx tamper proof screws

[@vinsanityguitar]

Nestle is famous for being extremely low end low quality products. But I'm on like my fifth machine. This is absolutely ridiculous.

[@sabbilon4542]

Our machine has the tamper proof torx screws too. I was able to fix our machine by just repeatable injecting water up the nozzle shown at 3::14. I used a Dental Irrigation Syringe I kept after wisdom tooth surgery.

[@pavluchenkoa]

Very helpful, thank you

[@silverfox1234]

Thank you for guide. Nespresso tech support told me to use a toothpick to push up that nozzle. I wonder if that broke the rubber cup.

[@gudvooy2]

Maybe. But you can take a look and see if you punctured the rubber cup.

[@ldavenci]

I'm trying this right now!!! Update you guys in a few....

[@yairocx]

Did you fix it?

[@ldavenci]

@@yairocx Sort of.....it did give a bit of pressure again, but still had and issue which I discovered was the pump. Nespresso sent me a new machine when we went through their validation process.

[@dese94]

Thank you very much. it helped and now it makes coffee but when I tried to run the rinse cycle it got stuck, still makes coffee though, thinking to by the descaling and run that cycle. Thanks anyhow it was totally not working

[@viper16vet]

How did you remove the plastic round housing where the lock lever is? I removed the two screws, but it seems something is still holding it together in the front. In the video, that step is edited out, you show only sliding it away. Thank you.

[@gudvooy2]

There is a little hook that holds it. Find it and will get that up.

[@viper16vet]

@@gudvooy2 Thank you for getting back. I will try that. It appears that it's down deep inside.

[@vinnydidonne9643]

Im did everything but notting go good , no coffe coming out . Can you suggest something else to do please ?

[@gudvooy2]

@vinnydidonne9643 check the heater if it's working, if the heater doesn't work It wont make WATER comes out.

[@hakimolemecano509]

Nice thank you, i have a similary problème, i gote see this if result may problème.

[@crisrenedenopol8101]

Sir, thanks for the guide. May Vertuo next din po ako, and sinunod ko yung guide nyo para mabuksan ko yung machine. Kaso, yung issue kasi nung sa akin is di ko ma-lock yung latch. Gusto ko sana tanggalin para makita ko ano yung naka stuck dun sa loob. Pa guide naman ako sir papano. 🙂

[@gudvooy2]

Baka po disaligned yung pagkakalagay.

[@jonathanosullivan2418]

Does the light flash red twice?

[@gudvooy2]

No

[@Naamah75]

What type of Torx screw is it?

[@gudvooy2]

If I'm not mistaken it was a T2 or T3

[@Naamah75]

@@gudvooy2 it's an antidamper torx (at least for my machine)

[@jesussalazar1806]

Cuál es la medida del desarmador que utilizas

[@gudvooy2]

Aquí en mi país solo el Philip screwdriver.

[@roxanne2768]

What size screw driver you using?

[@gudvooy2]

Just a standard Philip screw driver.

[@user0password]

I still can not take the cover off 😢

[@gudvooy2]

A little more force

[@user0password]

@gudvooy2 thanks 😊

[@shelby50411]

does anybody have one of these that wont go to solid white...then 2 red blink?

[@gudvooy2]

Sensor failure or maybe heater problem

[@shelby50411]

that was my guess..or maybe a bad thermal fuse?..however when i try to do a factiry reset it does not go to solid white too

[@gudvooy2]

@shelby50411 Well I think the board might be the problem

[@shelby50411]

maybe..or bad firmware..i dont have wifi so i am not even able to try to update firmware...im thinking it could be a blown thermal fuse to the heating element or bad heating element

[@BlueMounee]

Mine blinks red twice and its for reader problems, common with VertuoNext and usually happens when the warranty has expired.

[@C_Franc2000]

la cafetera, no reconoce las capsulas le pulso, se escucha el motor girar, pero aparece luz roja ,un segundo y luego luz,verde,le vuelvo a pulsar, y luz roja ,otra vez,... a alguien mas le pasa???

[@gudvooy2]

Necesito ver el video

[@C_Franc2000]

@@gudvooy2 gracias ,por tu ayuda, te describo lo que pasa, todo es normal, luz verde, se calienta, funciona todo,modo limpieza,modo descalcificar,se reinicia, todo ok metes una capsula, cierras, le das a hacer cafe, y durante unos segundos,se escucha el motor girar,y que intenta leer la capsula nueva entonces, error,luz roja, durante un segundo y se vuelve a poner verde y no detecta,ni una sola capsula, da igual el modelo

[@gudvooy2]

Parece tiene problema el motor de la bomba o algun sensores que no funciona. Asegura que los tubos pasa el agua sin obstrucción. También los switch se esta bien de contactos. Mira la entrada del agua y asegura que el cubito de agua sale bien, prueba la con empujar la válvula. Espero que te ayuda algu.

[@C_Franc2000]

@gudvooy2 nada,no funciona nada Creo que el lector de cápsulas no funciona Le está pasando a muchos,lo mismo Modelo vertuo Next, y plus Todo funciona, excepto hacer café No reconoce la cápsula

[@gudvooy2]

Que pena. Tengo que investigar esa problema.

[@oskarzabaleta3098]

Una pregunta....Donde está el sensor de lectura de la cápsula??

[@gudvooy2]

No tiene sensor

[@oskarzabaleta3098]

@@gudvooy2 Y como lee las capsulas??

[@rockislandlife6383]

Is that coffee in the hole?

[@gudvooy2]

Yes it was

[@brianbell4106]

Water flows out at side, of hatch, keeps happening, what a mess it leaves.

[@DjangoThunders]

After reading so many of these comments I have come to the conclusion that we have all been ripped off.

[@gudvooy2]

This model has a major deffect

[@jafek5]

Video is not good. No mention of tamper proof torx T10. This is a pretty uncommon bit, should mention at start. Also at every disassembly point after removing the screws there are also hidden clips holding the cover in place. But instead of pointing out the clips, showing their location and how to release them, the author does a video cut, skips the step of releasing the clips and just shows the cover coming off easily. Not even a mention of the clips. Actually the main thing I need from the video is where are the clips and how to release them, the screws are pretty obvious.

[@mateoelboricua]

Hi. Trying this now. Would you be able to point out where the hidden clips are? I've been searching but don't see them.

[@gudvooy2]

Just a bit of force and It Will losen the clip

[@Brenda-m6b]

I have two. Neither of them work. Pieces of crap. I tried everything to get them going.

[@gudvooy2]

Do not buy these models. So many problems after 3-5 months in a daily use.

[@gudvooy2]

Sell it to me so I can reuse some parts of it

[@Brenda-m6b]

@gudvooy2 iI assumed that since they were made in Hungary and Ukraine, they'd be better than junk made in China. Do you really want them? Are you in the USA? I'd have to see what shipping is.

[@gudvooy2]

@Brenda-m6b I am in Spain buying deffective staff and fixing them. I am buying from the App "wallapop". The shipping from the App is inexpensive. If you can publish to the App share to me the link and I will buy It.

[@Brenda-m6b]

@@gudvooy2 I'll see what I can do

[@TimMcTim1888]

The amount of moldy crap that must get in there 🤮