How to Install a Carpet Runner On a Spiral Staircase. Heres a Quick Video to show how to install a carpet Runner on a spiral or winding staircase. Any Questions please leave in the comments down below
Пікірлер: 24
@barrygraham9040Ай бұрын
Hi Keith, I'm a carpet fitter in Ireland, I would never get away with that way of fitting here, we always use gripper,(short pin), double sided tape on the tread edges and never use electric staple gun unless every stair is being bull nosed, different countries fit different ways I spouse, anyway not a hater just letting you know how we do things over yonder, keep up the good work and don't staple your finger👍👍
@KeithShannonDirectCarpetАй бұрын
Appreciated
@matlane84954 жыл бұрын
Fantastic work!
@KeithShannonDirectCarpet4 жыл бұрын
thanks again
@kannanaiyar52913 жыл бұрын
Very good explanation. Gives me some confidence to try it. It would have been helpful if there were a close up shot showing exactly where the staples are, such as how far from the cut edge, and what angle, and whether they are going into the riser or into the underside of the tread below the bullnose. Also the size of the staples to use. For those of us who have never used a staple gun before, that would be good to know.
@KeithShannonDirectCarpet3 жыл бұрын
Good questions I will make another video showcasing a little closer angles on that
@kannanaiyar52913 жыл бұрын
@@KeithShannonDirectCarpet Thank you.
@KeithShannonDirectCarpet3 жыл бұрын
@@kannanaiyar5291 you are very welcome
@waynenotley3 ай бұрын
Hi there I live in a 2nd floor flat but has a spiral staircase literally about 6 steps, then goes to a square landing thrn more steps going down but has about 5 funny shaped spiral sections more than what you have done in video... I've used staples but this shows everywhere when I have put carpet tiles down not carpet. Is there any easy way to do the curviture sections using carpet tiles.
@nabihaht Жыл бұрын
My staircase is in a U shape type, so the angles are bigger, i fitted the straight bits but i'm stuch with the curved steps
@KeithShannonDirectCarpet11 ай бұрын
If the stair is to much of a turn you will need to template
@sabrinafisher44173 жыл бұрын
so I have a curved staircase with a stair width of 40" the step is 10" on the narrow end 14" on the wide and the riser is around 7" Can you please help me on the amount each carpet square should be per stair and also the angle cut I need to do ? thank you :)
@KeithShannonDirectCarpet3 жыл бұрын
Sabrina Fisher the angle cut will depend on the curve! But inch1/2 is a good start ....just plus or minus depending on the curve😀as far as carpet, usually allocate for curved stairs 26 inches. Standard runners ...are 28 inch wide to 32 inch wide ..just depends on how much wood you want showing on each side!!! So if I was doing this runner at 30 inch wide I would allocate 30 inch wide by 26 long! Just check you longest measurement and you should be ok!!!! Send me a picture of your staircase and it will be easier for me to judge😀😀😀😀😀
@maiconassis64 жыл бұрын
Great, I have question. How do you get the measures?
@KeithShannonDirectCarpet4 жыл бұрын
Which ones?
@maiconassis64 жыл бұрын
Spiral staircase
@richardblack41252 жыл бұрын
Keith can you show if you put carpet on turns without taking the inch cut off how much the carpet would run of the bound edges
@KeithShannonDirectCarpet2 жыл бұрын
I can!
@richardblack41252 жыл бұрын
What will video title be 🙂
@KeithShannonDirectCarpet2 жыл бұрын
Not sure yet
@richardbaxter85844 жыл бұрын
Do the staples show?
@KeithShannonDirectCarpet4 жыл бұрын
Richard Baxter I bang them down and clean up any that are showing as best as possible
@tonybutler95233 жыл бұрын
Staple city
@KeithShannonDirectCarpet3 жыл бұрын
Staples are needed for that carpet definitely 😂😂😂😂