How to Install Fuel-It Ethanol Content Sensor in B9/B9.5 Audi S4, S5, SQ5, or RS5! | 034Motorsport

[@roderickwilliams9605]

perfect timing! love 034 products!

[@icecubeninja7932]

Thank you!! Much needed! Hopefully this with the other E85 video you put out will be enough to stop all the questions on your Q&A livestream 😂

[@034MotorsportUncut]

We can only hope.

[@_Imlazy]

Which vehicle is in the video, there site has nothing for the S5B9 is this one of the universal kits and is so could you link which one?

[@SIMPLB9]

How many clamps should I order?

[@andytran-ry7yc]

how safe is 034 stage 2 e85 on the b9 s4 because i heard it’s not good to run during winter time but im in california and at night its around 50 degrees so should I keep running e85 or can I do a blend?

[@034MotorsportUncut]

Full E85 won't be an issue in California. As long as ethanol content levels are between E60-E85, you won't have an issue!

[@6492002]

Thx for that vid!

[@034MotorsportUncut]

Our pleasure!

[@BryanSchulta]

I see there are 3 GM sensors to choose from. Which one did you use?

[@034MotorsportUncut]

a.co/d/c4g5ERc

[@CoachD4]

*easiest safest cheapest and now we have INSTALLATION VIDEOOOOOOOOOOS*

[@034MotorsportUncut]

Installation videos make the world go round

[@aznspc]

The link you have for fuel it, don’t need to add on a flex fuel sensor right?

[@034MotorsportUncut]

We provided a link in our video description for the sensor needed. You can find it here: www.amazon.com/ACDelco-13507128-Original-Equipment-Sensor/dp/B073ZQ1G2P

[@dongramlich3331]

What is the purpose of selecting the GM flex fuel sensor?

[@034MotorsportUncut]

These are the sensors that Fuel-It requires for their device to operate properly.

[@dongramlich3331]

Thanks!

[@ryanf7320]

Is there an instructional video for a stage one flash? Other videos on line seem to skip some steps. Thanks

[@034MotorsportUncut]

Shoot us an email at [e-mail] and we can assist!

[@newlyboyer1206]

With the positive wire connected to the positive terminal block, will it deplete the battery over time?

[@034MotorsportUncut]

It will not, this is how Fuel-It recommends wiring

[@henrycervantezzz5566]

Where do I get these bundy connectors? Thanks for the great video!

[@034MotorsportUncut]

You can get the bundy connector on Amazon, or your local auto store!

[@robp696]

So you don't recommend finding the fuel pump fuse and letting the car stall out to relieve the fuel pressure?

[@034MotorsportUncut]

It is not required as shown in the video. By loosening the 14mm flange nut and allowing pressure to bleed there, it allows for much less fuel to come out when removing the rubber hose.

[@robp696]

@@034MotorsportUncut thanks

[@fishingstix610]

Is it safe to not install the sensor and just wait 10 minutes after fueling up with e85 and reflashing?

[@034MotorsportUncut]

It's not something we'd recommend doing.

[@henrycervantezzz5566]

I can't find these clamps at local auto stores, which ones do I need to order on Amazon? They give two clamp sizes, one open and one closed. I'm lost haha.

[@034MotorsportUncut]

These would work: www.amazon.com/Oetiker-Stepless-Size-Clamps-Single/dp/B01GTWLXCQ?th=1

[@henrycervantezzz5566]

@@034MotorsportUncut ok great thanks cause the sizes they sent me with kit are 15.3mm and 14.8mm. fuel it Website says it should work with 5/16 inch hoses. I'll give them a shot first unless you think I'd be wasting my time. Cheers!

[@LeCatCation]

Can I use normal hose claps?

[@034MotorsportUncut]

High-Quality hose clamps of the proper size can potentially be used.

[@abe96yo22]

Where can I find this fuel it sensor ??

[@034MotorsportUncut]

It is linked in the description, as well as all of the other components.

[@aaautosport]

New to Audi stuff but I have a B9 SQ5 I'd like to put on E85. So the ethanol content sensor doesn't wire into the ecu for datalogging, flex fuel maps, ect like most cars its just strictly for a gauge im assuming? My other vehicles are on E85 with GM content sensors so I know all of my local pumps are 70-75% on average. Knowing that information should I even bother installing another sensor?

[@034MotorsportUncut]

Installing an ethanol content sensor is 99% for peace of mind and ease of switching fuels. With the sensor, you can tell exactly when your car is ready to switch to or from ethanol.

[@aaautosport]

@@034MotorsportUncut gotcha thanks!

[@1ORiOn9]

Any part numbers? Links? Fuel It has 2 DIY kits, wich one is it? The GM Ethanol Content Sensor is the one that Fuel It use right?

[@034MotorsportUncut]

Check out the description!

[@quickhandcam8596]

Is there a reason you guys used Oetiker clamps instead of just hose clamps that are screw down, like what's on the intercooler piping, for example? EDIT: ( 2:25 ) Also, where you did you get the brown connector? Does it come with the Fuel-It analyzer or do I need to buy that separately?

[@034MotorsportUncut]

Oetiker clamps are the only correct clamp for EFI fuel lines like these. Generic hose clamps are not safe for use in applications like this. All wiring connectors were from Fuel-It

[@pollorobot69]

This Line Is Always Active? This Not Bad For The Sensors Always On

[@034MotorsportUncut]

This does not negatively impact the sensor

[@pollorobot69]

@@034MotorsportUncut Thx E85 Have Best Price Result For This Plataform

[@torresrobertt]

Does someone have the part number? Or a link to the product?

[@034MotorsportUncut]

Check out the description!

[@SIMPLB9]

@@034MotorsportUncutwhat do I press for “add a flex fuel sensor”

[@Dop3Mojo]

easy enough 🌚

[@034MotorsportUncut]

Very easy! As easy as gaptizing a GT350 one might say :)

[@Dop3Mojo]

@@034MotorsportUncut that was a great midnight snack 🥱