How To Install Locking Drawer Slides

[@RoughRide]

Put a scap piece of ply on the backside and you won't get the blowout when you drill your holes for the slides.

[@antonioguevara4188]

Or tape it firmly

[@OutdoorChefLife]

Nice, thanks for the video! How do you install the slides on the other side? Can you still use the same type of bolts?

[@jeffreyreichert1609]

I was wondering the same thing

[@SolidWoodWorx]

Yes I actually use the same holes for the other side and do one bolt between two slides!

[@dmwi1549]

Can he use a single bolt to attach both center slides through same hole in center wood divider? Seems logical. Otherwise he’d be using different holes in the adjacent rail and would need to dismount first rail etc. wondering why he bothered to pull them tight, flush with surface if that is the case? Otherwise good info-good timing for my van project. Might be ordering some stuff from your site.

[@Radryannn]

@@SolidWoodWorx what size would you use for this?

[@izabari]

I'm having trouble getting the sex bolts to grab. I got one with the use of a clamp but no luck with the others. Using large bolts with 3/4" plywood.

[@brandonjohnson3120]

Great tips from a true professional. Thanks for the insight on installing the slides, measuring the ID, then building the drawer box. That’s the gold right there.

[@godaniel122]

Hey mate, great vids, thanks for sharing. I do have a rookie question tho. With those bolts you're using, how do you drill the slider rails on the shared plywood wall without hitting the bolts of the other rails on the other side, if they are both located on the exact same place, only on the other side of that wall. Thanks a bunch!

[@LilyWasHereMB]

I prefer the names barrel bolt or Chicago screw but hey, sex sells

[@yoojesss]

SUBSCRIBED. Dude, hands down. BEST YTuber. No BS, straight to the point, step by step!!! Good job man! Keep up the good work! 💪

[@photog1529]

Nice work. I use long paint sticks to shim my drawers...these give about 1/8" clearance between the drawer bottom and base and pretty much support the entire length of the drawer bottom. I do like those sex bolts though...the screws that come with drawer slides are pretty useless. One suggestion...maybe consider using a flat washer on the inside of the drawer to keep the screw head from crushing the plywood...doesn't look like the screw flange is wide enough.

[@williamlucrisia9169]

Hey Brother, nice work. I get all that part... Perhaps you could do a vid on the drawer front detail. How you go about getting the slide lever through its face. Again nice work.

[@alwaysbepreparedwithjeff3245]

Thanks Again For Sharing Your Life Here On KZbin

[@davidgoulden3543]

Hi great video can you tell me what length sex bolts you use with 3/4 inch ply please Dave

[@SolidWoodWorx]

Our large size available on our website

[@jbk4341]

First of all I just wanna say, this is what every other truck build video leaves out. Thank you so much for going into detail, I’m only left with one question. Do you use the same holes when you install the slides on the right hand side, as well as the same sex bolts or do you offset the installations? For the middle “1” by”.

[@SolidWoodWorx]

I sandwich the drawer slide/wood/drawer slide with the large sex bolts!

[@jonlangley7584]

Super helpful video! Thanks man! I'm installing the 56" version and I'm not gonna lie I was pretty intimidated before watching this!

[@ArielleSea]

Amazing tutorial, man. Just what I needed. Thanks for all the tips throughout. Many KZbin videos skip explaining what drill bits and shims etc that they're using, assuming we know. Thank you!!

[@dianemora3602]

Thank you! The instructions that came with my slides were useless -- this is exactly what I need

[@andrewschwartz_]

couldn't have posted this at a better time, Im building my platform for my 4runner tomorrow. thanks for the video!

[@toyostormrider1311]

In the planning stages in building my own bed storage boxes,etc for my Hilux, thought I'd see what's out there on you tube,yours set up in my opinion are the best going round, thanks for sharing. Greetings from West coast down under

[@pambansangprobinsyano7923]

What the name of that bolt you used for slide locking drawers bro

[@SolidWoodWorx]

Sex bolts on our website

[@RotasOpera]

My drawer on heavy duty slides locks closed, but won't lock open. Any thoughts on what is causing this?

[@SolidWoodWorx]

You want them to lock fully extended?

[@RotasOpera]

@SolidWoodWorx Yes, exactly!

[@Luxman35]

Great video! Really like the sex bolt idea. Question I have in this video you, you installed the locking drawer pull, for the left side of the box, when installing the drawer for the right side, the middle locking slides do you use the same sex bolt to attach both rails

[@BenjiWhiskerBiscuit]

Solid video and hardware! Every other video had removable slides. Thanks for demystifying the installation of the non-removable slide types. My only issue that a single pack of sex nuts only provided 1 nut supporting each far corner of my 56" long drawers. With the extreme wait of it loaded, I wanted to add additional hardware. After buying another pack of sex nuts from your site, I now have 2 points in each corner, but now my drawers were binding on the nuts before the last lock could be engaged. I isolated the issue being the hardware installed in the middle of the inner box. Without the middle nuts it works fine. I already have holes in the wood at this mounting location, so I would like to make it work. Is this expected behavior with some of the mounting locations on the slides? Is there variations in the depth of the sex nut head (my digital caliper seems to think so)? Also the bolt side seems to have a slightly bigger head then nut side, so best to put the more flush head (nut end) in the metal and bolt side in wood (as you demonstrated). I may try to grind away some layers of steel off the nut to keep it from binding, before trying other hardware. 14/16 nuts installed operate great! Drawer works so I'm a happy customer. :)

[@jonathanemocling3826]

Awesome

[@robt7165]

Cool I'm gonna make a double drawer so I guess I would need longer sex bolts for the 2slides in the centre maybe some lock tight but excatly what I'm thinking of making for my truck

[@jonnytacooutdoors]

So how do I remove the drawer?

[@SolidWoodWorx]

Once the drawer is installed it can not be removed unless you unbolt it. These 500lb drawer slides do not ave a function to remove the inner rail.

[@jonnytacooutdoors]

@@SolidWoodWorx thanks for the info

[@harrypottah8889]

Forget the slides, I wanna see more builds 🚌

[@wallheadkdir]

Good video. You touched on everything I needed to see..A BIG HELP YOU ARE😊

[@misc.projects3094]

Sex bolts? 🤣 Chicago screws is their real name I believe. Good video!

[@samcotnoir]

Do the sex bolts get in the way of the installation of the drawer on the right? Thinking of the middle support with a drawer slide on each side. Thank you!

[@FROADER]

I have been watching your videos for a while and just finally read the ABOUT ME in the description, and saw you're in HB! I'd love to come by and chat with you about a couple ideas I have for the back of my '97 E350. I'll get in touch!

[@JizzySpeaks]

I wanna make a drawer & a slide out table underneath it. Any help on what I can use for the table

[@markgaudie80]

I want to create sometime similar to have pull out draws under my rock’n roll bed in my Campervan.

[@boothbusadventures6689]

I do not like the locking mechanism on that brand and they always come banged up.

[@sa-iw4dr]

Those "Sex Bolts" really look like they make those drawer slides extra sturdy and the finish look clean and nice. I don't work in wood but I can tell you know your medium, this is a art form. Where do you get those U shims, those where nice, I guess you would have to make sure to make your inside of the drawers that much shorter, when planning your build. Excellent!

[@transitvandiego]

Thanks dude, I learned a lot! Avcrig lol... yeah I have their rack on my van.

[@patricktompkins5704]

Solid video. I have some of your plans for a 1st gen 4runner box. My only question is How do you install the drawer slide on the opposite side without interfering with the first slide?

[@SolidWoodWorx]

You sandwich the center jam with two slides and a bolt through all of them

[@justinbelote1768]

Do those sex bolts stay tight? Or would you recommend using loctite? Im Going to build drawers for my camper storage and I’m wondering if over time those sex bolts will loosen.

[@SolidWoodWorx]

Loctite is always a good idea!

[@JoeTirone]

So you've got one slide in. How do you make sure the next set aligned in the middle doesn't interfere with the mounting hardware for the first? Are there offset holes you can use so avoid the overlap?

[@SolidWoodWorx]

When i do that i bolt through both slides and sandwich the wood int he middle

[@JoeTirone]

@@SolidWoodWorx and the sex bolts you sell would be long enough to go through what thickness on that center board?

[@izabari]

@@JoeTirone I got one set of bolts to bite but didn't feel comfortable enough with it. So I went to a big box store and grabbed some longer bolts. Couldn't find exactly what I needed so I bought very close to what I needed and grinded the length and took a die to get the bolt pitch reestablished.

[@sherilucas6025]

Great video! I’m curious how you attach a drawer front when using locking drawer slides?

[@SolidWoodWorx]

I cut little holes out for the tabs to go through

[@billshorter666]

@@SolidWoodWorx Do you have pictures or a video of the finished product?

[@trumpwon8231]

Amazing what money can buy and build. Looks great

[@calebphelps1836]

Very nice u should make video for nissan rogue 2011

[@arturasaranauskas6386]

Thank you for great explanation

[@mwet2u2]

It looks like you are setting up to put in another drawer. Are you lining up the holes in the other drawers slides? Then you are through bolting them. I just got my slides and thats where im at.. Thank you for the video.

[@SolidWoodWorx]

Yes I am

[@Smithy-br2pl]

Love the little drawers in the background the set of 4 or so should show how to make them

[@Ron9257]

Excellent video. Thanks for sharing..🏆

[@mayatuinstra2032]

is there a soft close option for the locking slides? Any recommendations on how to add soft close feature if no existing hardware for it are out there?

[@SolidWoodWorx]

There is not

[@taliesinangling3564]

Your workspace is immaculate

[@petercourtney-c3r]

If your draw slides are the same size as the cavity space what clearence would you leave at the rear of the draw to allow for correct locking?

[@SolidWoodWorx]

At least .25” I usually allow

[@markhiggins3054]

Bloody good - I have 2 48” drawer slides - what material thickness are you using please?

[@SolidWoodWorx]

3/4”

[@UncleT0ny]

what type of wood do you recommend for making these drawers?

[@SolidWoodWorx]

I have been using a plywood called luan, it’s lightweight and strong.

[@garyferguson1552]

Great Video Trying to build a drawer system in my 2023 2 door Wrangle. Is it better to install the slide at the bottom of the drawer or middle?

[@SolidWoodWorx]

Bottom

[@webstuff56]

Hello and thank you. I'd like to see how you put together a ultitiered drawer--you know like where the first half of the draw slides out and then a second below that follows. Thank you

[@ArielleSea]

+1 this would be awesome

[@DaleHawkins]

Wait, where can I get those sex bolts? 😂. Thanks for the video. I am planning to make some of these using your plans and probably the hardware from your website (including the sex bolts!). Thanks again for sharing all these excellent tips!

[@SolidWoodWorx]

You can find the sex bolts on my website www.solidwoodworx.com

[@andrekrausz2407]

Thanks. I need to install mine into a closet, so I would be drilling into the studs in the wall, as opposed to a cabinet. What do you recommend?

[@SolidWoodWorx]

Long wood screws

[@alexross4062]

So how would you go about doing the second drawer slide on the opposite side? Would you just use a slightly longer male bolt to have it go through starting from the drawer slide on the right, and into the female bolt on the left drawer slide with a hole in the wood in the middle?

[@SolidWoodWorx]

I would essentially sandwich the wood between two drawer slides so yes a large sex bolt i sell on my website will work with a drawer slide on each side of the 3/4" center jam.

[@Nathanielpaisley]

hey man, I just bought the 6ft slides for $250 for my van and one came damaged. like it was dropped on the locking lever side. Any idea how to fix it? Meaning do you know which part exactly is bent? Any help is appreciated. Thanks man

[@SolidWoodWorx]

Email [e-mail]

[@patriotsleepercell4060]

The lenght of your slide need to match the lenght of you drawer?

[@RobbyT1994]

Are those sex bolts long enough to install 2 side-by-side drawer slides through the same 3/4" plywood? What is the diameter/length of those bolts?

[@SolidWoodWorx]

Yes

[@jacinto042568]

@Solid wood worx Hello, about the shims, what so much space do you recommend?

[@SolidWoodWorx]

Hello What do you mean about this?

[@Espinal_424]

On some of your builds I see that you turn a pair of locking slides into singles instead of doubles like this video has. Do you have a video showing how to install one locking slide on each drawer instead of having two per each drawer?

[@SolidWoodWorx]

Hello Luis, I do plan on doing a video on that soon!

[@danchamp7938]

Hey I was wondering if you have had any issues with the Vadania drawer slides? I hear mixed reviews for them

[@SolidWoodWorx]

I have had minimal issues with them. To be honest all of these slides are so similar from similar factories.

[@ryanskeete]

Have you had any issues from customers regarding slides failing? Also curious if the Vandania have stainless steel ball bearings?

[@SolidWoodWorx]

I have very little problems with the slides i sell, they are chrome plated steel ball bearings.

[@jamiedouglas2809]

Nice work Mate, loving your vids from over here in Aus, any chance of a quick video on your Kreg / Hidden screw jig and how it works, such a good concept but not widely used over here. 👍🏻

[@SolidWoodWorx]

I wouldnt have time to get a video on how that works but im sure there is one out there. thanks for your support!

[@reneeserrichio1616]

I currently have a 4Runner and love love your 4Runner Platform with drawers… thinking of going to RAV4 prime and would love to see you do a build on any RAV4. Thank you 🙏🏽

[@SolidWoodWorx]

Hoping to have somehting for the rav4 by summertime!

[@malcolmhay6668]

Thanks Brian exactly what I wanted to see.

[@system2thinker659]

Excellent attention to detail sir, thank you.

[@NWbirdseyeview]

Is there a top and bottom or can I install these so the locking mechanism is unlocked when pulled up?

[@SolidWoodWorx]

You can do that but then if you pull the slide out it won’t lock open because gravity drops this little lever in the back

[@jake8286]

I will be building your 5th gen 4runner drawer system. Will the latches on the locking slides stick out too far to close tailgate?

[@SolidWoodWorx]

No

[@paulsanders1]

Thanks Brian, you have mad skills!

[@brei1138]

nice! but how do you do the other side slides?

[@maxbojorquez663]

I’m guessing you just use the other holes available but I’m wondering the same thing!

[@user-bw5xf3yr3m]

I have a question , with these locking draw slides how to you disconnect the slides so I can remove the draw box? The draws I built are very heavy and assembled and need to remove draw boxes to make it lighter so I can carry it into my truck.

[@SolidWoodWorx]

You cant

[@lukeagex]

Most of these slides allow you to disconnect the inner rail by depressing the locking levels when the slides are at full extension

[@corgilover3011]

Great video.. love the shop. So if you were installing a drawer in the other side as well, would you use the same screw to hold the opposing drawer slide?

[@SolidWoodWorx]

Yes

[@roneykaithpalmaria]

Could you buy a pair of locking and a pair of non locking? Then use one on each side? Would they still lock?

[@SolidWoodWorx]

Yes, on my website you can also purchase them one side locking

[@timperkins716]

Awesome work!! I wish I’ve seen your videos before I started building my drawer system lol

[@deanharris2240]

It looks like you drill pocket holes for the drawers. Do you use pocket holes for box carcass too?

[@SolidWoodWorx]

No I just do this to attach the drawer front so you don’t see the screws in the front

[@mathewjon9329]

You are so bloody good at what you do mate

[@FakePersonna]

Thank you! Awesome tutorial.

[@name.terrie]

Great video, info, and tips! Thanks so much!

[@norsefalconer]

Thanks for sharing the hardware recommendations.

[@mediaupload]

Thanks for the video, the level of detail and the parts you used. This is very helpful.

[@jblyth22]

Very glad I found this video. I’m using similar slides for a completely different application and I think your method will work perfectly for my project. Well done. One question: what type/size plywood did you use for the box construction and drawer bottoms? The bottoms look super clean and I would like my project to have a similar look. Thank you very much.

[@SolidWoodWorx]

The uprights are 3/4" and the bottoms are 1/2"

[@barrypendley8814]

What lubricant do you recommend for the slides?

[@SolidWoodWorx]

I use a silicone spray if you think the lube that has come on the slides is dried up

[@tannerwade7823]

When you have a slider on each side of the divider, do your large sex bolts reach though both of them? Or how do you go about attaching them if the holes are lined up?

[@SolidWoodWorx]

Yes they do

[@brucesinclair9628]

Hey Brian, just sub'd to the channel, really like the content and how you discuss it. I know you mentioned that you are going to be doing some styles for Jeep wranglers... Any idea when you might be pushing those out :) ? I'm in the middle of changing/redesigning mine and would love to see what you have come up with... basic thought was pullout for 2 burner camp stove and fridge on top same side as the driver... I just have to many "options" that I'm thinking of and have stalled... LOL Thanks

[@SolidWoodWorx]

I have not done one yet

[@brucesinclair9628]

@@SolidWoodWorx No worries, just seeing if it was something you haven't yet released because you are busy. Keep the content coming... I'm enjoying it!!

[@chrismassie9894]

Question? I am building something similar and when you install the slide to the center jam. How do you install the one on the opposite side? Also could you use those sex bolts to install both the center slides?

[@SolidWoodWorx]

That’s correct

[@barrackobama3804]

Thank you chief

[@izabari]

Brian, great video. I have a question. I purchased the 56" 500lb drawer slides. I have the first and last holes drilled and sex bolts installed. However, the middle hole is only approximately 6.25" from the front hole. Do you just drill another hole at the halfway point or am I missing something?

[@izabari]

I also see a hole around 15.5" from the back hole. If I did all 4 holes it would leave an unsupported length of around 29". I assume this is okay?

[@SolidWoodWorx]

Hey Michael in that long of a slide I would do 4 holes for sure!

[@izabari]

@@SolidWoodWorx sounds good. I ended up going with 5 bolts. I had to drill through the slide as you had mentioned. Thanks for a quick reponse.

[@jpeg.verification]

A+ tutorial Brian!!!!

[@timbrown7980]

Wow you do nice work!

[@jakkob489]

Legend cheers for the tips

[@chromaticvisionstudio5489]

Chicago screw

[@kenmarapese9085]

Good vid, well produced.

[@achekspir]

What lenght are these sliders? For reference. Thanks

[@SolidWoodWorx]

36"

[@seekingthestokewithneeks6640]

Hey man, thanks for all this info you share. Going to be building a setup for the rear of my 4runner really soon and had a question. How should you determine what length of drawer slides to use? Should you go with as long as the drawer is going to be or as close to that as possible? Sorry if there is any confusion, I hope I worded that properly.

[@SolidWoodWorx]

Check out my plans and hardware on my website www.solidwoodworx.com should give you some more info

[@danielmedina6864]

What size sex bolts did you use? Are those also called Chicago bolts?

[@SolidWoodWorx]

Not sure never heard that Chicago term. I sell them on my website.

[@danielmedina6864]

@@SolidWoodWorx Ok I had never heard of sex bolts but they look like Chicago bolts. What size are the sex bolts that you sell on your website? It doesn’t say the dimensions.

[@timbior]

Very cool Video!

[@roar-films]

My question would be how to mount the slides on the next side using sext bolts if the other side is blocking access

[@SolidWoodWorx]

You use 1 bolt for both slides i was just trying to show the concept

[@msoomro0001]

Great video. Learnt a lot. One question. How would u install the LEFT rail on the Right hand box since the sex bolt position will be the same on the center separator. Where the right rail is for left drawer Thanks

[@ThisTall]

This was helpful? Something I like to do to prevent blow out in high end Plywood like this, is start the hole with a self centring 1/16” hinge bit, then finish the hole all the way through with the 1/16 bit, and then pre drill with a Forstener bit from the back side just as deep as the screw head. (Probly just 1/16) then drill the main 5/16 hole.

[@santiagora89]

Great build! Where can i get those the sex bolts?

[@SolidWoodWorx]

On my website www.solidwoodworx.com

[@user-bw5xf3yr3m]

Can you put rails on the other box to the right now that the middle plank has a track on it?

[@SolidWoodWorx]

When i do that i bolt through both slides and sandwich the wood int he middle

[@user-bw5xf3yr3m]

@@SolidWoodWorx thanks and really like the videos and information you present

[@Niafifia]

Thank you!!