How to install pistonrings on a twostroke

[@kyne96]

cant thank you enough, spent 20 hours on my bike racking my brains and i think ive found the solution! my pison rings had no gap in between and they need a .24mm gap. thanks!

[@Nine-Signs]

you sir, are a legend. between your vids and my Haynes manual I have been able to rebuild my speedfight engine and save myself money. Thank You.

[@mikerowe7822]

Thanks for showing that third ring how it goes under the lower ring, no one seems to show this, its very helpfull.

[@berticusmaximus00]

Thanks, I was assembling a leaf blower and cracked the ring so I got another one and thanks to this vid I didn't break it. :)

[@DJeimaXe]

Best video than ANYONE ELSE in KZbin; thank you.

[@NorthSurvival]

Hello, I have a problem, I have a Peugeot Speedfight 1 100cc that recently seized up/heat seized. It was not tuned. I then changed the cylinder, piston etc. It now starts up right away, but after a while it dies all of a sudden (as if you had turned off the key) and then I can start it right up again, this usually happens when I go over 60 km/h or uphill. When I changed the cylinder etc, I also cleaned everything thoroughly, such as the carburettor, intake, new air filter, new fuel filter (there was no fuel filter before) new spark plug. I also removed the oil pump and put a metalplate with a gasket over the hole instead, I now mix the oil directly into the gasoline. Some other info that might be important. - When I drive over 60 km/h, it starts to make a noise from the variator (CVT), it´s sounds quite a lot. - When it died, I tried to start it again while it was rolling and then it started right away, but it made a noise from the variator, like something "let go" that had been seized up, like a rubber sound, maybe from the belt. - The variator belt touches the variator cover on the inside and has grinded a cut in the metal. - In the variator, where the weights are, the belt does not go down to the bottom of the wheel. - The clutch bell had turned blue from the heat. - The place where the connecting rod attaches to the crankshaft had turned blue from heat. - There was no fuel filter on it before. But i now saw there is an internal fuel filter in the gastank, can it affect the vacuum if you now have 2 fuel filters. Please help me. Regards Andree.

[@Raptormotorsports]

Beautiful video man helped alot and got my bike running like new again thanks alot!!!! 🤙🏼

[@Coalemos]

😅😅😅😅

[@watvannou]

Exactly what I was looking for, great video!

[@pauljanssen7594]

Music sucks but I learned that the arrow points towards the exhaust port that way the end gap on the rings is not anywhere near the Southport or the two intake ports. Again the music totally sucks.

[@webmastertaylor]

Really well done, thank you! Very helpful.

[@tombartram7384]

Important! If using the piston in barrel whilst off the bike method on twin cylinder bikes, also fit the inner circlips whilst off the bike. Less fiddly, and anyway when fitting circlip to cylinder 2, barrel 1 would be in the way.

[@christianreynolds1719]

Are the inner circle clips important because I been try to get them in for a while and i can’t really find a way to get them in???

[@hellohello8556]

Quality content. Straight to the point. I subbed. Cheers!

[@christophercastillo1732]

Good video man. Quick and simple

[@dannyweston1]

Great video bud.. Answered my question perfectly👍🏼

[@Stephen.C.]

Nice demonstration. Shame about the infernal row playing over the top of it.

[@angelisone]

A lifesaver, many thanks.

[@mattlong212]

Awesome video. Thanks for sharing your knowledge.

[@chriskirkham-t1c]

So... the darker ring goes on top...and the" v " groove faces up cradling the locating pin thing ?

[@ItsMeGaryG]

Your video is the only place on the web that I found that mentions the "extra" ring that you said goes under the lower ring...what is this extra ring called, what is it's purpose and why does it go under the lower ring?

[@ranaram9942]

Y7rhdxvbjhj9u, mm.

[@jaungarcia9770]

Can u use piston of chainsaw for 2-stroke bicycle motorized engines

[@joegardiner4220]

So which way does the chamfer go on the top ring and does the top ring gap need to be 180 degrees ( as far as possible from the bottom ring gap ) so the compressed gasses take as long as possible to go through both gaps ?

[@225slantsix]

i have a tb60 2 stroke i ordered a rebuild kit and the new kit had the extra ring that goes under the lower compresion ring. but....as long as that extra ring is in place the cylinder will not go on. if removed it works fine but i want to know why it does not fit right and is it safe to run without the extra ring?

[@HasSse666]

Skip the extra ring

[@SDsailor7]

Good video very interesting and informative

[@SDsailor7]

So. what if the piston ring has a letter on it? Does the face up or down on the groove? Anyone know thank you.

[@mocatz187]

Do you have to hone the cylinder to put new rings on. I know you do on cast iron but what about a chrome lined Puch E50.

[@daveking4246]

mocatz187 my stock kx had chrome lined sleeve...I took to a shop to have it inspected before doing a top end and I was told if the jug is not damaged or scored in anyway I can swap rings daily if I wanted to without and honing....comment from experience not technical knowledge

[@theforestlizard223]

I have the samall pice on ring that goes on the last ring and the Piston does not fit with in in place what should I do

[@defectedsoul]

how do i know what piston ring goes on top, this is bugging me, why dont they come with instructions :/ i have the naraku 70cc bore kit, any help on which way the piston rings go would be a great help

[@HasSse666]

Place the darker pistonring on top unless otherwise are specified

[@defectedsoul]

thanks!

[@leosepocado5403]

Where the store can buy a piston and ring...davao city area..

[@mithupalani4465]

Which side the piston arrow comes for max 100

[@thegeneral1469]

Which way is the arrow supposed to point?

[@xy200stii5]

towards your exhaust port

[@LeylaDas-hh6ei]

Kolay gelsin cok başarli bir iş yapiyosunuz

[@HybridEdits]

what if my piston only has one cut in it where you can put the rings?

[@severinoperez8679]

Hola Que tal amigo, desde la republica dominicana, quiero saber para que se le hace eso a la anilla

[@zombiedeutsch]

hi i installed new cylinder kit, but when my scooter idling, i hear ringing noise, just like a worn piston with bad piston rings, what could be the problem please ?

[@calebandresi2041]

Ever figure out what it was?

[@TheUpandoveragain]

Thanks 👍

[@muzza_r]

Very helpful. Doesn't need the music though...

[@MrBerenguer67]

Thks four video a Maine miles need to drive whit new head and piston please thks

[@JoeKickass324]

Cool most people don't go into detail about the teeth on the piston ring thanks

[@francocarrion1031]

Hello dog Very good video Could you tell me what that song is called thanks Regards from Argentina crazy best friend

[@regish759]

Soundhound on Android to find out ;) I'll make it easy on you : "Sa Jävla Bra" by Lillasister.

[@turbotonic27]

thanks very informative video! make more

[@baftijari]

my ring have the little N on in,what's that mean?

[@edgarl.hernandez7]

hassse666 i know that everybody is talking about engines and pistons, actually im about to open my moped and troubleshoot my compression prob. but i want to ask you, who sing that song? i mean they are awesome haha!

[@alishavaizalikhan5284]

Bhai yah Piston Kahan Milega

[@johnkournidakis1914]

Ευχαριστώ πολύ ενημερωτικό !!!

[@FuatFuat-b6d]

Çok güzel olmuş emeğinize yüreğinize sağlık harika

[@JensEskildsen]

Thanks man...

[@HasSse666]

lycka till 😊

[@keithdobbo85]

I have just bought a new piston and rings but one of the rings is a different colour why is this?

[@HasSse666]

so you know which ring to be on top

[@hattiwatti1000]

thanks for the good video!

[@maheshprajapati2912]

Bajaj m-80 engin work show please

[@delltrainer]

very well done.

[@traystunna]

Hella helpful!!!

[@chaneli4855]

Thank you for that...

[@Pstnlss]

Thanks so much!

[@greekgod5193]

Good video

[@franklinbinas6240]

That piston is for dio

[@rajbahorpatel1708]

Please told timeing

[@MrFiddlesticks3]

Crap! my pistons square, I'll be right back......

[@mjshaheed]

lmfao

[@Arbe1945]

Video great but the music is a distraction and not all viewers are young.

[@banburylitho4068]

handy shandy.. cheers

[@alikhan1297]

How to make tillerripper

[@alikhan1297]

My

[@siddharthmane5642]

Very good

[@frizerovshik]

The song is: Lillasyster - Så jävla bra amazing how i found it... actually used a site that listens to the song, identifies it and tells you what it is (midomi dotcom)

[@baftijari]

thank's for answer :)

[@jackdon6737]

Good 👍

[@danielpeinovic9476]

Thanks man

[@PTDQ]

OK , tank you

[@ChiranjitSaha94]

please show me a crosshead piston

[@samankumara8269]

Thanx boss

[@dondupit58]

Nice music boss

[@wukssizoli]

How to break your pristonrings in few steps. :)

[@xzb67vtg57]

That pitston is damaged

[@Ryan.90]

😂 Literally just thought thought that. It's only a bit scuffed, but if you've bothered taking the engine down to that level, might as well install a new one.

[@alimuddinchowdhary7371]

Nice

[@sunilpoojari6458]

Suzuki samurai bike bore kit henna

[@zombiedeutsch]

thank you, no need for a mecanicer to toutch my bike :)

[@draginnl8857]

Thanks! Thanks! Thanks! Now I can spend less time and money.

[@hobocop2585]

Nice music

[@kouamekouakouraphael2259]

Cool

[@vasileoprinca7913]

..not with your thomb!

[@HamidaliHamid-bh8sq]

Kha samala ga

[@aosafali7696]

thanks

[@HasSse666]

Thank you for comment :)

[@samyuel4181]

👌👏👏👏👏👏

[@normangensler7380]

this would be a very instructional video, without the music!

[@GertBowker]

loose the music...

[@oscar102681]

It's spelled "lose" in this instance. Learn to spell, if you dont like this sound turn it down, learn to appreciate and stop complaining online like a fuckin bitch. Thanks.

[@ChristianJoyAzucenas]

+O. Blue Exactly

[@chippygc]

please, turn off that crappy background music! it spoils the video!

[@mazouaoudou8212]

OK moi j'aime trop yamah

[@cougar1972xr7]

lose the music it sucks vid is good

[@munees8022]

Munees waran

[@chaturbhujaranachaturbhuja3687]

Tar buar banda video

[@johnjames77]

The worst Vid ever because of the music

[@TheGoldenSapling]

This is real music

[@randrianariveloandry9484]

slt 47 cc

[@PetterIvarsson]

Tydligt!

[@nastie9903]

That's not the best way of installing a ring

[@garbinsonmawlong7532]

I hate the background music

[@ellieme9226]

another satanistic sound

[@WhiskeyTangoFoxtrot1911]

Thanks man,