How To Make 100Ah From Old ATX Power Supply - Fast And Verry Simple

[@LongTechnical]

If you have any problem contact me on facebook i will help you. Thanks for watch my video: facebook.com/thanhlong.pham.33234 If you like my video please Subscribe,Like,Share and Comment below what do you want me make in the next video.

[@erbenton07]

100ah is the same as 1 amp for 100 hours or 2 amps for 50 hours. ah = ampere hour. You dont rate chargers by ampere hours, you rate them by continuous amps output

[@WhiteGeared]

Wut? Are'nt you saying the same as him? Ampere hour vs. amp output sounds the same.

[@TheFandiahmad]

Can wr use this supply for spot welding ?

[@LongTechnical]

Not enough corrent bro

[@TheFandiahmad]

@@LongTechnical omg, ok i save more money for microwave transformer 😂

[@billywhizzy]

The problem with many good modern atx power supplies is that there is an over voltage protection which needs to be disabled too. Using this system will trigger the overvoltage protection circuit in these new power supplies.

[@muhammadasim3162]

kzbin.info/www/bejne/gH_Yf3WPlJp3rJo

[@Yangmist3r]

Hello. Please with resistor should I use to get 14.4v

[@عمارةحامدي-ذ7غ]

Hello, your video is great, I have already built the same charger as yours. I have another Power supply but its IC has a reference PJ494 CD. Is this type suitable for making a second charger with the same modifications? Thank you

[@LongTechnical]

All the same bro

[@DevavratPatil]

Bhai 165 ah ki inverter battery ko chrge kr skte hai kya

[@heyderaliyev8976]

your video really deserves a like (y)

[@omsingharjit]

Is its protection still working or not ( over voltage and current protection ) after modification of its Duty cycle dead time ????

[@LongTechnical]

Yes

[@omsingharjit]

@@LongTechnical how ?

[@harukoyama9515]

Can I ask u a question in regarding to measure AC and DC current. I am building a power supply from Microwave transformer. I have a Flute multi meter. It can only measure AC current. I can check AC current before and After the Transformer. But after circuit go through bridge rectifier. How can I check DC current ? Is there a way to mathematically convert AC current to DC current?

[@mehmetsuatbicer1324]

çok güzel bir icat :) hep bunu yapmak istemişimdir

[@atenglenon]

Sir, please correct me if I am wrong.. Isn't it means the battery will always adjust its ampere based on total load impedance? Even without that psu. I mean, if a lamp has 6watt burden and voltage input same as battery/12vdc, it will consume 0.5 Amp. If battery has potential energy of 100ah (as you said, but I'm not sure for that small battery), so it will last for 200hours. Pardon me since I don't know much about electrical stuff.

[@nickduning6170]

How do i up the amps to make a fan faster

[@LongTechnical]

Just incease the voltage output

[@infiniteman12]

hello, I have an atx power supply too. i was surprised that our power supply uses the same 2 ICs, when i put the 33k ohm resistor in pin 1 to pin 7 of AZ7500BP IC, i got 13.8V but it turns OFF immediately, how can i make it turned on always?

[@LongTechnical]

Try to use 39K resistor

[@SaifMusazai]

i have desktop computer powr suply having default output voltage 12v. I conect variable resistor 3296 with main i.c and voltgae increased upto 14.5v. Is it safe to charge my car battery?

[@LongTechnical]

Example your battery is 40Ah. Yhe good current charger about 4A. So you need use the current clamp or VOM for measure the current charge at with 14.5V input. If the current very high you need to down it by use the halogen light bulb like my video

yes car batteries can take 14.6 volts and pretty much any current if it doesnt overheat. so yes its safe

[@1981dasimpson]

yes thats safe current will limit as the battery voltage rises equal to that of the input voltage when fully charges current will be close to zero

[@SuperSayiyajin]

Can i charge my 100Ah 12V battery with this ?

[@elyzensshuffledancemix2095]

Where can I salvage from that 33 kilo ohm piece?

[@LongTechnical]

Ebay or utsource bro

[@wengieboy2011]

Good tutorial, your illustrations is a lot better than other same mod on KZbin. We can add a switch to the 33k ohm resistor to select between 12V and 13.4V output as we wish. Thumbs up!

[@LongTechnical]

Thanks you

[@muhammadasim3162]

kzbin.info/www/bejne/gH_Yf3WPlJp3rJo

[@rodniedelapena2513]

how many watts is the 33k ohms resistor used in this??

[@LongTechnical]

1/8 1/4 1/2 1Watt All OK

[@rodniedelapena2513]

@@LongTechnical thanks.,.

[@mckeinley1]

How do i know if the current is to strrong for charging a battery?

[@LongTechnical]

This is simple circuit, i will upgrade it to new version with current setting for any battery capacitor

[@humanitysolutions1811]

What amp will I get

[@edmardavecagatin4672]

Can this circuit be able to charge up the 200 Ah battery sir? Or do I need to change the resistor you have installed? Thank you! Have a good day.

[@LongTechnical]

Check my new video. Have new video for 200Ah battery with smps transformer

[@jeremydenn6988]

What does the light do why do you need it..

[@gus6rocks]

Brave boy, turn PSU off take out mainboard and handle terminals underneath with charged capacitors....Good one

[@LongTechnical]

Thanks

[@hansmuff3910]

Until now i have opened 3 PSU, but every was diffent from ur´s and had different Chips. What to do???

[@mohammadzare9927]

all of them are same

[@Robert.K]

How many amps is this able to deliver at 13.7 volts?

[@LongTechnical]

From 8A-10A

[@Alpha_Agro_Allied_Ind]

can we use it to charge 12v 35amp car battery?

[@LongTechnical]

yes

[@vladveron1619]

14.5 v normal, 13.5 small voltage for acid acc.

[@LongTechnical]

Yes. Thank you

[@1981dasimpson]

14.6 for one off charges 13.6 float charge cars charge to 14.6 volt current drops off the higher the voltage gets ion battery to supply power

[@Thetechnicalinfo20k]

Charging voltage is 14.5.and this method is applicable for all model of computer supplies !

[@victorrinz6856]

14;2 norml

[@samuelvillaver3479]

Do I need to add another load if I have a 100AH battery?

[@LongTechnical]

+c sammy ni oi you mean dummy load. With 100ah battery you don't need dummy load

[@TheKetsa]

Install a potentiometer instead of a 3.3kohm resistor? What voltages can we get min/max?

[@LongTechnical]

I don't know

[@CheapskateProjects]

Excellent! Would it be easy to also modify the 5V output to 6.5-7V in order to charge 6V batteries? Additionally adding a switch to bypass that light bulb would give a possibility to easily change between low and high current for different batteries.

[@LongTechnical]

+CheapskateProjects when change the 12V output to 13.5v ,the 5v output also change, i don"t measure but i think the voltage about 6.5v. At the next version i will adding a switch to bybass the light bulb. Thanks for you idie

[@fadereal1]

Hi.. nice video and tutorial..! I'm trying to make a car battery charger., can i use this method of your..? do the earth (GND) needs to be isolated like most of the videos i've watch.. the reason i ask is bcoz your method is the easiest way.. and i didn't see how you gnd it.. kindly please reply me.. i'm new to all this and i needed a 12 volt car batery charger. Tq in advance..

[@LongTechnical]

You can use my project for charging your car battery. But need to check the current charging

[@deemashakir5352]

good idea .

[@jaymalk5693]

Can you use it to power a car amplifier ???

[@AbhishekKr1902]

yes

[@rehanali-gb9uh]

Dear different IC method change I mean IC point and OHM change??????????????

[@LongTechnical]

no

[@sarulraj]

Excellent. It's woking as you say. Can you suggest how I can do the same for charging a 24V 100AH battery?

[@LongTechnical]

step 1: Make 12 battery charger from Computer PSU like this video. step 2: Check my channel i had video for make 24V from computer PSU kzbin.info/www/bejne/g6fcnmx3ptGVq7s Step 3: Use computer PSU on step1 for make like video at step 2 Step get 24V 100Ah battery charger

[@yassine9914]

@@LongTechnical ☺

[@pavlinvalkov6280]

My PSU uses weltrend wt7520. How much resistor must i put and which pin ?

[@LongTechnical]

i don't know this PSU

[@humanitysolutions1811]

How much amp will I get.cant I use 10/20k resistor

[@LongTechnical]

+Azizul Hakim yes

[@humanitysolutions1811]

How much amp will I get?

[@ginyodquinoa7756]

what is the use of the light bulb? im just curious. it didnt turn on

[@therealb888]

Gin Bulag If u don't understand u should learn the basics of electronics first. The little light bulb is for resistance aka a current limiter.

[@kaunisiapa]

And as an indicator when charging is full..!

[@pollydor07]

Only resistor 33 kilo ohm used ?

[@LongTechnical]

yes

[@LongTechnical]

+SANG THONG yes

[@pollydor07]

I checked on ebay for transistor 33 kilo ohm they have so many watts . which or how many watt should I order ? 33 K ohm plus how many watts ? thanks

[@LongTechnical]

1/8 W, 1/2W,1W......so ok

[@bionicblitz171]

the idea is good but dont expect a PSU like the one in the vid to put out 100A

[@therealb888]

BionicBlitz lol that PSU can't even do 50A on the 12V line. It does around 20-25A. All combined it does around 70A I guess.

[@LongTechnical]

100A battery charger not 100A ouput charger. With 100A battery the current charger about 10-20A

[@bangkong3495]

BionicBlitz: 10-20A it's more enough to charging 100A battery with 5-6 hours time

[@kaunisiapa]

He said 100Ah.. not 100A..!

[@SaifMusazai]

i want to charge my car bettery with computer power suply. But in power suply there is a yellow color wire having voltage is 12v thats ok,,, but ampere is low as about 1ampere to 2ampere only (which is not suffient to charge my car bettery). My problem is that how to increase the amperage of (yellow 12v wire) so that it charge my bettery easily. regds, thanks. plz reply in detail to solve my problem

[@LongTechnical]

It depends on your power supply

[@SaifMusazai]

Long Technical my p.sply atx 300w

[@LongTechnical]

You say me " but ampere is low as about 1A...."

[@SaifMusazai]

Yes my ampere show me only 1amp. And when you check the ampere on 12.7 volt, there also 0.34 amp aprox.

[@rahilshaikh3782]

How to get 15v from this atx

[@stephanreading5639]

is it possible to do this with lm339n comparitor

[@LongTechnical]

Check another IC on your board. it can have 494, 7500.

[@suryapatnaik5720]

For 2005z chip smps? Any mods?

[@LongTechnical]

I don't know that IC

[@ellooku]

No auto cut off?

[@LongTechnical]

the max voltage of charging machine is 13.5V. When the battery full the voltage about 13.5V. So the voltage of battery equal the voltage of charging machine. So no current charging and don't need cut off. If you want cut off, check on my video kzbin.info/www/bejne/hKbUo6eZd5aSgdE

[@therealb888]

Long Technical that's where u go wrong. Batteries aren't that simple in reality. I know u speak from class 12 physics but batteries can overcharge easily. This can cause damage to the internal electrodes inaddition to overheating which itself can lead to leakage, brittleness, etc etc.

[@reymondjosuearguellorojas2519]

Good músic at the start of the video spectre of alan walker greettings from Jicaral puntarenas costa excelent video only quality and like tenths in costa rica pura vida👌👌

[@jeremydenn6988]

How did you figure out that it's pin 1so on thanks

[@snufsof8300]

Thank bro. I have at 2500b chip my psu. Would this app be for my chip?

[@LongTechnical]

No i dont have

[@NguyenNam-tj7vk]

Ic sd6109 lam the nao bac

[@TheAtomstrike]

7:55 Goodbye 10A multimeter range!

[@LongTechnical]

+TheAtomstrike No problem man LOL

[@reinagam6423]

Osea tú Cargador no prende un foco de automóvil, solo está preparado para cargar una batería, bueno eso es lo que entendí, amigo debes de traducirlo a español porque ya no tendría que adivinar, bueno soy una persona que estoy aprendiendo y te agradecería para el bien de todos, Ati porque tendrías más comunicación con las personas y ahí me incluyo porque lo veo interesante tu vídeo pero no lo entiendo, no me queda más que adivinar o sacar aproximaciones de lo que quiero aprender, de todos modos gracias por compartir, un cordial saludo desde Perú, espero ver más vídeos tuyos con traducción gracias y bendiciones

[@cheezst8ke]

thicker wires for the output would be good to for using it as a charger.

[@jeremydenn6988]

The reason why I am asking is.. I want to do the same thing so can you please help me..

[@LongTechnical]

Decrease charging current to batterry

[@FLomasterZ]

You can solder variable resistor to pin 7 and to ground. And change V output to what you need without loss energy in lamp.

[@LongTechnical]

no. the battery can not full with your idea

[@sleteck8608]

Super

[@LongTechnical]

Thank

[@jomelyntrencio1365]

How to convert charger 48v.power supply CPU.

[@LongTechnical]

rewinding

[@SaifMusazai]

Which to rewind ?

[@jessieison4919]

can i charge 2sm battery car

[@LongTechnical]

yes. 12v battery

[@luistoribio6031]

110V 800W(todos los electrodomésticos en total consumen 800W)

[@markodewa7593]

my psu is raidmax rx-380k it usesc6105b nl4d0xd 10 pin how much resistor must i put and which pin ?

[@LongTechnical]

+marko dewa can not modify with this powersupply

[@markodewa7593]

Long Technical i just buy a dc dc adjustable converter , if i use -12 and +12 cable it will be 24v right , i will step it down with adjustable converter . it should work right ?

[@LongTechnical]

it working but the -12v on ATX with small Ampe you can check it at detail on the case of ATX power. If you want to more Ampe just do with instruction here: kzbin.info/www/bejne/g6fcnmx3ptGVq7s

[@markodewa7593]

Long Technical okay i will just step up the +12 to 14.2 volt with dc - dc step up converter . 14.2 is ok to charge my old motorcycle batterai right ?

[@LongTechnical]

yes. But need check current charging

[@jagannathfuji2493]

sorin diy make his lab bench power supply

[@alfredintelligence1594]

What happens if we use 20K or 47K resistor?

[@SaifMusazai]

In my atx there is only 1 ic 494, but in video there are two ic,s. Can i conect 33k resistr with my atx?

[@LongTechnical]

Yes

[@ravinderverma5013]

Music tusi hi sunya kro

[@testaja3614]

Please help If i want 13,8 and 14,2 volt What size of resistor i use?

[@LongTechnical]

use portentiometer 50K and adjust it

I think that the PSU have 300 and not 1200W.

[@luistoribio6031]

400AH(cargar la bateria de 12v con 400A durante 4 horas)

[@pollydor07]

THANKS

[@demebar]

Excelente !

[@victorrinz6856]

use résistance variable 47k to set voltage secondaire

[@RavinderKumar-h5f6c]

Yeh pta ni hunda ta video na bnaya kro music sunya kro tusi😅😅logo ko kyu sunate ho

[@pulzarmicrochip]

Modifica una fuente atx a 12 volt y 100 amperios en otro video

[@gokulg264]

sir my smps ic is 2003 and it is 18 pin .please help me to mod these smps

[@jessieison4919]

can i charge

[@LongTechnical]

yes

[@pollydor07]

Thanks

[@mnalam007]

Please give me just diagram please please please How to make 9 volt DC auto cutoff power supplier? Two row,one goes direct to device and another goes to from battery to device.(both lines 9 volt DC) When current is gone battery make sure to power supply. How I make it? Please answer me Give me a circuit diagram

[@lucianonocerino3670]

Va bene il resto, ma mettere subito le mani sulle piste dove hai appena staccato tensione è da fuori di testa! Vi sono condensatori con tensioni elevatissime!! Prima di mettere le mani, accertatevi che siano completamente scarichi. Vi ricordo, che in corrente continua oltre i 60 volt, è estremamente pericoloso venirne in contatto.

[@LongTechnical]

Thanks for explain

[@юрийгусев-щ9к]

what do you shove

[@harishtrivedi9959]

Gungi film dekhne mein maja nahin aaya

[@gokulg264]

sir my smps has only one ic and it is not tl494 or 7500 ic, it is 2003 baz78150415h please tell how to mod these smps

[@LongTechnical]

i don't know about your power sorry for that

[@DannyTillotson]

Good car or motorbike battery charger but no way 100Ah. You can buy a car battery charger for 6A on ebay for very cheap. No need for all this I don't think. Interesting though, thanks.

[@amitka1234]

The maximum output load of any ATX is 400 watt whereas your load is 12 volt x 100 amp = 1200 watt. So how will the ATX bear the load ? It will charge 7 Amp battery only which you have used.

[@luistoribio6031]

tu habla mudo(perdonarme si no veo tu rostro)

[@malikzai9607]

Swg war gauge kapar Wala Swg war gauge kapar

[@BryanChance]

Oh that fucking music...

[@Coofy4]

Why must be there this kinda annoying music in every second DIY video?

[@kamildrozdzyk6061]

13.5V ? what is wrong with you... AGM charge is best 14.9v, GEL, 14,6 . STD- upper 16.3v

[@LongTechnical]

Safety around 13.5 to 13.7 for all battery

[@kamildrozdzyk6061]

@@LongTechnical Not for charging.... 13.8V is recommended for buffor after full charge stage. 13.7 and charge to the full any Ca/ca? impossible

[@LongTechnical]

I don't know. With me 13.7 V is enough for my battery. I think it safety. You can increase to 14.4 V or more

[@-Crash-Nebula--]

why?? the batteries are charged with 12 volts how old are you? 10

[@thanhlong-suaientu3319]

You are stupid man. LOL

[@PAWELEKTRONIK]

hello, I have a power supply atx integrated circuit S494P how to do reworked 12v to 14v voltage? photo links chomikuj.pl/pawelektronik/PHOTO