How To Make a Ruler Marking Gauge / 그무게 마킹게이지 만들기

[@jinhokim2239]

판매하신다면 구입할 의사 있습니다. 그무개 만드는 영상 중 최고입니다. 감사합니다 ~~

[@letsdiy9521]

아쉽게도 판매 계획은 없네요 영상에 관심가져 주셔서 감사합니다 ㅎㅎ

[@GinoGenero]

It's beautiful but I would skip the steel dowels or use hardwood or plastic dowels. Also, adding a protective plate of some kind where the thumbscrew contacts the ruler would save eventual wearing away of the printed scale. 👍

[@vanislescotty]

This is a great little project. I enjoyed this. I'm thinking a very small notch in the end of the ruler will help guide the pencil and make it a little more accurate when marking. But I did love this.

[@letsdiy9521]

thank you for your valuable comment

[@antoniogarcialopez9849]

@@letsdiy9521 lo

[@김용륜]

명품을 만들기 위한 또 다른 도구 만들기입니다. 대단히 훌륭하십니다.

[@letsdiy9521]

좋은 말씀 감사합니다 ㅎ

[@aaartisans6467]

You work very neatly and concentrate completely on the product.

[@neliorodrigues2249]

Muito bacana ficou joinha seu gabarito para centralização de furos e outras transferências de medidas é muito boa à apresentação só faltou as MEDIDAS mas muito obrigado VALEU mesmo de verdade ficou show

[@letsdiy9521]

Thank you for watching the video with interest

[@MrJcasilva]

show de bola! a ideia da tupia foi sensacional para o rebaixamento do encaixe da régua!

[@fabiobasscam]

A lot of learning in a single video! And great job done! Thank you for sharing!!

[@letsdiy9521]

Thank you very much for your interest in the video

[@Sedge63]

I am very surprised that you still have all of your fingers.

[@jaimealcantara5057]

Excelente trabajo y muy bonito, una consulta, que liquido le pone una vez terminado ?. Gracias

[@letsdiy9521]

Instant adhesive was applied to the piece, and wood oil was applied to the exterior finishing material thank you for watching my video.

[@creativetdt23]

Guys, I am really surprised and love it.

[@cesarb3484]

Muy útil y practica herramienta, me encanta, y espectacular trabajo. Me podrías indicar qué tipo de madera usas ?????? Gracias

[@letsdiy9521]

It is a tree called IPE.Thank you for your interest in my video!

[@williwichtig3028]

Basically a good project. Especially the choice of wood is mega! What bothers me is the position of the locking screw. This will destroy the engraving on the ruler after a short time. I placed the screw on the side and clamped the ruler with it.

[@letsdiy9521]

Yes, but Even if you tighten the screw weakly Is fixed enough The number is not erased Thank you for your interest in my video!

[@j-book3937]

I agree with the concern. Perhaps a nylon screw or small, short piece of plastic rod under the screw. Another solution I have seen is to add a brass shim plate between the screw and ruler. It is a nice project.

[@richardM980]

Nicely done. Thanks for sharing!

[@letsdiy9521]

Thank you very much for your interest in the video

[@Painless61]

Very nice build ... By the way ... i finished my crosscut sledge like you build some time ago 👍🏽 it works perfect♥️

[@letsdiy9521]

Very good news! Congratulations on your success in making sleds!!

[@НиколайСтепанов-з1в]

Практично и красиво. Спасибо за идею.👍👍👍❤️

[@letsdiy9521]

Thank you for your interest in my video 👍👍👍❤️

[@peterharman8466]

Nice job n great finish 👏👏 to be honest I was expecting to see blood and parts of fingers being lost. Clearly a master craftsman with absolutely no fear of moving blades so close to fingers not for me though safety first aesthetics later 👏👏👏👏👏👏

[@letsdiy9521]

From now on, I will upload a video of working while observing the safety rules.

[@peterharman8466]

@@letsdiy9521 hi please don't misunderstand me I was not criticising your work or working methods I really enjoy watching you work, clearly you're comfortable with your capabilities and I totally, absolutely respect that and I offer my sincere apologies if I offended you it was not my intention

[@latanadeglihobby]

Very good great video and job

[@letsdiy9521]

Thank you very much for your interest in the video

[@illergiuliotti1896]

Perfection is like that! Not necessary others comments!

[@letsdiy9521]

Thank you for your interest in my video

[@TheMrWoodsman]

Table saw safety at its best, well done. Peace

[@Mukes4889]

Lots of love from Nepal.

[@PremKumar-qf8te]

India.tamilNadu 📝👌😃🙏 super sir

[@emersonhotrod]

Beautiful!👍🏻👍🏻👍🏻

[@letsdiy9521]

Thank you for your interest in my video

[@rkalle66]

I don't like the direct contact between clamping screw and ruler. This will leave scratches and may move the ruler while rotating the screw.

[@Tensquaremetreworkshop]

Agree. There should be a clamping strip. Also, the sides of the rule need metallic support- wear will mean it soon departs from square. And the steel dowels are redundant- just fake rivets. Lots of time spent on the wrong areas.

[@georgezosanglienjoute8568]

can you please tell me the size of wood which you are joint

[@letsdiy9521]

The tree size is 80mmx35mmx16T.Thank you for your interest in my video

[@澳洲生活]

Nice work!

[@letsdiy9521]

Thank you for your interest in my video!

[@ИгорьСавков-ы7щ]

Пластинку подложить надо под гайку, что бы линейку не царапать. А так молодца!

[@letsdiy9521]

Thank you for your interest in my video

[@jonathanbobohunt6507]

why make that when a combination square does the same thing?

[@keupondestroy911]

Merci beaucoup pour la vidéo

[@letsdiy9521]

Thank you for watching the video with interest

[@lucasmnguni8475]

excellent job

[@letsdiy9521]

Thank you very much for your interest in the video

[@bcwalker1]

I can't believe how close his fingers are to the router bit!😵

[@migueldesantiago7258]

... or to the jig saw blade

[@SijeiGaming]

How about small C-clamp and a metal ruler?

[@letsdiy9521]

Sorry we can't translate the content of the question

[@AntonioAnt-ct6fn]

Ciao e grazie per il video. Puoi dire quale è la colla che metti per i perni/spine di ferro ?

[@김만길-b4q]

marking gauge 영상 중에 가장 마음에 드는 영상입니다. 좋은 영상 감사합니다. 마지막에 바르는 무슨 칠? 어떤것 인가요?

[@letsdiy9521]

영상이 도움이 되신 것 같아 뿌듯하네요. 마감은 목재용 전용 오일입니다 시청해 주셔서 감사합니다 ㅎ

[@김만길-b4q]

@@letsdiy9521 답글 감사합니다. 영상 건투를 빌겠습니다.

[@Astilafauzymeubel]

Amazing 👌👍❤

[@huguettebenigouet7055]

What is this nnice wood essence?

[@letsdiy9521]

Hello, this is a tree called IPE.

[@alexdrf1112]

Excellent!

[@letsdiy9521]

Thank you for your interest in my video

[@jlee9078]

안녕하세요~ 잘보았습니다~ 그 철심과 볼트는 뭐라고 검색해야 나오나요?

[@letsdiy9521]

안녕하세요 답변이 많이 늦었네요 ㅜ 문의하신 철심은 버려진 프린터에서 축출한 샤프트를 재활용했으며 노브 스텝 너트 또는 엄지 너트는 알리에서 직구 했습니다 ko.aliexpress.com/item/1005002663213250.html?spm=a2g0o.detail.1000014.23.3d522d6bv82Zn0&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.33416.213724.0&scm_id=1007.33416.213724.0&scm-url=1007.33416.213724.0&pvid=bb1f756c-73ba-4004-a6ec-333367dd9c66&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.33416.213724.0,pvid:bb1f756c-73ba-4004-a6ec-333367dd9c66,tpp_buckets:668%232846%238115%232000&&pdp_ext_f=%7B%22sceneId%22:%2223416%22,%22sku_id%22:%2212000021608548946%22%7D

[@АлександрОрлов-ф7з]

Отличная работа. Скажите, какое дерево Вы использовали, очень красивая фактура?

[@letsdiy9521]

Hello, this is a tree called IPE.

[@АлександрОрлов-ф7з]

@@letsdiy9521 Спасибо за ответ. Только я так и не понял. Что это IPE (сложности перевода).

[@АлександрОрлов-ф7з]

Нашел, это бразильский орех. Спасибо, доброго здоровья.

[@andrerevez4970]

Друг, не забывай о технике безопасности! 친구야, 안전을 잊지마!

[@bitsurfer0101]

Tree Species is called IPE. It is a very hard wood with a high specific gravity and will sink right away when placed in water.

[@bayu6695]

Gravity? You mean density?

[@paulcutty8048]

I was very confused, because I use the (apparently) exact same wood, and here in Switzerland it has the commercial name of Bangkirai. I am 99 % certain that it is the same wood, as it also sinks in water which is quite uncommon. And the close up show exactly the same aspect and structure of the grain. Also, same use: planks to cover terraces. So I went on the web site of the shop where I purchased it, to check. There is an official declaration of the wood. It reads: Origin: South east Asia., name of the species : Shorea laevis (= S. laevifolia). Ipe seems to be a totally different species, from South america (Handroanthus). So I am still confused , just on a higher level ;-) Any thoughts ? By the way, I like very much the constructions here, so neat. I would replace the screw with a brass one, to avoid scratching the ruler.

[@letsdiy9521]

Hello sorry for the late reply Unfortunately, I don't know the exact type of tree either. I received the remaining wood from an acquaintance after the interior work and used it. called Ipe And there are many ways to keep the ruler from scratching. I use it by processing the end of the piece into a round shape. Doesn't scratch the ruler at all thanks for watching my video

[@DmitryRun]

если уж выбрали базу, и от неё все расчеты, то зачем перетачивать её ещё ЧЕТЫРЕ раза на протяжении всего ролика??? и кстати, а как вы клей потом из ложе линейки удаляли? (7-50)

[@이재호-l5l]

대단하십니다!!!

[@letsdiy9521]

영상에 관심가져 주셔서 감사합니다 ㅎㅎ

[@youtukang]

🌹🌹🌹🌹👍

[@Zaizen0801]

그냥 신와꺼 만원짜리 쓰는게 훨씬 정확하고 좋아보이네... 이미 드릴할때부터 흔들렸음

[@JuanCarlosHM]

Please, subtitles in spanish. Thanks!

[@letsdiy9521]

This is a video without subtitles Thank you for your interest in my video

[@herbi102]

This one made it complicated that there is nowhere else to go

[@zackkardakos1979]

bravo!!!!

[@molambo]

Incredible! He makes a simple thing complicated with a bunch of crazy inventions! It removes the burr from the wood 1 million times, with almost no wood left, with a lot of expensive tools to make a measly gauge! That was never carpentry! It's almost discouraging!😡😡 Learn from the good old man: www.youtube.com/@GrandpaAmu/videos

[@agagagoghi]

I honestly don't understand why to put the two metal pins

[@laurentw650]

To secure the glued assembly maybe ?

[@dlk4318]

great work!

[@barrydoxseyuk]

Watch those fingers! If the wood. Snatches!

[@diybeginner3813]

Great job but never wear long sleeves if you work at a table saw

[@genekatauskas6904]

Nice

[@ahmeddaghriri4180]

Hi. Can i buy one from you ?

[@letsdiy9521]

unfortunately not for sale hank you for watching my video.

[@Klingonbr]

Muito bom, porém acho que o parafuso tende a danificar a inscrição da régua. Talvez fosse bom instalar uma chapa de material plástico entre o parafuso e a régua.

[@letsdiy9521]

There are many ways to prevent scratches on your ruler. It is used by rounding the end of the screw. Doesn't scratch the ruler at all. thanks for watching my video

[@Mekanikhobi]

Merhaba , dijital metreyi arıyorum . Nereden bulabilirim?

[@letsdiy9521]

I bought it from an online store.

[@daeeuljeoung1928]

나사에 끼우는 동그란 것 이름은 무엇이고 어디서 구매 하는지요?? 영상 멋집니다. ~~~!!!

[@letsdiy9521]

노브 스텝 너트 또는 엄지 너트라고 합니다 알리에서 직구 했습니다 ko.aliexpress.com/item/1005002663213250.html?spm=a2g0o.detail.1000014.23.3d522d6bv82Zn0&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.33416.213724.0&scm_id=1007.33416.213724.0&scm-url=1007.33416.213724.0&pvid=bb1f756c-73ba-4004-a6ec-333367dd9c66&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.33416.213724.0,pvid:bb1f756c-73ba-4004-a6ec-333367dd9c66,tpp_buckets:668%232846%238115%232000&&pdp_ext_f=%7B%22sceneId%22:%2223416%22,%22sku_id%22:%2212000021608548946%22%7D

[@rogerio160771]

👏🏽 👏🏽 👏🏽 👏🏽 👏🏽 👏🏽 👏🏽

[@martyjosephson4937]

Nice video, but you ahould NOT be wearing long sleeve 's at the table saw!

[@letsdiy9521]

Yes, that's right Thank you for your attention

[@antoniorosas1269]

어떤 종류의 목재를 사용합니까?

[@letsdiy9521]

It is a heavy tree called IPE. Thank you very much for your interest in the vid

[@kiwee_]

12:06 Most dangerous tool I've ever seen. Having a belt sander, what's the point?

[@powkinyap5328]

👏👏👏👍👍👍

[@sangbonghan5354]

영상 처리가 너무 훌륭하시고 잡스러운 설명 없이도 너무 깔끔하게 공정을 볼수 있어 좋습니다... 다만, 작업중 위험해 보이는 부분이 좀 있어요 맨손으로 작은 피스를 갈아 내거나 마름질 하는것과 본딩및 표면처리할 때도 직접 맨손으로 하시는데... 많은 사람이 보는 영상이니만큼 안전에도 만전을 기하는 작자의 의도가 깃들면 정말 금상첨화 일듯 합니다 --- 팬으로 부터

[@letsdiy9521]

네 안전은 아무리 강조해도 지나치지 않죠 항상 숙지는 하고 있는데 잘 안 지켜집니다. 더디기도 하고 말씀처럼 공개된 영상이니 보다 신중히 작업을 해야겠네요 좋은 말씀도 감사합니다. ㅎ

[@raynierllewis2827]

Why don't use a hand router .very dangerous

[@dreletronica]

Muita enrolação 😅

[@marcospimentel603]

Mejor compro la herramienta ya hecha!!!

[@edodibujos]

No se trata de eso. Para un carpintero es una gran satisfacción hacerse sus herramientas (las que se pueden hacer) sobre todo a la medida de sus necesidades. Además algunas pueden llegar a costar mucho y en algunos mercados locales pueden ser difíciles de conseguir.

[@tourvillecharles551]

👍👏👏👏👏👏👏👏👍

[@youtukang]

🤝🤝🇮🇩🇮🇩👍👍👍👍

[@thanhnguyenngoc6638]

Tay áo nguy hiểm quá bạn ơi

[@serggutych1264]

😊

[@MaxMuelller]

Es ist sicherlich hochwertig, was der Mann dort macht. Allerdings braucht man wahrscheinlich die Asiatische Ruhe, um sich hier jedes Detail anzusehen.

[@CarlosAlbertoPereiradeQu-bp7ds]

espetacular

[@whitewhale1162]

👍👍👍🙏

[@Riverman270]

Стальной болт будет жрать линейку

[@عاوزافهمليهكدا]

❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

[@mh2acustica]

👏👏👏 🇧🇷

[@Aaa-c1b7u]

Куча бессмысленной возни ради картинки, без полезного результата.

[@superzubu]

다치지않으셔야합니다

[@AntonioAnt-ct6fn]

Ciao. Iscrizione e like fatti. Minuto 5.57 inserimento boccola filettata. Per favore puoi dirmi la misura del diametro del foro e la misura del diametro della boccola filettata. Io ci ho provato con boccola diametro 10mm e diametro foro 9mm. La boccola non riesco ad inserirla perpendicolarmente, entra inclinata e rompe anche il legno. Ti sarei davvero grato se mi rispondessi. Antonio

[@Jakob47recordermaker]

Foro e boccola devono avere lo stesso diametro, per es. 8 mm. a mio parere lavora molto meglio JSK-koubou. Cerca "Calibro di marcatura del righello"

[@큰느티-f2j]

👍🏻👍🏻👍🏻👍🏻👍🏻🤝🤝🤝🤝🤝🤝🤗🤗🤗🤗🤗🤗🍺🍺🍺🍺🍺

[@brandonmeade8999]

Anyone noticed the blood at 12.11

[@ahmeddaghriri4180]

あなたから購入できますか？

[@letsdiy9521]

unfortunately not for sale hank you for watching my video.

[@renzodalsanto7408]

Solo manierismo

[@배범진-m4e]

만들어 판매하셔도 될 듯

[@letsdiy9521]

최저시급도 안 나와요 영상에 관심가져 주셔서 감사합니다 ㅎ

[@lalitkhinchi5779]

Though the product is super fine.... there is Too much detailing and not very safe way of working at all...... not even gloves

[@2sansamify]

다수의 사람들이 엄지척 이지만 저는 아닙니다 아무리 목재가 좋아도 같은결로 제작하는곳은 잘못.미스 라고 봅니다 한쪽편 나무는 길이 결로했어야 됩니다

[@2olmeca]

прямого угла у этого самоделкина при такой технологии фрезировки точно не вышло, а на 12.01 у него вообще кровью лобзик заляпан, бгг

[@ALEX_UNIVERSUM]

Среди корейцев тоже есть рукожопы.

[@토르-n9c]

음 뭔가가..... 같은공정을 여러번 반복하는 느낌 마지막 한번에 다해도 될듯싶어요 ~~^^

[@letsdiy9521]

영상 관심 가져주샤서 감사합니다 ㅎ

[@adrianquintero01]

Que desperdicio de juguetes.

[@luissouza5501]

Show !!!!!!!!!!

[@CarlosAlbertoPereiradeQu-bp7ds]

🎉

[@神保孝幸]

斜めに打てるボルトの治具作り方

[@dutrstango]

Dude. Is not ipe

[@youtukang]

Hyyy 👍👍

[@갈매기부산-t9v]

대체 이런영상에 왜 굳이 음악을 넣는지 도통~ 배경음악 넣으면 멋있게 보이나?

[@heaven4261]

귀 처 막고 처보면 됨

[@double956]

超危險動作