Рет қаралды 121,304
Making Double flared brake pipe - 16 Tips! (and stages)
1. Practice on spare pipe first.
2. Use plumbers pipe cutter to cut brake pipe.
3. Measure the length needed using some plastic pipe that easily bends around the route required.
4. Flatten the pipe end with a file. Clamp pipe in the flaring tool.
5. Remove burr from inside pipe & add a light chamfer to inside using a knife.
6. Chamfer the outside end with a file.
7. Don't forget to fit your pipe fittings now IF this is the last end joint!
8. Use a quality flaring tool.
9. Clamp tool in vice.
10. Set the pipe in the tool protruding with the pipe height to first edge on die
11. Lubricant with brake fluid on pipe and die, top and bottom.
12. Set top of tool twisted, so up against bottom part, so fixed at 90 degrees vertically. Check alignment!
13. After squashing down with die until die touches tool, remove and check pipe end is symmetric and has a squashed bubble end, if not start again!
14. Remove die carefully by turning and wiggling (easy to break the die end off here if too harsh) and squash pipe down a bit more with just the cone of the top tool to lightly increase the flare and double over the end a bit more.
15. Don't over do this last stage, better to do a couple of light squashes and check inbetween than do it too squashed and weakened.
16. Use a pipe blender tool on tight pipe bends.
Here is where to buy the tools required:
Draper pipe flaring tool: amzn.to/2bxd2zk. (Amazon USA)
amzn.to/2c8B0Fn (Amazon UK)
Copper brake pipe and joints:
amzn.to/2bLpApQ (Amazon USA)
amzn.to/2bQvB48 (Amazon UK)
Pipe cutter:
amzn.to/2bLMA5q (Amazon USA)
amzn.to/2bQwv0n (Amazon UK)
Pipe bender:
amzn.to/2bxn1Ez (Amazon USA)
amzn.to/2bQwOsb (Amazon UK)
Or if you prefer EBay for the tools and stuff just search on there, here's the draper flaring tool to start off on eBay USA:
rover.ebay.com/...
Or eBay UK:
rover.ebay.com/...
Rubber disposible gloves are also useful, here's the links for
eBay USA: ebay.us/GGqmTJ
eBay UK: ebay.us/cE1BHK
Amazon UK: amzn.to/3aikbl8
Amazon USA: amzn.to/3cdwjpD
Amazon Canada: amzn.to/2Q0VHZm
Amazon Australia: amzn.to/2QlUawX
Note that there is a small difference between imperial and metric brake fittings, the male fitting nut is slightly smaller on imperial so buy accordingly. Most cars from the last 20 years at least should be metric I believe.
If anyone wants to show appreciation for any money savings, or just help support the channel and future videos then you now can. Use this link: paypal.me/comei...
OR you can support me by using the above Amazon and Ebay links to buy other stuff that you would usually buy, it will not cost you anything more, but will help this channel.
Subscribe to the channel for similar DIY, fixing stuff, car bits and tech reviews here:
www.youtube.com...
Note, if you want to be notified of new videos click on the bell symbol on my home page.
The video is about my personal opinion and experience and contains no paid for product placements. No responsibility is accepted for any perceived recommendation for or against a product or feature nor any consequential damage or harm since this video is just my personal experience. You accept by watching this video that you accept any responsibility for any subsequent actions or decisions that you take. Please be aware of what type of material (copper, copper/nickel or steel) is allowed to be used for brake pipes in your country and buy accordingly.
Note on copyright / licensing: This video was created using Apple iMovie and as such any music or video content is fully licensed by their terms and conditions for free publication and distribution.
See the Apple iMovie software license agreement at:
images.apple.co...
Which states"all Sample Content included in the Apple Software may be used on a royalty-free basis in your own video projects"