How to Pancake a C10 Crossmember

[@awrosemba]

Seriously impressive fabrication you got going on there. Also, another seriously cool car keeps showing up in the background!

[@TheOddRodGarage]

The Camaro is coming up! Thanks for watching!

[@williamwright6157]

That was pretty cool. It makes us appreciate custom work.

[@TheOddRodGarage]

It's a pain but it's worth it! Thanks for watching!

[@kimberlywilliams9757]

Tommy is really putting some elbow grease into that! That's a great job on that, very impressive! Keep up the great work and thanks for sharing! 😊👍

[@TheOddRodGarage]

Thanks for watching!

[@kennethsonier1766]

You guys did a fantastic job. That chassis looks cool as hell also. Keep up the great work and the excellent videos 👍✌️🇺🇲

[@TheOddRodGarage]

Thanks for watching!

[@bobjarman176]

Fantastic job on that pancake. I’m with you on that tape problem. Layout was much easier when you didn’t have to deal with a decimal. Leave the tape width alone!

[@DegenerateFabricators]

Thank you so much for this awesome video!

[@rebeccaryan6229]

Nice work!

[@TheOddRodGarage]

Thanks for watching!

[@seanjhonson6441]

3:22 hell yeah brother! 😂

[@pawpatina]

what about the steering linkage alignment now? flip the tie rod ends to the bottom of the spindle?

[@willfarrell3332]

It laid frame with 1 3/4” removed ? Good work looks clean !

[@TheOddRodGarage]

Check out this coming Sundays video.

[@willfarrell3332]

@@TheOddRodGarage that’s to long to wait !!!! Just tell me haha !

[@michaelforemansr6571]

Bolt holes on side of frame won't line up.

[@rmoct]

I had the same question what do you do with the side bolt holes from the frame to the crossmember the bottom lines up fine

[@PeterHatch-mx7zc]

Thks for the video i hace c20 front clip was going to craft the clip in now i see this pancake have 1953 ford van 132 wb dont know witch way to go any advice thks

[@TheOddRodGarage]

I've narrowed crossmembers before and put them in older vehicles. I'd go C10 not C20. They are different. C10 has more options.

[@PeterHatch-mx7zc]

@@TheOddRodGarage why c20 the diff is c20 full floater and Detroit steel make rims for 8 lug

[@PeterHatch-mx7zc]

@TheOddRodGarage have a 468 blown t400 I'm going to set the engine back the WB 132in

[@JAYSVENTURES]

Why not only cut a section off where the frame can slide in?

[@TheOddRodGarage]

Thinning the frame weakens the frame. Most of the weight of the car is up front. Thanks for watching!

[@couchninja2997]

did this change you camber at all?

[@TheOddRodGarage]

No. Thanks for watching!

[@kirbystafford6901]

Hey guys, It looks like the steering rod will touch the harmonic balancer on the SB??, also looks like the pancaked cross member doesn't have room for the oil pan?? comments??, suggestions? THANKS

[@TheOddRodGarage]

There is plenty of room between the pan and the crossmember. There is also no problem with the harmonic ballancer. I'll try to get better pics

[@TheOddRodGarage]

Balancer

[@skipwaelty3974]

First time I've seen your channel. As soon as you ask the commies and socialist to unsubscribe I subscribed. Priceless!

[@michaelforemansr6571]

Butchery just buy drop spindles an do it right.

[@TheOddRodGarage]

You can't lay the frame on the ground if you just do spindles! Study a little more and you'll figure it out.

[@couchninja2997]

worthless mod!~

[@TheOddRodGarage]

To lay the frame on the ground you must do this or purchase a different crossmember. Thanks for watching.

[@couchninja2997]

@@TheOddRodGarage no? you just deep cup lower lower control arm!

[@couchninja2997]

@@TheOddRodGarage ​ @ccgarage5040 you can deep cup lower control arm or Z cut frame