How to Program Chamberlain KLIK2U wireless Universal Keypad

[@joannemierzejewski6919]

Thank you so much!!!! Key for us was to do the process slowly. You don’t need to rush through the process. We were trying to speed through the process and therefore the learn button was still on. We have an orange button so we were 2#. This was the most helpful video!!!!

[@robbarron3356]

Best set of instructions. I watched another and did it 10 times and it didn’t work. I assumed the sender unit was bad. Stumbled upon your video and BAM! worked like a champ. Much thanks!

[@HomeRepairHub]

Glad it helped

[@robertgraziano8326]

Thanks for simple walk through and especially for mention of ‘double zero’ input for Genie. I watched a different video that missed that detail and it gave me fits watching and rewatching that video, wondering why it didn’t work. Then I found your video that included that important detail. Thank you.

[@be_early2024]

Older home maintained because of great detailed videos like this one. Thank you!

[@shanewyer5226]

Thanks! The instructions show that it needs to have a two-digit ID. After watching your video and seeing only one digit is needed, the programming went well.

[@dwightphilipoom6734]

Best one yet out there because you showed the instruction sheet with the list of the color button and associated code number which was the yellow button and the number 8 for my lift master. Thank you

[@phillyskillz1428]

This one goes down as an oldie but goodie!! Helped me out alot thanks bud

[@grantknight3978]

So much easier to watch than the Chamberlain video. Thanks!

[@robertjacques7064]

OK the directions that are supplied or not real clear on certain things and I was already frustrated but the video explain everything perfectly. Thank you.

[@Robertpeace233]

Been trying to figure out why I couldn’t program a new keypad till you mentioned I had to hold the # and * at the same time till they STOP flashing god I wish I knew that sooner! Thanks!

[@annerich3268]

This was the best instructional video ever! Thank you

[@Kovi2000]

Awsome instruction, it helped me to program my old remote control works like the new one, thank you!

[@davidw.mcclain257]

Just what I needed and thanks for showing the page with the door type codes! Worked great thanks.

[@CB-gi6yr]

Quick and easy walk thru, worked perfectly. Thanks!

[@richardschulz8191]

Great instructions. Fixed my issue with my Craftsman 1/2 HP opener.

[@HomeRepairHub]

I appreciate the feedback

[@BarristerBrian]

Finally a video that worked! Thanks!!!!

[@regiaguilarjr9390]

thank, mine is a chamberlain LiftMaster with a purple button, and the 3 is code worked for mine. thank you for your video worked great

[@josuecarias2914]

THANK YOU VERY MUCH FOR THE INFORMATION. IT IS CLEAR AS THE SUN LIGHT. HAVE A GREAT DAY.

[@adamnath7787]

How do you program two garage doors with this keypad? Both doors have sears craftsman openers with green buttons. Thank you for your help.

[@HomeRepairHub]

I believe it's just the same process using the other opener. Just set a different code

[@adamnath7787]

Appreciate your time. @@HomeRepairHub

[@norrisborden]

Life saver. Thx for the video. 2 thumbs up.

[@justinwhite3257]

Great video! Short and right to it!!!

[@HomeRepairHub]

I appreciate the feedback

[@johnerodz7]

This is the best video ever thanks buddy ❤

[@reneeklenner1176]

Can you tell me how to get the cover off??? I opened the box and I am stuck on getting the cover off the key pad.

[@jamiebonczek8026]

I just used grip and force to lift it up.

[@Stacie2440]

Do you enter the code on key pad while the light on motor is on for 30 seconds or do you wait until light on garage door motor goes off then enter code on keypad?

[@HomeRepairHub]

You just need to wait for the light on the keypad to go out.

[@Stacie2440]

@@HomeRepairHub And it’s fixed! Thank you!!!

[@joekarnsenko]

What if my old 2001 ChalengerGL opener has no "learn button"? There is an original keypad I'm trying to reprogram since I just bought the house.

[@HomeRepairHub]

Not sure. You may have to buy a challenger wireless keypad. Does it have dip switches? I believe Wayne Dalton owns them now.

[@jameshaskell1073]

I did this a few months ago when I bought the unit. ####0 worked to open and close the garage door, every time. Great! All of a sudden today, ####0 opens the door. But it doesn’t close it. Now it’s ####0 plus any other key to close it. What’s up with that!?!?

[@tgoodfella]

Thx directions helped

[@jerrydavis9581]

How do you sync the clicker and the keypad?

[@HomeRepairHub]

What kind of opener do you have? The clicker, sync with the opener same as the keypad. Here is example, its a Genie opener, but it will be similar. They all program pretty similar, just the number of times you hit the button will change. kzbin.info/www/bejne/Y6iWpmecmbpjY7M

[@lykastannis7662]

When I hold the two buttons down together, they simply light up without flashing. Any tips?

[@HomeRepairHub]

Do you get any lights when you hit the buttons? May want to just put fresh batteries in if you haven't used it in a while.

[@lykastannis7662]

@@HomeRepairHub Yes every button's light flashes, but it just stays lit up rather than blinking until I release. I only noticed this after a 2 month vacation so I havent used it in a while. I'll try switching batteries. Thanks!

[@rickgallegos6530]

Same. Need hard Reset. What’s the button inside battery compartment?

[@rickgallegos6530]

When pressing both buttons, it only lights up, no blinking.

[@unchboy]

Is that cover suppose to be permanent and have to be broken to access the keypad?

[@rickgallegos6530]

No. Slides up and down to access keypad, while also concealing mounting screw at the same time

[@Courtney-bc2mt]

Thank you I was missing the part about letting your garage close all the way. Purple button code: 3 After you press the learn button then enter your code again. LET THE GARAGE CLOSE ALL THE WAY. Then enter your code and it will work. My issue was i didnt let it close all the way. So the code wasn't programming. Let the garage close before you hit another button.

[@henrygonzalez1201]

What a pain in the butt to program the device, but I got it done and , Thank you.

[@adambleazard423]

Good walk through

[@dani999777]

What if I have 2 garage doors?

[@HomeRepairHub]

Unfortunately the Klik2U can only be programmed to 1 door, so you would need a second keypad.

[@ricardoquezada6777]

Muchas gracias por la ayuda 👍👌

[@reginaldjackson5686]

Thank you this was very helpful and save me $150.00

[@Gary55379]

It needs the code to close?

[@HomeRepairHub]

Unfortunately, yes. Pretty much any aftermarket universal remote requires the code.

[@Gary55379]

@@HomeRepairHub The one I have now does not. I was gonna replace it because the buttons don’t always work anymore but if I need to enter the code to close it, we’ll, that’s just dumb.

[@vlockhart4835]

My Chamberlain garage door opener doesn't have any buttons on it now what

[@HomeRepairHub]

Are you talking about the garage door remote or the keypad?

[@summermoon4620]

If you have overheard motor press 0 twice on the end of your code when setting up

[@MegaDog2012]

Thank you sir

[@MichaelSondereggermusic]

Thank you!!

[@frankp9909]

Thanks!

[@Killyso]

Anybody know how to get the cover off lol

[@HomeRepairHub]

Unfortunately, there is no easy way. I had the same issue. You just have to use a bit of force when trying to slide it off.

[@Killyso]

@@HomeRepairHub been trying for a few days now and still can’t get the right grip to be able to force it. Pretty inconvenient design

[@bkehlin]

This does NOT work with LiftMaster

[@HomeRepairHub]

It should. What type of liftmaster do you have?

[@lesliemcgowan4306]

@@HomeRepairHub Ours worked just fine with our 2004 Liftmaster for 20 years.

[@matt75hooper]

This will program your keypad. But it then deprograms your remote controls !

[@nuubxiii5278]

My garbage ass product won’t even slide open. It’s honestly very annoying. Nobody, no matter the video seems to have a stuck clicker. You started your video off with an open one. Clearly it’s not suppose to be hard to open. It’s like they sent me mine glued…

[@HomeRepairHub]

I can be a bit challenging to open but shouldn't be that difficult. You can't pinch in on the sides or it won't open. The cover simple has to slide off and if you put any pressure on the sides of the cover it won't move.

[@nuubxiii5278]

@@HomeRepairHub Turns out they sent me a faulty product lol. I had to pry it open with a knife then I had to sand paper the grooves to allow the casing to open and close smoothly. So I got it done haha but it was for sure faulty! Thanks for the reply my guy!

[@keliciamitchell6068]

Just bought this and we can’t get it open as well! Oh well! It seems to be stuck

[@fluidgrace]

i had the same problem, i had to use three knives to get it unstuck and open it. I took an exacto knife and shaved some material off the inside cover and used a bar of soap to help it slide

[@vigrue-kingofscrew4804]

hi，we want to send you some products that fit your channel, do you have an email?

[@basilalsilawi3753]

So much easier to watch than the Chamberlain video. Thanks!

[@HomeRepairHub]

Thanks. I appreciate the feedback.

[@chaseman]

Thanks!