How To Properly Adjust A Chamberlain Garage Door Opener Including Tips On Door Positioning

I show you how to adjust your Chamberlain myQ garage door opener and how a garage door should open and close when properly adjusted.
Amazon associate link: amzn.to/3XAmI31
How to replace garage door seal: • How To Replace Garage ...

[@jamesskid231]

Bro... you saved the day. I was looking for an old "dial adjustment!"

[@R.Akerman-oz1tf]

Did U find the trimmer version?

[@JeromeDiaz-e5s]

There are 200 videos on this subject. This is the best direct, fully explained, shot angle video on the internet.

[@jackstraw5527]

What if it’s stuck in the open position? Having a hard time figuring out how to start the up adjustment from the down position while keeping the door engaged to the opener.

[@selvinmenjivar]

You are the best man thank you for your help.

[@huaraches702]

Mine does not stop where I set it to, anyone knows how to fix that? I can set it to stop half way down and it’ll still go all the way till it almost pushes the door out of the wall, I noticed too that I stop the door when programming it, let’s say 12” off the floor but it’ll keep going, like the chain won’t stop. Thanks.

[@Killobyte]

Not sure what to tell you on that one. 😕

[@avinachom8010]

My garage door chain popped out (didn't break, just lose screw). After reconnecting it, the door went out of sync/adjustment. You video saved my day (and probably $200 lol). BIG Thank You !!

[@mirandacollins393]

Mine is being a pain, it won’t come off lol. I need to change the bulb , I’ve tried pushing in sides lifting up then out first. Still don’t wanna come off.

[@Killobyte]

On mine, you have to grab the top center and just pull it outward. It hinges on the bottom. It feels like it might break but it hasn't.

[@mrhoya14]

Can I program the Chamberlain without Plugging in the wall button and door sensors? I tried programming the door adjustment but it just beeps no Movement..

[@Killobyte]

It appears you have to have the wall until connected.

[@Sabuz73]

Thank you so much !!!!! It helps me to fix the issue and save $$$$$$

[@Sabuz73]

I fixed it according to your directions but next day again i had to adjust it. Is there any reason it’s happening? Please advise.

[@debbieheyer7226]

Thank you!

[@Dreshan1990]

Thank you so much! Your instructions were clear and concise👍🏾👍🏾

[@troyrambo6804]

The controls on mine were different but this helped me greatly. THX!

[@DeltaTaiChi]

Thank you so much. Very clear and concise instruction. Great video.

[@alisami7917]

Thank you very much my friend, you saved me from an important problem, the problem with my garage door was solved exactly as you described.

[@SharonMoore-x7u]

Your video was insightful, did the steps you suggested, and my door is now going all the way down. Wanted to try this first, before paying someone to come out and see what was happening. Thanks!!

[@scubaeric2820]

Thank you. Couldn't find this in the manual! Door is opening and closing correctly now!!!

[@LoriM1959]

My original problem is the door will not automatically close when you push the wall button, or the remote in my car. You have to push and hold down the wall button in the garage to completely close the door. If I just press and try to release the wall button the door won't close...it's as if something is obstructing it, and the lights flash continually. If I use your method here in the video, do you think this will address the problem? When the door is completely closed, there is a gap on the right side, as if the ground is uneven, or maybe the door is messed up? Thank you!

[@nemodio]

That sounds like a safety sensor issue. Make sure the sensors near the ground on each side are lined up. It’s common for the sensor to get bumped or kicked and the garage door opener thinks there is something in the way and reverses the closing door.

[@mattb2417]

Thanks for the information it was clear and accurate much appreciated

[@AP__RE]

Perfect video! Thank you!

[@cliffmckenzie9473]

Thank you, thank you...your instructions were perfect

[@dianeelwood8542]

Our door goes up and slides back down about 6 inches - the opener will take it back up - this will happen about 7 times then it will stop . Can I adjust this ? It started when a guy came out for something and he said there was to much tension on the rod on ceiling .

[@Killobyte]

Carefully! Use the rope pull to disconnect the garage door from the garage opener carriage/traveler. If the garage door starts going down/closing, you probably need your torsion spring replaced or adjusted. Just be very careful doing this as the door could fall hard if the spring is broken or very weak. If the torsion spring is working right, the garage door will stay up on it's own until it's pulled down.

[@joeguzik4594]

Your information was excellent it worked!

[@devodar2579]

This is a great video that has helped many of us, great show!!! Thanks

[@isabellu624]

You saved my day! Really helped me solve the problem!❤

[@ltsammons]

Really good video - it helped me out tremendously!

[@timdawson4151]

Thank you, worked exactly the way you showed

[@dewanafication]

Thanks for the helpful video 👍

[@lalolalo1233]

how to make go up or down slowly? I can't figure that out.

[@Killobyte]

The quicker you press and let off the buttons, the less it will move.

[@bailemdon]

Thanks, easy to follow and did what I needed

[@fredhooshi4294]

mine is much older set and do not see the adjustmrent buttons

[@Killobyte]

Does it have something like a dial you can turn? If so, one is for closing and the other for opening, turn them until they close/open the correct amount.

[@msteciak]

Thanks for the video

[@delawareharnessrace]

Thanks. Worked like a charm

[@DaveG976]

You saved my life 🎉🎉🎉

[@adventureisoutthereforyou]

Thank you so much! 😅

[@Karthikbn11]

Why does the trolley jump when it starts closing initially? Mine does that too and it is so annoying

[@Killobyte]

I believe that is the weight of the door moving from the two side tracks (runners) to the garage door. The belt/chain rail can compress under that weight.

[@Karthikbn11]

Weight of the door moving to the garage door ? Sorry I don’t quite get it. Is there a way to fix it and is it a safety issue ?

[@greganderson1989]

Awesome. Thanks

[@carolinethompson3839]

Saved my day too

[@thecraftsmanguy1899]

Just a quick question how many garage doors do you have?

[@Killobyte]

Two

[@millikenway]

Hello, I have a further question to ask. I have adjusted the door to hit the garage floor while it was really sunny outside. However, when I tried to pump the down arrow key a few clicks trying to reduce the slits of light coming in due to the uneven flatness of the garage, this action eventually gave me problems. Under normal closing of the door it reopens as soon as it hits the ground. It probably triggers the safety function thinking that it hits something. Is there anything I can do under this circumstances? Thanks in advance for any help you may give.

[@Killobyte]

If a standard U shape one won't work, you can try a rubber blade garage door seal. You can cut them to fit the shape of the floor.

[@millikenway]

@@Killobyte Hello, hello. Thank you so much........... I just researched on the rubber blade you mentioned, I found a 3M product "16.5Ft/3M Universal Garage Door Rubber Threshold Strip, Weatherproof Seal Strip " from Amazon". I am quite sure this one would work and it also has added advantages of stopping leaves, debris from entering the garage. What a neat product. This world is so much more beautiful with people like you helping out others without even knowing who you are helping with. I am smiling while typing, YOU are a good man!!!!

[@jimmy4x4socal44]

Thanks dude

[@jamesfantjr]

Very helpful!

[@hossman333]

Thaaaaaaaank you!!

[@pedrolimaneto5573]

Thank you!!

[@jovyhenriquez2546]

Thanks