How to Remove and Install a Motor Mount In A 07-14 Chevy Suburban, Tahoe, Silverado, GMC Sierra, Yuk

[@Guffy5150]

Terence, I like how you actually show the full real time hard parts during your video. Most just cut that part out and say, "So we removed that part and moving forward now." I have never watched a video and been rooting for someone to get a part in place until your great full fight being shown. I am now going to attempt to replace mine. Thanks a million and keep it up.

[@TerenceDIY]

Thank you so much Ken. I put a lot of work and effort into my videos. Thanks for watching as well.

[@AHammbone]

Same! I just watched another video where a guy replaces this same motor mount and video just flashes ahead and he's like "WELP we got it installed 👍" ..I'm just like WHATS EVEN THE FN POINT?? 😂

[@Alanthe918mobilemechanic]

For diy this isn’t bad good job bro fr that’s what’s up saved ur self 500-1300 I do it a different way but more then one way to skin a cat

[@RuRu-o8z]

😂😂 this is overboard! Thanks Terrance!

[@TerenceDIY]

You're very welcome. Thank you for watching.

[@RegularShow93]

Just did moms. Thanks for the help.

[@TerenceDIY]

Awesome! Thank you for watching.

[@craigcharron6154]

Nice work. Thanks for the video, very helpful!

[@TerenceDIY]

You're very welcome Craig. Thank you for watching.

[@MrSupperdave]

Just wondering if you remove the cat would it be a lot easier to remove the mount or easier to pull out?

[@TerenceDIY]

If you're talking about dropping the exhaust, it would help a little because you'll be able to raise the engine a little more.

[@JasenFromBoston]

it looks like the jack that supported the motor was removed before the work was done?

[@TerenceDIY]

Nope.

[@paulsears3274]

Thank you for the video. What air ratchet/impact tools did you use?

[@TerenceDIY]

Hi Paul, I was using one of these Good Year air impacts at the time (link below). Thanks for watching. www.ebay.com/itm/204016776136?chn=ps&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&itemid=204016776136&targetid=1263433204054&device=c&mktype=&googleloc=9021629&poi=&campaignid=14859008593&mkgroupid=130497710760&rlsatarget=pla-1263433204054&abcId=9300678&merchantid=101692857&gclid=Cj0KCQjw852XBhC6ARIsAJsFPN1Dbr_4v32KnKYioqlitfLDGoT6BbYo2ldNHgwU2GYXFL25GEWL4jMaAiXrEALw_wcB

[@paulsears3274]

@@TerenceDIY Thank you. I ended up deciding to remove the power steering pump to get better access. I'm impressed you were able to get the old mount out and new one back in with the limited room!

[@TerenceDIY]

It took a lot of maneuvering Paul. I'm glad you you got it done. Thanks again for watching.

[@mark1john]

Great video....what's the symptoms of a bad mount??

[@TerenceDIY]

You can actually feel the motor lifting up during takeoff (you can hear a thump). It's very obvious. Thanks for watching.

[@mark1john]

@@TerenceDIY Yessssssssss that's exactly what I feel... It happens when I take off at a light...thanks bro 👊🏾 👊🏾

[@TerenceDIY]

You're very welcome.

[@mark1john]

@@TerenceDIY hey bro one more thing...hopefully u can assist... So Ive been having a issue where my abs and stabilitrack light has been coming on..and changed out the front hubs right after I started getting binding on my front left brakes... My conclusion is the abs module is bad... So I bought one..my question is can I install and drive with that part or must I get it programmed after installing??? Also any advice on my issue??

[@TerenceDIY]

@@mark1john , yep you can install it without being programmed. The few times I have installed them, after driving for a while, the system reads them by default. However, the abs and stabilitrak light can also be triggered by a sensor on the shock and air pump. Mines is currently doing it. I will be fixing it soon.

[@DericO-rz3be]

THANKS TERENCE

[@TerenceDIY]

You're very welcome. Thank you for watching.

[@aemulusanton3504]

Just remove the top nuts on the bracket. 15mm nut x 2. You'll need to wedge it in there after you rotate it to Access the top bolts. Just take a picture before on new bracket, mark it so it doesn't get bolted upside down.

[@annettegarcia6795]

Did you get under the truck or work by taking off the tire? We are having the problem of putting it back on.

[@TerenceDIY]

I worked through the wheel well mostly (removed the driver side wheel and fender guard).

[@grandhustle53]

Thank you for this video!!!

[@TerenceDIY]

You're very welcome. Thanks for watching!

[@jondagel6801]

@@TerenceDIY Nice video but you have to adjust your torque when you add extensions. kzbin.info/www/bejne/qoO1aml_gayCiLc

[@TerenceDIY]

@@jondagel6801 , you are absolutely correct however, I am very confident, that mount will never move. Thank you SO much for watching!

[@pauldigiorgio6373]

I don't know why you didn't unbolt it and wiggle it out the back it's a lot easier than prying it and banging it back in

[@TerenceDIY]

Hi Paul, the truck has four wheel drive. It would not have come out the back.

[@pauldigiorgio6373]

Ok I didn't realize that thank u

[@craigcharron6154]

​@TerenceDIY yeah the 2wd is much easier.....

[@Alex-ti3uf]

This procedure it doesn’t work with me, so I took off the exhaust pipes.

[@ray6976]

Did you have aftermarket headers? I dont see any reason on a stock 4x4 to remove it.