Your video was great. I was able to change the belt and adjust the motor height so the new one works perfectly. Thank you.
@whythre3 жыл бұрын
Just ordered a belt from y'all last week, and before putting it on I decided to watch this video. So many nice little tips, like protecting the paint from getting chipped, or mentioning how the belt is supposed to be loosely tensioned rather than tight. If I need more featherweight parts I am ordering from y'all!
@NedouxSews2 ай бұрын
Very helpful, thank you so much!
@catrionagroves54304 жыл бұрын
Thank you for your clear warning at the start of this video, I was watching it prior to replacing the belt on my machine and my (engineer) husband came in half way through and said "Oh, yes, simple. You just do this and that and hey presto" and I insisted that no, I have to wait til the end because I have a plastic motor pulley. So glad I did. I'm gradually teaching him that following instructions TO THE LETTER can be amazingly beneficially! Many thanks.
@donnafournier6966 жыл бұрын
Thank you for all your help with these wonderful machines. I was able to service my machine properly after having a local 'expert' missed .
@mikehoncho29494 жыл бұрын
Thanks man super informative and helpful!!
@dananutt3704 Жыл бұрын
Thank you so much for this tutorial.
@sylvia44256 жыл бұрын
My god, that is one gorgeous machine! Very shiny and well taken care of. Kudos!
@stacywest80067 жыл бұрын
Exactly what I needed, thanks!
@pennycaster88864 жыл бұрын
Many thanks!! Piece of cake, thanks to you!
@shirleyann69547 жыл бұрын
Please note in your video that once the belt is on, show tightening of the screw and how to insure it is not too tight.
@mikehoncho29494 жыл бұрын
He has another video for that.
@meganmills65453 жыл бұрын
I've removed the screw from the bakelite pulley but it will not pull off. I don't want to pry it off as I'm fairly confident that will break it. I've put in a little penetrating oil with the aim of putting it where it will creep onto the shaft (with the end of shaft/pulley facing down so none can make its way inside the motor). If it doesn't budge at all with turning and pulling are there any "advanced tips" you can share please? Or am I best at the stage just to clean it all and pop the screw back and in let that be that? Thanks for any advice from anyone, including other readers, if you've had this problem and figured out how to overcome (or have a cautionary tale!). Ta... Megan
@debbiepring22364 жыл бұрын
How do you remove the hand wheel from a 101?
@lisanelson61033 жыл бұрын
What is causing the thread to knot up on my bobbin and it cuts the thread?
@featherweightshop3 жыл бұрын
Check out the Featherweight Schoolhouse with all the categorized maintenance tutorials and troubleshooting and then contact the shop directly for further Featherweight technical assistance: singer-featherweight.com/blogs/schoolhouse
@nankc15 жыл бұрын
My motor needs to be lowered now that I have replaced the belt on my white FW so that the belt is tightened because the belt won't turn. How do I lower the motor?
@featherweightshop5 жыл бұрын
Here's the adjustment tutorial for you 😊 singer-featherweight.com/blogs/schoolhouse/adjusting-the-belt?_pos=1&_sid=29a641dbc&_ss=r
@annyoung50307 жыл бұрын
Hi, where can I purchase the belt.
@nankc15 жыл бұрын
At www.featherweightshop.com
@featherweightshop5 жыл бұрын
Here is the link to the belt for you 😊: singer-featherweight.com/collections/parts/belt