How to Remove BMW Front Axle - CV Axle on BMW E90/E92 xDrive

  Рет қаралды 57,021

SimpleCarGuy

SimpleCarGuy

Күн бұрын

Пікірлер: 75
@SimpleCarGuy
@SimpleCarGuy 4 жыл бұрын
Thank you everyone for watching. Consider subscribing for more car content! Check out why I bought a BMW 335xi: kzbin.info/www/bejne/rIbcc2lnqrCIirc
@erlomotorsport
@erlomotorsport 2 жыл бұрын
Hello. For the next time you have to remove a driveshaft. I hold the driveshaft with the oil filter release strap and lever it out. If it slips because it requires a lot of force, I put a clamp on the driveshaft and lever on the clamp. You have to push the driveshaft towards the box and give it a sharp blow with the lever to remove it, otherwise the circlick gets stuck and does not close to come out. Great video and good luck mate.
@wikwyre
@wikwyre Жыл бұрын
Did you put it back together? You only filmed half the job!
@zapata420
@zapata420 7 ай бұрын
Ive never seen a ball joint come apart that easy. This is crazy.
@SimpleCarGuy
@SimpleCarGuy 7 ай бұрын
The other side wasn’t as easy!
@ThunderbirdRocket
@ThunderbirdRocket 10 ай бұрын
Extraordinary detail ! Super helpful !! I learned lots !!! Thanks mate . 👊🏼
@michaelturner8661
@michaelturner8661 3 жыл бұрын
To break the 36mm bolt loose I use a breaker bar and a floor jack to apply force to the breaker bar. Breaks it loose with no effort at all.
@SimpleCarGuy
@SimpleCarGuy 3 жыл бұрын
That's a great idea! I'll use that next time, thanks.
@BMWBoyeeM3
@BMWBoyeeM3 Жыл бұрын
Would the jack apply the opposite force? About to do this so super interested
@BMWBoyeeM3
@BMWBoyeeM3 Жыл бұрын
Lol. I figured it out. Thanks for the idea
@bmak24
@bmak24 Жыл бұрын
genius.
@SurginersYT
@SurginersYT 3 ай бұрын
I just use an electric 1000 ft lbs torque impact gun
@chiragraju9498
@chiragraju9498 2 жыл бұрын
Thank you for the video, very helpful information here especially for home mechanics!
@SimpleCarGuy
@SimpleCarGuy 2 жыл бұрын
Glad it was helpful! Thanks for watching.
@sinohoeung8282
@sinohoeung8282 Жыл бұрын
Where do you order the plastic when you pry off and break
@bradysolaem2467
@bradysolaem2467 2 жыл бұрын
an oversized chisel usually works if its got sum to wedfe against while hammerefd
@andreyzozulya1181
@andreyzozulya1181 2 ай бұрын
Thanks for the video 📹 I have a question:is it the same procedure with BMW E 87 or not?
@aimized1460
@aimized1460 2 жыл бұрын
Does this really have to be done in order to do the oil pan gasket on these xdrives models ? What if you didn’t bang it out of there and instead proceeded to get to the oil pan and just try to drop it while removing the difff side that’s in the pan ???
@e.e9331
@e.e9331 Жыл бұрын
absolutely, one the most retarded things bmw does until now. 30$ gasket costs 1500$ with labour. i love bmws but this shit is frustrating esp on some cars leak starts even at 100kKM
@e.e9331
@e.e9331 Жыл бұрын
no other way around it you ahve to take cv axles out completely to do oil pan gasket
@bmak24
@bmak24 Жыл бұрын
great video with tons of practical advice. thanks!!
@GLPVideo
@GLPVideo 2 жыл бұрын
Any luck finding the plastic rings at the end of the axle? I can't find them
@micahdornbusch3555
@micahdornbusch3555 2 жыл бұрын
Great video but please tell me you did other maintenance
@robertbarrett3507
@robertbarrett3507 2 жыл бұрын
Hello there, I was wondering if the power steering pump is attached to the oil pan?
@711lorena
@711lorena 2 жыл бұрын
Yes
@xx_g3t_rekt__xx603
@xx_g3t_rekt__xx603 6 ай бұрын
question?, i want to make my car completly rwd, im gonna keep the outer and inner cv joints and just remove/cut off the axle, is it fine to just leave the inner joint in the gearbox or will it come out over time?
@stylestealer
@stylestealer 6 ай бұрын
Bro don’t do this, search up how to disengage the front axles by coding it. This way you can turn off x drive and be completely rwd and still have the option to go back to xdrive
@xx_g3t_rekt__xx603
@xx_g3t_rekt__xx603 5 ай бұрын
@@stylestealer i already have x-delete, i lowered the car but i want to take the axles out so i can lower it a bit more, right now the axles bend so much that they stop the car from going lower and im afraid that they gonna come out when i drive, im never gonna make it 4wd again anyways
@rbitrossome
@rbitrossome Жыл бұрын
Why do you have to take the CV axles out to remove the engine?
@SimpleCarGuy
@SimpleCarGuy Жыл бұрын
The differential is attached to the engine and the CV axles are inside the differential. So, unless you want to drop the subframe to detach the differential, this is the easier way.
@rbitrossome
@rbitrossome Жыл бұрын
@@SimpleCarGuy Ah, ok. Thanks. I'm starting the process of taking an N55 out of an F10 and your videos are a big help! Thanks for the series!
@atrank
@atrank Жыл бұрын
Any comments or views of the snap ring on the inside end of the axle? I had a specialty euro garage replace the passenger side front axle. Soon after that, I had the dealer replace the oil pan gasket and they found that the snap ring was twisted and jammed, so they had to cut the axle off!!! Now my driver side front axle needs replacing (rusty swelled ABS ring) and I want to avoid this mistake again.
@Nathan-gj8ch
@Nathan-gj8ch 3 жыл бұрын
I see you have an lower oil leak i had one like that too xdrive e92 I replaced all the aluminum oil pans bolts with longer full threaded steel oil pan bolts from a civic and the leak went away. some of the heads on oil pan just fell off when I touched them.
@chiragraju9498
@chiragraju9498 2 жыл бұрын
curious to know if you had any electrolysis issues using steel in place of aluminum? I've heard BMW strongly recommends against that
@Nathan-gj8ch
@Nathan-gj8ch 2 жыл бұрын
@@chiragraju9498 All the Honda blocks I have are alu and steel bolts if it works for a NSX with 250k miles or a d16 with 720k I'm willing to bet it will be ok on any block. I strongly recommend using fasteners that don't fall apart after 90k miles. If galvanic corrosion was really an issue then BMW and ZF would not have put steel spacers and steel bolts on the trans pan.
@SimpleCarGuy
@SimpleCarGuy 2 жыл бұрын
Hey I never saw this comment. It was t clear in the video but the reason I was removing the drive shafts was because I was removing the engine from the car. The reason for the oil you see is.. a 2 inch hole in the oil pan. I have awhile series in how I removed it and rebuilt it if you’re interested.
@edwardhenry7119
@edwardhenry7119 4 жыл бұрын
Is that the same as a 2007 328XI E92 procedure?
@SimpleCarGuy
@SimpleCarGuy 4 жыл бұрын
It should be very similar, the oilpan/transaxle might look a little bit different, but the rest of the steps are the same.
@yotaismygame
@yotaismygame 4 жыл бұрын
Thank you. On the part where you used a breaker bar to make it fit next to the boot, could you not just use an extension with a ratchet?
@SimpleCarGuy
@SimpleCarGuy 4 жыл бұрын
My ratchet’s head was too big to fit in there. Thanks for watching!
@ricoesse9364
@ricoesse9364 3 жыл бұрын
thx for the video !! what was the reason you put new axle s on ?
@SimpleCarGuy
@SimpleCarGuy 3 жыл бұрын
I took the engine out and to do that, I had to remove the axles.
@stevefriess7074
@stevefriess7074 4 жыл бұрын
Do you have a video on how to change the Front wheel bearing on a 2011 328I X Drive. There are not any videos on the xdrive wheel bearing replacement
@SimpleCarGuy
@SimpleCarGuy 4 жыл бұрын
Unfortunately, I do not. I only work on my own cars and I've never had a 328i or had to replace the wheel bearing on any of my cars. Also, it should be the same on 335 as it is on 328 as long as they are both xDrive.
@TRACY51167
@TRACY51167 3 жыл бұрын
So the BMW has a closed Transmission except for this access.... so how much trans fluid did it leak out? Do you need to refill it?
@SimpleCarGuy
@SimpleCarGuy 3 жыл бұрын
It’s the differential fluid, not the transmission. I refilled it until it started coming out of the fill hole.
@albertonunez851
@albertonunez851 2 жыл бұрын
Good work! and yes you helped me.
@isrealperez9069
@isrealperez9069 4 ай бұрын
Mine would not come out I tried so many things but it got stuck right inside there My only problem was when I picked up another one it slid right inside I didn't know if it does that mean that it'll cause noise because it was easy to slide in
@SimpleCarGuy
@SimpleCarGuy 4 ай бұрын
It’s not supposed to be hard to slide in. Maybe your old one was rusty or bent? I don’t remember exactly (it’s been years), but I’m pretty sure it’s supposed to click when you slide it in all the way.
@isrealperez9069
@isrealperez9069 4 ай бұрын
@@SimpleCarGuy it was just hard to remove but when I installed the other one it slid in like nothing like bread and butter
@tbechavez3046
@tbechavez3046 3 жыл бұрын
Do you need to give her a realignment afterwards? Since you didn't twist the tierod
@SimpleCarGuy
@SimpleCarGuy 3 жыл бұрын
Nope, not needed as long as you remove the wishbone from swivel bearing only. If you remove from the other side, you'll have to get an alignment.
@stehlfamilyfarm6886
@stehlfamilyfarm6886 11 ай бұрын
I've never had a bmw ball joint come out that easy lol
@Bigguccitana.
@Bigguccitana. 2 жыл бұрын
Can you drive an xdrive without the front axel?
@SimpleCarGuy
@SimpleCarGuy 2 жыл бұрын
Technically, yes. But I would definitely not recommend it. You would have oil leaking out of the front diff etc. The drive shaft might also be doing some kind of support for the wheels.
@Bigguccitana.
@Bigguccitana. 2 жыл бұрын
@@SimpleCarGuy my biggest concern was support for the wheels after removing the front shaft but I’ll just replace it instead
@JayDee-b5u
@JayDee-b5u Жыл бұрын
@@Bigguccitana. The vehicle does not need to support the front wheels from the drive axle. If you look at the rear wheel drive models they have all the same components but without the front drive axle. I figure if you could seal the area where the drive axle is connected to the front differential you would have a rear wheel drive model but with the added weight of the front differential.
@McCulloughSim
@McCulloughSim 4 жыл бұрын
Can you make a list of all of the tools I’ll need?
@SimpleCarGuy
@SimpleCarGuy 4 жыл бұрын
You'll need a standard mechanic's tool set to remove some nuts on the suspension. At the very least a wrench set going all the way to 24mm. Specific to this job, you'll need the axle nut wrench. I have links in the description!
@scottcrawford4148
@scottcrawford4148 2 жыл бұрын
It must have been hard to record that process on video - thanks
@mokuii8338
@mokuii8338 4 ай бұрын
My passenger side cv axel cane off as i was driving lmaooo idk how but i got a new one
@autohut3720
@autohut3720 4 жыл бұрын
Man getting that axle out the differential is a royal pain in the ass. I was doing the passenger side and it’s even worse I think
@SimpleCarGuy
@SimpleCarGuy 4 жыл бұрын
Oh don't I know it! The passenger side was worse, strictly because it took me good 20-30 minutes to get it loose.
@Sti.king2k
@Sti.king2k 3 жыл бұрын
What about the fkin passenger side
@SimpleCarGuy
@SimpleCarGuy 3 жыл бұрын
Exactly the same thing!
BMW F10 xDrive Front Axle Replacement
9:21
East Coast Garage
Рет қаралды 102 М.
小丑女COCO的审判。#天使 #小丑 #超人不会飞
00:53
超人不会飞
Рет қаралды 16 МЛН
BMW 328i CV AXLE "QUICK AND EASY" REPLACEMENT
17:57
Heartland Mechanic
Рет қаралды 30 М.
BMW E90 ABS Fehler / Antriebswelle und ABS Sensor ersetzen / E87 / E90 / E91 / E60 / E61
18:03
Bimmer Technik / Coding / Service
Рет қаралды 44 М.
How To Perform a Drivetrain Service on a BMW N54 335xi | DIY
11:35
Understanding the basics about fuel trims
23:43
Hands On Auto Training
Рет қаралды 119 М.