How to remove curb rash on any rim with a rotary polisher

[@ak2112]

nice work! I'd definitely do this if I knew my wife wouldn't demolish the wheels again moments after I finished.

[@cvrpov]

Can't help you with that one bud

[@FassEddie]

Sounds like she needs some steelies and a set of Wal-mart covers.

[@on-site4094]

Ak2112. Thanks for pointing out most of deal with 😂 U gotta love him

[@bubffm]

Just admit it: Its you!! 😂😂

[@shucker]

I call BS on any guy who says he hasn't run up against a curb and damaged a rim.

[@CatsBanana-1983]

Amazing! I was looking at picking up some scuffed wheels from the junkyard, but I was hesitant since I wasn't sure how to handle refinishing them, but now I am more confident buying them. Thank you for the video!

[@cvrpov]

Glad I could help!

[@MTL_Rider]

Great job for a DYI at a lower cost. I've done this a couple of times, but I find it chips and scratches very easily. On my last set of mags, I had them professionally powder coated for $400, finish lasts longer and scratches less with normal wear and tear.

[@cvrpov]

If you already havnt. Recommend using a good 2k lacquer. Powdercoting is good, but one little nick and your back to square one.

[@faol4n654]

As a Car Mechanic myself and one who did Tire-Jobs and more for a long time I need to make this recommendation: 1. Make your life much easier and get your tires to a Car Workshop so they can press down the Tire from your Rim... if so, you don't have to be that carefull to hit the Tire while sanding, also spraying the Rim afterwards is much easier and the Finish is much better since you can get deaper in the part where Tire and Rim hit each other. Afterwards you just have to fill the Tire with air again and normaly it just should pop up into old position ;) 2. After doing all this... also get to a Car Workshop or a Wheel company, to let your Wheels be balanced again... since you remove and also apply material to your Rims (Removing Aluminium and applying paint) they might be outbalance at least a slight amount. Especially on front wheels where your stearing is, you might find this out sooner or later. Also it's not this nice for the Rest of your car to have these vibrations cause your wheels are off balance. But without these, it's great job ;)

[@cvrpov]

Yep 👍🏻

[@teslacybertruck750]

Your work is incredible, this is what I call a top of the line curb rash repair, un like other uploaders who claim to fix curb rash and all they do is paint over the damage

[@cvrpov]

Thanks for watching and feedback

[@krisscarborough6823]

As someone that does this for a living day day out it’s good instructions very knowledgeable. The only goof up is using primer. If you notice most rims have 0 primer it’s not needed and is just a layer that can cause problems. As someone who’s been in auto body for 17 years trust me I know it sounds wrong but feather put your damage and paint right on the metal.

[@cvrpov]

I dont usually use primer. I was trying to be "pc" for the video. Agree with ur points

[@65Wri]

@@cvrpov As an ex painter, you need to read the instructions on the paint you are using if primer is required for the bare metal, manufacturers will use paints created to suit the wheel material to save time and costs. you don't want the paint start falling off the repairs at the 1st chip or scratch. I think most paints are 1 step now but do check

[@daos3300]

etch primer is a good idea on ally for decent adhesion. more particularly in cases like this where the substrate is mixed - as you can clearly see the manufacturer used both primer and colour.

[@andru2625]

Thanks a lot for the video!. I just damaged my front wheel and by using sandpaper with water I was able to remove 95% of the curb rash.

[@cvrpov]

Nice one 👍🏼

[@nailz84]

I cant believe iv only just discovered this channel recently the videos are exactly the stuff I love to watch I have an older 2003 Volvo v40 and I love to keep it looking good but I have to do all of this on a budget as my kids always have and will come first. This is a great channel that really explains things fantastically....definitely makes you wanna do it yourself.

[@cvrpov]

Great feedback 👍🏻

[@deterrentdubz9116]

Good on you putting the kids first! Love to see it, also hope your Volvo is in tip top shape and brings you joy when you drive it!

[@eddiecz]

You're the Chrisfix of our nation 😂 love it mate deffo gonna fix up my alloys in a few weeks with this video on repeat!!

[@cvrpov]

Haha I've a long wag to go before I reach anywhere near Chris's level. I need more subs!

[@brucewayne2773]

I take my wheels to the tire store to get them to break the bead, this greatly eases the entire process. Use red scotch brite pads to scuff up areas that does not need repairs . i use an orbital sander with 120 grit and that is all you need to repair the curb damages. Wet sand with 320 grit on a pad to remove any swirl marks. Use a large trash bag cut a hole and wrap the wheel, it takes a minute instead of using tape to mask around tires.

[@cvrpov]

Everyone has their methods

[@cpzmelbs]

I think youre overestimating how many people have an orbital sander

[@Lee-xm1cu]

@@cpzmelbs That's not an orbital sander.

[@cpzmelbs]

@@Lee-xm1cu is that a setup for a joke or.. what are you trying to say exactly

[@cessealbeach]

Yes , I did use your technique, results were fantastic, Thanks! unfortunately my wife did it again, rear wheels this time.

[@avguylyfe5837]

I just did this. I went another route. Got a set of metal filers. Filed it down to a smooth surface. And just used touch up paint. Came out pretty good and quick. Finding the color match is always trial and error

[@cvrpov]

Whatever works

[@smileplease444]

Can you share a video of what u did

[@roddagaud5341]

@@smileplease444 I wanna see too

[@maxscarblog]

All German brands use Wurth silver wheel paint, which is also very close to VW reflex silver.

[@c50ge]

I built a “lazy Suzanne “ out of a base off of an old junk swivel reclining chair. Flip it over so that the round base is facing up. I can easily rotate the wheel to evenly cover the entire wheel without making 50 laps around the wheel. I used to end up with some areas that the paint was a bit thin because i could not see some places.

[@cvrpov]

Awesome story

[@RealityRenegade-bv2ww]

It's called a Lazy Susan, bruh.

[@RealityRenegade-bv2ww]

It's a Lazy Susan, brah, not Suzanne.

[@c50ge]

@@RealityRenegade-bv2ww okie dokie !

[@Johny40Se7en]

Wonderful job, and great on you for sharing the playing card tip. Reusing a pack of cards is way cheaper and reduces waste than using masking tape. Respect fella 👍

[@cvrpov]

No problem thanks for watching

[@brandsolutions6562]

I have been looking for a video like this for Ages! I am f glad I found it.. Could you please add a few more HashTags in your video so other people can find it easily? You are a Legend mate!

[@cvrpov]

Thanks for watching!

[@smurfsmurf2295]

Absolutley brilliant very well explained unlike others I’ve watched well done sir great job

[@cvrpov]

Thankyou

[@poplaurentiu4148]

@@cvrpov This method can not be applied on rims that have dymond cut-face specially if the owner wants to look the same because in dymond-cut face of wheels the tires need to be removed from rims then rims taken to a CNC face machine to reface the lip, then the wheel need to be rebalanced after tire was mounted on..

[@matthewbroder6689]

Nice job, I would use etch primer for bare aluminium to aid the bonding.

[@cvrpov]

This can help yes

[@dogbite5509]

This is a fantastic video. You can use a small piece of hose to mask the tyre valve.

[@cvrpov]

Thanks for watching and good tip

[@petergumataotao6811]

Hello great video I was thinking of repairing my curb rash but was wondering will this throw off the balance of the wheel? Ne advice is helpful. Thanks again.

[@scotttheodore9732]

That was a very good job. The finish looked like factory and you can’t really tell if the wheel was ever touched up.

[@cvrpov]

Thanks for watching

[@toddhoodenpyle3264]

You are a world treasure, sir. PRIMER question: regular, or filler type? I guess it depends on level of damage on face, but wanted your thoughts. My focus is the kerb rash, which the eye is naturally drawn to first. Cheers from Oregon, USA!

[@cvrpov]

The best primer you can get your hands on and budget suits. Some filling properties would be a bonus but always make sure your prep is as good as u can get it and don't rely on primer to hide marks you've left

[@peterrenn6341]

It's a Volvo, so the owner will curb them all again by next week 🙂

[@RiseKeyk]

awesome! I needed an excuse/reason to buy a grinder so the wife wouldn't get mad. thanks for the video!😊

[@cvrpov]

Haha glad I helped with the grinder purchase. This was a rotary polisher used in the video though just making that aware

[@michaelmclannahan1165]

Great job! Would you recommend they’re rebalanced after this sort of work is carried out?

[@cvrpov]

Ideally yes. Altho in theory a wheel is unbalanced after being damaged anyway.

[@mikeyincalif]

Great job guy ! I have a Chrysler crossfire convertible I’ll be doing this to. Waiting for a sanding kit for my impact drill. Thanks

[@cvrpov]

Thanks Mike 👊🏻

[@sidwilson9556]

Brilliant job. Wish I had the patience todo it. Amazing video. Thanks 👍🏻

[@jibmaster]

Curious how you prevent overspray to the inside walls when spraying. Great channel

[@v3rsatle]

Finally a video that explains everything and show you what to buy. I love you man gotta repair my Supra wheels this summer can’t wait !!! Where do i get the rotary tool itself!? I looked on Amazon but will it fit the kit you sale?

[@cvrpov]

Welcome aboard mate. Any rotary with variable speed will do. Just get a cheap one off of amazon. Most should be m14 thread which fits the www.paintgear.co.uk backing plate 👍🏻

[@v3rsatle]

@@cvrpovnice i just ordered one on Amazon right now. Would you be able to see if it fit if I’m able to send you a picture some how on IG or something?

[@CanariesExplorer]

Very good work and a great result. By the way, it's KERB as in the pavement kerb not 'curb'which is a verb which means to moderate or lessen.

[@cvrpov]

I'm better at fixing cars than writing, clearly

[@mr.b4444]

In American and Canadian English, the noun meaning the edge of a sidewalk or roadway is spelled curb.

[@CanariesExplorer]

@mr.b4444 Strange English in North America, however this channel is by an English guy.

[@MrGalaxypiano]

Thank you so much for the time you take to share this excellent work with us Keep up the good work 💪😃

[@cvrpov]

feedback like this keeps me going

[@MrGalaxypiano]

@@cvrpov please do your best Many people have benefits of your good work Keep going 😄

[@paulrowley71]

Good to see a proper thorough repair being shown rather than various faddy quick fix methods.

[@cvrpov]

Thanks for watching 👍🏻

[@philtucker1224]

A really lovely job! (If you use playing cards, always face them downwards to save spoiling the playing side 😊) happy days..

[@cvrpov]

Haha good tip and thanks for watching

[@kelstra1997]

Good video and a great result. Just one point 2K clear isn't lacquer - it's polyurethane based.

[@cvrpov]

We call it 2k lacquer here

[@janeblogs324]

Its like Muricans calling any clear shellac , they only just stopped doing it recently. Takes 30+ years for the old generation to die off and the new generation actually reads the paint can

[@Tony95192]

Great video. If you had a few deep marks on the wheel that are purely cosmetic. Can you recommend a type of filler, if thats at all possible? Also, is it an etch primer that you used please?

[@cvrpov]

I have used normal body filler before. Also 2pac mitre fast glue with activator (did a video on it also). I use normal primer. Etch is obviously probably the most proper way of doing things but I find it a bit overkill

[@ShoresMobileWashandDetail]

Thank you so much for your great videos. Hello from California! QQ. How long did it take you to restore the rim? And is that a service you offer? Thanks again.

[@simonw7284]

Thanks for the video. Two front wheels have the same curb damage, however may just take it into a Pro... Although I do have an angle grinder.... thanks for sharing. Would you recommend the wheels are re-balanced or its so minimal that this shouldn't be needed?

[@cvrpov]

Safety 1st obviously but if its very minimal then perhaps won't need balancing

[@brentonmeadowsvk3cm]

Outstanding tutorial cheers Brenton from Tangambalanga Victoria Australia😊😊😊😊🇦🇺🇦🇺🇦🇺🇦🇺

[@cvrpov]

Thanks Brenton

[@HOLYMOTHERGOD]

Good work. Could you demonstrate how a brushed effect wheel could be fixed?

[@cvrpov]

I have done loads of wheel repair vids mate check out my playlist

[@scopex2749]

A handy tip a car body specialist gave me to mask tyres EASILY cheaply and with no mess with load of old masking tape. Using a 1 or 2 inch paintbrush and a cup full of plain WASHING UP liquid - paint the tyre sidewall up to the rim with the soap - allow to dry - then spray the wheel. When the paint dries simply hose off the soap this also makes the tyres look good and leaves them clean and dirt free. TRY IT!👍👍

[@MikeWrenches]

A few years back I bought a set 20+ year old Subaru STI goldies which had some curb rash. I made a mold from an undamaged part of the lip and used that to profile Loctite PC 7264 aluminum repair epoxy in the damaged areas. The wheels were then refinished in their classic gold color. That was curb rash repair, what is shown here is not curb rash repair, no "repair" has been made, the wheel was just further damaged to blend the gouges.

[@cvrpov]

It's defo a repair mate. And thousands of people do it this way all over the world

[@MikeWrenches]

@@cvrpov Would you consider it a repair if you got into a fender bender and instead of pulling the dent, the body shop just pushed the rest of the fender in to match the dent?

[@bsargent]

Great video. Thanks for putting this together. What colour did you use? I also have a Volvo and want to give this a go. Thanks again.

[@cvrpov]

Ford moondust silver is a good all rounder

[@jcruhrskov194]

I would probably use ChrisFix' solution with a rotary tool from Dremel and a 120 grid sand paper-roll to even out the scratches. And you don't even have to be careful about the tyre wall. With the showed solution you've got here, your rim is taking a new form + potentially damage of the tyre as you mentioned. This looks dangerous if you're not somehow qualified or at least got some experience.

[@duckula67]

Great video. Should you not wet Sand with a high grit before applying lacquer though?

[@cvrpov]

No. You could wet sand with 1000 grit if u like

[@beaunicholls8856]

Beautiful work I have to wonder what just buying a new wheel would cost that’s a lot of labor time, paint, lacquer, primer, 5 kinds of sandpaper 🤷‍♂️

[@sgnt9337]

End result looks great!!

[@cvrpov]

Thanks

[@trentmaxcell4691]

Is it neccesary to deflate the tire before working on the alloy rim? your new subscriber from Canada. Thank you.

[@cvrpov]

If you can yes it does help definatley. Thanks from 🇬🇧

[@Detailguy101]

I did detailing for 15 years on high end cars and daily drivers that was enough for me glad im done!!!!!!!!!!!!!

[@cvrpov]

Graft mate

[@norbertbarsony4280]

Nice just checked a price of the compressor and the grinding disc and the angle grinder, That is already covering full alloy wheel refurb in my local garage but thanks!

[@eu4iya]

you will always have use of a compressor in the future in my opinion so it is worth it

[@idontunderstand5379]

Hi how much time approx will take per Tire? Please Thank you amazing video👍

[@Invis_Space]

@2:01 I love how even your cat was impressed. Cat: weow 🙀

[@cvrpov]

Thtas my 3 yr old 😅

[@Invis_Space]

@@cvrpov 😂😂😂😂😂 this got 100% more wholesome.

[@cvrpov]

Haha real life mate

[@dathyr1]

When you are all done, we are all ready to get more Rim Rash.

[@cvrpov]

Ok lol

[@dathyr1]

@@cvrpov I was just kidding. You did a great job of making the RIM look like new again. Thanks for the procedure. Take care.

[@Gts2pro]

Oh I wish it was so easy 😂. For me it’s going to be really tricky 😂. Thanks for sharing

[@AdmiralStoicRum]

Remember, you are removing material from the wheel, so once you've finished you should immediately get your wheels rebalanced or youre going to have a weird ride

[@Jmg831]

That’s if you didn’t take so much that it’s impossible to balance anymore 😅

[@panosdelta8384]

Nah it's a tiny amount.

[@cvrpov]

Yep. Said this many times

[@Anthony-nv7gd]

Wouldn’t that imply you should have your wheels rebalanced every time you scrape a rim anyway?

[@Jmg831]

@@Anthony-nv7gd only if you break a chunk out of it 😅

[@1one3_Racing]

That's great and all, but depending on the depth of gouge and placement you'll be taking a large chunk of material off one section of the wheel and possibly none in another meaning the bead edge will be asymmetric

[@cvrpov]

You can use filler or some 2pac glue. I did a video on this method. Check out my playlists

[@thomasharris5151]

😎I would’ve just cleared the wheel after the repair… from the video it looked better before he painted it. But either way it’s a great tutorial!

[@cvrpov]

Thanks.. i think?

[@sebastianrc5024]

Excellent, will this be the same process for aluminum polished rims?

[@cvrpov]

I have more videos that might help in wheel repair playlist

[@bp1169]

You did a good job of outside of the wheel but you do the inside of the wheel which would have had a lot of over spray?

[@cvrpov]

Mask off if needed

[@dondeestasquenoteveo]

great job! remember to check for balance afterwards

[@webmastersof]

Where did you get the "factory" base coat color from?

[@nickmcivor]

Do you have a link for the products you’ve used please?

[@hugochka]

Fantastic video. Very well explained. Will do mine soon!

[@cvrpov]

Cheers

[@freddaniali]

That is an excellent job! Great video!

[@cvrpov]

Cheers Fred

[@AdmiralStoicRum]

Looks lovely, with a good sidewall shine, those wheels would pop

[@cvrpov]

I think so too!

[@grill1234]

Wow! Nice. What does materials add up to? Discs, primer, paint and clear coat ….

[@cvrpov]

I do my paintgear kits which inc all discs, backing plate and scotch for 19.99. I think you could get the lot for £40.00 which is less than 1 wheel repair

[@grill1234]

@@cvrpov That sounds cheap - 👍🏻 Thanks for your reply.

[@edwardwilson4974]

Thanks for this! Is the speaker from Mansfield by any chance?

[@cvrpov]

Haha yes I am round that way nowadays

[@atillakhun3697]

Thanks for your nice detailed explanation. 👍👍

[@cvrpov]

No problem Thanks for watching

[@charlesedwards4160]

Well done lad, good video and enjoyable music.

[@cvrpov]

Thanks for watching mate

[@Xterra_Prius]

Amazing work, how much you charged for such job ?

[@cvrpov]

About 280.00 at the time

[@harveysingsforyou]

Wow, you really know you're stuff, excellent !

[@cvrpov]

Thank you! Cheers!

[@jameswalter3136]

Nice job! How do handle the inner 'barrel' of the wheel? Mine are full of brake dust, grime and grit.

[@cvrpov]

Give them a good clean up. I did a video on this with some spraying at the end of it. See the playlist and wheel repair section

[@mikehartwick8499]

I'd like to see that wheel spinning, you'll definitely be able to see the sanded lip.

[@cvrpov]

Bet you won't

[@isrealperez9069]

That's great buddy I've enjoyed your video

[@cvrpov]

Great

[@maxmiles7872]

Awesome job mate. Thanks!

[@MATMANPRO]

nice one mate, I would have dressed the tyre for a full finished effect.. I just subscribed, cheers from down under.

[@cvrpov]

Yeah I like a dressed tyre but being a sprayer it's like poison to us

[@MATMANPRO]

@@cvrpov cheers

[@numale100drummer]

Great demo and video, well explained! one question, did you remove clearcoat at the start and how did you remove it?

[@cvrpov]

No. Just key up old clear as long as its stable

[@sylvainlaurence1554]

It’s not gonna pass a winter without pealing. Only good for summer….

[@4s-ter]

Great video.

[@cvrpov]

Cheers

[@kianward5999]

that was just stunning bro what an amazing job done and great content bro

[@cvrpov]

Thanks Kian

[@garyfox8701]

Good work and a great tutorial.

[@cvrpov]

Thanks Gary

[@SirGregoryFamilyYouTube]

Does this work on Toyota's Chromtec wheels? For those unfamiliar with Chromtec, they are standard alloy wheels, but the outside face has a chrome-plated plastic decorative cover permanently glued to it.

[@cvrpov]

I would say not no

[@karolfrybes3633]

Hello, the question is what rotations of the angle grinder are for this process

[@cvrpov]

Hi. It's a rotary polisher and as fast as you feel comfortable with

[@rimfixer]

Awesome quality of work!!!

[@cvrpov]

Thanks

[@scottcrawford4148]

You make it look easy!

[@WaynesAdventure]

Nice work!!

[@cvrpov]

Thank you! Cheers!

[@davids.watson7342]

Not surprisingly it’s a Brit talking about that topic. Everything on roads and streets is made to destroy rims in the UK (mainly London though). It’s a government obsession to put concrete blocks on either side of narrow streets seemingly to « limit » circulation…

[@cvrpov]

Our roads are shocking. Simple as. My videos help to save people money when the inevitable happens

[@KLRGamingTeamKLRG]

Hey, Don't we have to remove all existing paint before applying the primer?

[@nbautocare1481]

Great job as always

[@cvrpov]

Thanks pal

[@sesamone]

Yo nunca lo hice, me da miedo hacerlo. Será seguro?

[@cvrpov]

Take your time

[@Mark-ob1dh]

Subbed liked. Gr8 quality content. 1 question. Audi wheel colour. Which is the brightest that can be bought in the UK. I thought ford star dust silver was brightest ford did.👍

[@cvrpov]

Thanks for the sub 👍🏼 i sometimes use audi 8z8 for wheels.

[@Mark-ob1dh]

@@cvrpov diamond silver. Yeah you know your stuff.

[@mreightytwenty8709]

Your the MAN....stay safe mate

[@cvrpov]

Thanks for the support buddy

[@In2oil2]

at 2.06 we could see your cat... great video

[@cvrpov]

It's my youngest son actually 😅👌🏼

[@zunbunn116]

Did you leave the car jacked up when painting the alloys or did you put it down? Thanks.

[@phreaktor]

What psi did you run the gun at? What gallon and SCFM compressor? I’m wondering if mine is suitable at 15 gallons and 4 SCFM @90psi.

[@cvrpov]

It was a 90 litre abac 3 hp compressor.

[@cvrpov]

Belt driven

[@313-v8b]

I'm about to purchase a Ryobi ROS300 300W Random Orbit Sander, would this give the same desirable finish? Planning to restore a few set of wheels

[@cvrpov]

Yes it will. Rotary is much quicker however

[@impdom3556]

Very nice. What tape do you use for tires? Nothing seems to stick!

[@cvrpov]

Wipe wheels with thinners and a rag 1st. I did a short on this

[@ismael9841]

nice job mate

[@cvrpov]

Thanks for watching!

[@carlospicywenr]

Hi mate - great vid! Do u have links for your air compressor and spray gun? Cheers. Alex

[@cvrpov]

compressor abac 90ltr 3hp belt driven. devilbiss sri pro

[@carlospicywenr]

@@cvrpov cheers mate!

[@HenauderTitzauf]

Elk, just do like some are doing in 2021. Doesn’t matter what they look like, JUST USE BLACK SPRAY PAINT. I certainly do not like the current flow of things, about the black wheels. If I was to want black wheels, I’d get plain steel wheels, and paint them. I do like what is done here, and I’ll keep the method in my mind for future use, if needed.

[@cvrpov]

Sounds crap to me. Thanks for watching

[@tayoidowu11]

With the sanding, can you use a sander rather orbital, or does it have to spin

[@cvrpov]

Both will work but something that spins offers better cut

[@ocdgifgandalf3352]

Beautiful job! However can't help but think it would be worth removing the tyre from the rim first so as to completely avoid any tyre damage while sanding, and saves masking up when painting.🤓✌

[@cvrpov]

True, but that wouldn't be very DIY

[@officialWWM]

@@cvrpov you can easily remove the tyre yourself!

[@gaurasrspublishing]

@@officialWWM No.

[@officialWWM]

@@gaurasrspublishing lol, yes! I do it all the time!

[@gaurasrspublishing]

@@officialWWM You may do it all the time, what makes you think that everyone else does/can?

[@gregking4395]

Really great video very informative thanks a lot 👍🏿

[@matthewnicholas6365]

What did you do behind the spokes and in the barrel? Mine are cruddy and disgusting so would think they'd need to be sanded down and refinished too? I'm not concerned about cosmetic, more that the fresh new finish on the front won't seal and will eventually peel off around the edges?

[@cvrpov]

Yes these areas will need flatting and leveling out you are correct in what your saying. Sand any damaged or flaking paint and apply a top coat