you sir saved me a good amount of money teaching me to repair this my self THANK YOU!!!! so everyone is aware be careful removing some of these clips they get brittle
@diversity27396 жыл бұрын
Welcome
@michaelrehkop48178 ай бұрын
Push down and hold the wired clip on wire harness at back of the intake. This will take the wire away from plastic locker pins. While holding clip down wiggle Connecter and gradually begin to start pulling the harness at the plastic until the harness connection separates. Installation is easy, just plug in the connectors ends together.
@fakiirification7 жыл бұрын
Oil on the plug boot. that means you need to pull that valve cover and replace the gaskets on that too. Im about to do the same job in a few days. Good thing is that you can do it all at the same time, plugs and gaskets. Save a load of work later taking that intake off and putting it back. just wish the damn valve cover gaskets didnt cost $100 bucks. tempted to just RTV it.
@christianastrophobe5 жыл бұрын
Good instructor
@diversity27395 жыл бұрын
Thanks
@howardmurden87233 жыл бұрын
lot of work....lot of patience.... Kia for sale
@diversity27393 жыл бұрын
ya, Howard I no, sold it.
@diversity27393 жыл бұрын
sorry ,I know
@qrs_tuv19256 жыл бұрын
many thanks for this outstanding production
@diversity27396 жыл бұрын
julian grey welcome Julian
@simpleshoereviews46366 жыл бұрын
diversity2 is this van Worth buying knowing you have to do all this to change plugs
@diversity27396 жыл бұрын
David Spady l would not buy it if l was not a mechanic.
@BigAlWillis5 жыл бұрын
excellent vid. I've done this job & doing it again soon on the same van. still running good just have an intake gasket vacuum leak so changing the plugs, wires, valve cover gaskets while I'm in there.
@diversity27395 жыл бұрын
Good stuff! Will it be on KZbin. sounds great
@BigAlWillis5 жыл бұрын
@@diversity2739 probably not. I don't have a nice camera, plus will be doing it short on time so I can use it for work. I don't think its needed because already a few DIY vids of it. vids like yours helping a lot of people.
@diversity27395 жыл бұрын
@@BigAlWillis ok
@adamw85 жыл бұрын
Thanks for the video, I couldn’t have done the job with out it. 👍
@diversity27395 жыл бұрын
Welcome Adam
@zandazanda25125 жыл бұрын
Great video, meticulous and detailed, BUT, that metal clip holding the harness to the sensor was not meant to be removed like that to remove the harness, It was supposed to the squeezed down first then pull on the harness while squeezing it down. The harness is then easily pulled out, the metal spring remained in place
@diversity27395 жыл бұрын
good stuff! thanks Bernard
@joeltysver68117 жыл бұрын
I'm doing this for a good friend in the next cpl days and your video was very helpful. Thanks for sharing your experience. Wondering if you changed gaskets out, and just a heads up here, you need not remove those horseshoe pins from the electrical connectors. Just push from the top and pull on wires!
@diversity27397 жыл бұрын
Joel Tysver thanks
@mariegrose56917 жыл бұрын
The clip u pulled out with the screwdriver didn't need to be removed it is a squeeze clip. The side that has the bar across it, just push it in and pull plug back
@diversity27397 жыл бұрын
Thanks Marie
@LodniKranazon5 жыл бұрын
Thanks very much for this video set!
@bugzie-a17698 жыл бұрын
All that work to replace 3 spark plugs, unreal
@diversity27398 жыл бұрын
ya I know!
@fakiirification7 жыл бұрын
Modern engineering! woo!
@Scott64a7 жыл бұрын
LOL worth paying someone $250 to do this. The more you start pulling things off in a 180,000 mile old engine, the more stuff you end up replacing. BTW, that motor looks nice and clean!
@diversity27397 жыл бұрын
Scott Roy hey l had a wonderful time during this, it was relaxing. thanks for watching.
@Scott64a7 жыл бұрын
Working on cars is relaxing to me as well, just not when hoses crack and other stuff breaks taking a manifold out. Good video, glad you posted it. Good stuff man.
@JuanRamos-nk2zd2 жыл бұрын
Buenos días tengo una kia sorento 2006 se reparo el motor pero no pendre ya la an armado 2 veces y sigue igual sin prender
@diversity27392 жыл бұрын
Buenos dias. Senior
@joshuabennett953410 ай бұрын
Thank you sir
@diversity273910 ай бұрын
welcome
@JanYi20235 жыл бұрын
Thank you brother and god bless.
@diversity27395 жыл бұрын
Welcome Sam
@rgonzalez95015 жыл бұрын
Excellent video, crappy kia design.
@diversity27395 жыл бұрын
Thanks
@livenfree5 жыл бұрын
Would u think it would save a lot of time to do the timing belt at the same time?
@diversity27395 жыл бұрын
Sounds like a good idea to me.
@BigAlWillis5 жыл бұрын
I did the timing belt & water pump. get OEM kia parts, also new Kia tensioner. dont use aftermarket if they fail your motor is toast.
@diversity27395 жыл бұрын
@@BigAlWillis thanks Jason
@80stavros4 жыл бұрын
THANK YOU
@diversity27394 жыл бұрын
Welcome
@bellalylopez70487 жыл бұрын
saludos amigo gracias por sus aportes... queria saber si me puedes ayudar, en decirme como va colocado el sensor que va detras de la mariposa, ya que lleva dos puntas y realmente no se como va gracias...
@diversity27397 жыл бұрын
bellaly Lopez denatha senor!
@chicanopridealvarez13857 ай бұрын
Does this van have a 02 sensor by the firewall?
@diversity27397 ай бұрын
didn't notice at the time I had it.
@raultorres43264 жыл бұрын
good morning I have a 2005 kia sedona has a bug in the spark 3 disassemble and has oil in the mouth 3 of the gas outlet that is a problem of arros if you can help me thanks.
@diversity27394 жыл бұрын
Sounds like blown head gaskets to me.
@bugzie-a17697 жыл бұрын
i will never buy Kia that model, forget it lol
@simpleshoereviews46366 жыл бұрын
Mario Theuma why
@builtdesigner7 жыл бұрын
I tried doing a fuel test on my sedona and can't find the schrader valve. do you know if yours has one? mine is an '03.
@diversity27397 жыл бұрын
Danny Wilder hey Danny I sold the Van. but I hear it's under all that junk.