How to Repair Broken pinion in Beautiful Way

How to Repair Broken pinion in Beautiful Way
#Brokenpinionrepair
#beautifulpinion
#Repairbrokenpinion
#amazingtechnologyprocess

[@DavidVining1]

When you have nothing, you have nothing to lose. The driver who overloaded his rig and broke the pinion the first time, will snap this one the first time he pops the clutch.

[@stevecarlisle3323]

Or Sooner. Making things "LOOK GOOD" IS NOT a repair . He could have saved doing the job Twice, by buying factory parts, and ran it for another 25 years.

[@ta-zm7tg]

Maybe or maybe not i fixed a pinion basically the same way for a piece of farm equipment it lasted about 5 years needed the part right away no one had it "fixed" it then got the factory part and waited for the fix to die factory part sat on shelf for 4 and half years.

[@stevecarlisle3323]

@@ta-zm7tg I dont think you understand much about metalurgy.

[@classicmoto2429]

@@stevecarlisle3323 I do,and I can tell you a quick repair will get him back on duty, like the prescriber wrote (is that the right word? I'm not english native), but to be honest: your right as well. So, the point is: do I have the possibility to use OEM parts or better Manufacturer part or do I have to rely on the bits I got back repaired. I often don't agree with the methods HOW they do it in these videos, but the do it and it lasts...well...quite a time... by saving a lot of money they don't have. So, to sum it up, you're both right. Let Karma make a decision

[@stevecarlisle3323]

@@classicmoto2429 Well thanks for your input, but being a heavy duty mechanic and welder, for 4o years, and certified in both trades, my best guess is it may look good, but it will have no durability. If it makes you get out of a muck hole on the farm, then it would have some benifit.

[@drd1924]

The one thing they did right was to check how parallel their welding rods were before welding

[@mikewithrow2271]

LMAO!!

[@nilos21k]

They're not using cutting oil. Wonder why?

[@A3rd3ye]

@@nilos21k it is probably a cast iron pinion. Cast iron has a high enough graphite content that it essentially self lubricates as you cut it. A lot of the maching I do on cast iron cylinder heads is done dry for this reason. When a coolant or cutting lubricant is used, it sometimes makes it harder to cut it. The only downside to using nothing is you should definitely wear a respirator or dust mask, you do not want to breath in that cast iron dust.

[@Airman..]

@@A3rd3ye no way, it's always a forged

[@wilsonrawlin8547]

@@A3rd3ye That pinion is forged or machined from billet steel alloy. Cast iron is too brittle.

[@vladimirkulakov3511]

Офигеть, сам токарь итд 5,6 разряда, всю сознанку в ремонтном производстве, но такую шнягу вижу впервые, и, дай бог в последний раз.

[@StereoSonic.]

Да, уж. Кустарщина дикая...

[@user-bi1tz2fl9k]

Одно торможение двигателем на спуске или на первом же подъёме с их перегрузами эту деталь срежет так же как и новую, закаленную.

[@lyaoninlyu7167]

@@user-bi1tz2fl9k Там, примерно, еще на два ремонта ))

[@user-yg9qq8ks4y]

А из пластилина можно разноцветный красивый вал слепить.

[@judagoldstern1720]

Да после такого ремонта там сталь и так как пластилин.

[@DummyAccount]

as a machinist this is painful to watch 😢

[@patverum9051]

Instant dismissal if you even thought about doing this on our lathes...

[@thomaslemay8817]

It is painful to watch for Machinist, welders , mechanics and the engineer that designed it . Welding with it on an unprotected lathe was bad but the grinding process even worse. I doubt it broke when they torqued the pinion nut because they don't torque any thing. In that part of the world if it looks like it is fixed it is good enough. Lives are very cheap.

[@nimrodquimbus912]

This is probably the third time this week that he fixed it

[@danielforber4097]

Lmao you seen the crane wheel repair video brings sketchy to a whole new level

[@danielforber4097]

All there equipment is war ere amazing to see post war machines still spinning away

[@lion1746]

замечательный ремонт, как раз хватит съездить в магазин, за новой деталью.

[@dryndelldryn9872]

Ага, разобрать машину, починить деталь, собрать машину, съездить купить новую "Если конечно доедешь", разобрать машину, замерить деталь и собрать снова. Л... Логика.

[@user-pr6mu9qx2s]

@@dryndelldryn9872 с - сорказм)))

[@dryndelldryn9872]

@@user-pr6mu9qx2s Да.

[@panstakanski6116]

нууу... в ситуации когда на новую или хотя бы целую деталь рассчитывать не приходится.... лучше так, чем никак. Хотя конечно очевидно, что на долгую и надёжную работу рассчитывать не приходится. В лучшем случае потихоньку домой доехать.

[@lion1746]

@@panstakanski6116 ну так они не в джунглях амазонки живут, я много видел в их видосах новых запчастей, я просто не понимаю смысла платить за работу, которая по сути халтура🤷‍♂️🤷‍♂️🤷‍♂️.

[@wildness01]

Man where to start, first of center up you're tail stock 5:22 second, don't weld on your cutting lathe, you'll destroy the ways. Third, if you are going to ignore 2 then cover the ways and spin the part as slow as the lathe will turn as you weld it, do a continuous weld bead not a bunch of tiny tacks. Fourth don't grind at the lathe, again grinding dust= abrasive=destroyed ways&wiped out bearings

[@paulwhitehouse3690]

absolutely my thoughts, a nightmare! poor guy who had to pay for this fix!

[@calthorp]

Yes all that, Then the pinion broke again on the first hill.

[@beyondmiddleagedman7240]

Look how much the tool post shakes. High accuracy built in!

[@calthorp]

@@beyondmiddleagedman7240 The headstock will get like that after all the welding arcing out the bearings

[@DerwoodBones]

Not to mention how dull and worn those bits are.

[@Poklonov]

С такими скиллами можно электродами новую деталь сварить )

[@Im_The_Slep]

As bad as this probably is, still have to respect the time and effort these mechanics put into repairs. It’s definitely not the right way. But probably on that side of the world it’s *the* option they have to take.

[@wilsonrawlin8547]

True. They make do with what they have.

[@toxichank6960]

That attempt at center drilling was fantastic. Like how the drill sprung to one side.

[@toulee8051]

BRUTE FORCE

[@vtwinbuilder3129]

Yeah all these guys are hacks but it’s fun to watch.

[@jacobclark89]

Needs short drill bit and drill center. But I guess he got the job done. I would never done that with out covering up the lathe !

[@jacobclark89]

@ICE STATION ZEBRA ASSOCIATES l don't see any porosity in the weld. I think if he used the correct rod there is a good chance it will hold . I not see what you see . It's beveled correctly to my knowledge and mutipass welding what's not to like ? I'm not sure how the heat will affect the temper . I would love to know how long the repair lasted .

[@RGIIIBOXING]

@ICE STATION ZEBRA ASSOCIATES I HAVE ALWAYS PUT MY GRINDER IN A BRACE" AND GUIDE IT WITH A HANDLE...IT JUST NEEDS TO FOLLOW THE GROVES THE BLADE IS ALREADY THIN ENOUGH..THE FRONT PART IS STILL DOING ALL THE WORK..HE JUST NEED TO PUT THEM BACK TOGETHER"

[@stewartthompson5039]

I love these educational video's, nearly fifty years as a Mechanical Engineer and I can still learn new processes - makes you feel good to be alive 😁

[@bebo5558]

That pinion probably broke again, when they TRIED to torque down the pinion nut, with the weld splatter in the threads!

[@adrianoakes152]

I love the precision measuring for the exact length to within a thou with the steel rule!

[@froller]

3:17 Look at the amazing rigidity of the lathe. It looks it have incredible precision of at least ±1 mm or even more. The machine matches the technology perfectly.

[@79chop95]

That lathe It was flopping around the a wounded duck !

[@wilsonrawlin8547]

You have to be joking around. The tool post and cross slide were moving all over the place.

[@wilsonrawlin8547]

@@79chop95 Big time! Slop city. Lucky if you can get +/- .0625

[@froller]

@@wilsonrawlin8547 obviously I am. ;)

[@wilsonrawlin8547]

@@froller 😁

[@dmitriybelousov7246]

У них там в индии какие-то волшебные электроды видимо - можно варить любой металл

[@user-ij3sd3qm3g]

Видимо их цивилизация ушла далеко в перед от нашей 😄,хочу такие электроды тож себе.

[@user-kl2qh9kb8i]

Это не Индия - это Пакистан!

[@user-ir4yf8ci8e]

@@user-kl2qh9kb8i они и индийцы такие же

[@ismaelfranciscoalmeida6803]

@@user-ij3sd3qm3g 🤣🤣🤣👍👍 é do mesmo material da varinha do Harry Potter

[@ismaelfranciscoalmeida6803]

@@user-kl2qh9kb8i pior ainda o serviço é mais porco ainda

[@olegkurizin4942]

Жалко потраченное время и электроды,этот вал всё равно скрутит

[@user-bi2jg8hl5s]

Однозначно !

[@user-zd5ze8ur2b]

Не первый раз наверно этот вал приносят :-)

[@seregaputin3851]

Выжить любой ценой

[@user-hi6dk1ux7u]

Я думал это у нас залипушники

[@igorsh5611]

@@user-zd5ze8ur2b и єтот и такие

[@chrisd-gd6no]

wow, alot of harsh comments on here. 30 yr wandering Millwright here. These guys, and alot of the third world are often very fast and seriously skilled, they have very little in the way of tools and equipment but they're not fools. This shaft may be being used in a completely different application. I've seen lots of very craftily-built equipment, particularly in poorer countries, for all sorts of purposes. Machines built from old salvaged transmissions, axles, diff's.....in fact they may be fixing it after its been scrapped for exactly the reasons you all point out below! I doubt very much these guys would waste their time and precious resources if they thought it was doomed to fail....this is not their first rodeo! I've got alot of respect for these guys, and in general "Bush Mechanics" everywhere!!

[@abdelilahtamim7456]

بحكم تجربة اكثر من ٣٣ سنة في هذا الميدان لن يقاوم و سوف ينكسر بسهولة

[@user-fb1fj1jy8s]

Полностью согласен с вами!

[@blahbaconblah]

"This repair will have you back off the road in no time!"

[@wdsracer]

The pinion yoke runout created by this repair will take out the outer pinion bearing unless the spline breaks first.

[@jimandskittum]

I don't think runout will be a problem. The taper that squares the yoke up was on the "good" side. As far as the splines go, they were already toast so it doesn't hurt to try. I repaired a blow out in between cylinders on an engine block of a turbo car with a nickel rod, a 4 1/2" grinder and a utility blade as a straight edge while it was still in the car. People were protesting so loudly that you would have thought I was killing puppies. It worked out great. You roll the dice and sometimes you hit your number.

[@ProleDaddy]

@@jimandskittum I'd expect that block sees a lot less stress than that pinion gear does.

[@jimandskittum]

@@ProleDaddy Undoubtedly. I was pointing out that you don't know if you don't try.

[@demon.kid7773]

Jaaaaaaaa.this is Craisy.I never see something like this.

[@jhart7304]

Job security, ya hater! 😂🍻

[@luiztopete5494]

Esa parte va durar mientras no la instalen ese trabajo es perdida de tiempo

[@robotmaew]

3:15 the lathe machine asking for your mercy

[@kukipett]

That poor lathe really need some attention, my god i never saw a tool holder vibrating so much !

[@arturodelagarza9028]

AND YET, THEY'LL GET IT TO WORK FOR A WHILE. I REALLY ENJOY SEEING THEM.

[@franksmith6683]

I'd love to see a follow up on how long this lasted... Maybe the driver just needed to get back home to a proper spare part, like the captain that flew a 747 from the USA back to Heathrow UK with a blown engine because the US workshops wanted too much to replace it. A bit sketchy setting off on 3 engines across the Atlantic on purpose, the busted Rolls Royce engine was testing how long an engine would last on the 747 before failure, more than 36,000 hours without overhaul which is quite impressive. I've welded a few forged steel parts by preheating and laying down some root welds with a domestic 120amp MIG and they're still working 25 years later! I once did a temporary fix on a diesel injection pump piston by gluing with JB Weld, the guide block back onto it, while I waited for a new one. That was in 1992 and it's still working, god only knows how as it hammers up and down and gets quite hot in service, which I would have thought would melt the glue. Sometimes rough repairs can work, other times not!

[@gsoupy1]

In America, this is called "Bring your kid to work day". But I guess necessity is the mother of invention.

[@bubiruski8067]

These guys are perfect !

[@BiitchSlapper]

When you get paid in Humus and Dung Beetles, you learn to cut corners.

[@adamleis83]

Hahahaha! That was looowww. Almost lower than the amount of torque that pinion is going to endure before it breaks again.

[@UnacceptableViews]

@@adamleis83 bazinga

[@s-jj1047]

Great .. for keeping it in the bookshelf, as support :)

[@danmyname]

When I clicked on this video, I was hoping it'd be something out of the ordinary with the strength to match. Beautiful...maybe...good enough...if you use it for the battery powered cars for kids, I reckon it'll last forever 😄

[@jefersonloose6474]

Um belo trabalho mas nao aguenta e assim que fizer força quebra novamente e um bom quebra-galho até quebrar de novo...mas como disse se nao tiver peça de reposição esse serviço ajuda ...mas vai quebrar novamente!!! Fato!

[@boris2342]

not a drop of cutting oil in the whole shop..... wonder how long these tools last

[@sergey6449]

Ещё немного, и в космос полетят! Такие технологии , нет слов!

[@user-ir4yf8ci8e]

да какой там, они ж только вернулись))

[@user-pr4ld1gy1l]

На сварке полетят... Варят все...

[@DedDionis]

Как бы уже летают)

[@roberthall9483]

I'm calling it,that lathe is worn,I think you could measure the life expectancy of that repair in feet and inches.

[@sethnonya8566]

I'm from United states I'm a diesel mechanic I support this kind of work reason being right now with world problems many many truck parts are unavailable out of stock discontinued or other problems. As Americans we are very spoiled either having plenty of money to buy parts new some others cannot do or the ability to get or find new parts but now that is becoming hard to do I hope the repairs they do like this at least gets them few more loads

[@beyondmiddleagedman7240]

No stress risers in that "repair". And excellent heat treatment after the "repair". I'm beginning to think these videos are just an elaborate joke being pulled on the rest of the world.

[@petermoto409]

Yet look at all the fools praising them for being AMAZING.

[@jacobclark89]

I have the same doubt as you . Maybe the truck will run fine until it goes up a hill ? If I was stranded and there was no other option I would try this , If it breaks it might take the driveshaft with it ! I would like to know if the repair is still in service ?

[@wolfeman2120]

The method of welding it back together can work. The problem is you need much different welding techniques and specific materials. Their equipment was really in poor condition and they didn't weld it properly. Then he just fucked the piece with the grinder. Should have been on a mill for that. pinions are very important and can't have any play in them. He'd be lucky if he made it a mile with that in his truck.

[@billsmith7254]

And of course we know what happens when you weld previously heat treated steel, yes it will crack across the weld. Dodgy Bros. at work.

[@MarinTheFirestarter]

Would it be better of the heat treated it after the weld?

[@nimrodquimbus912]

It's been repaired 3 times this week

[@neicarlosleal6945]

Parabéns é muito impressionante assistir os vídeos de vocês é um verdadeiro aprendizado.Parabéns Brasil

[@Sodapoparcani]

You have to work with what you have! We can criticize the process and we will all be spot on based on our experience but if all we had were those same exact tools you cant lie when I say we would do the same. Granted we might have maybe drilled and tapped both sides and cut a bolt and use as all thread to join the two and then weld but regardless we would still figured out some way to get'er done with what we have! If I didn't have any experience id be in awe but worst case scenario I would have enjoyed being a part of that process to help the situation.

[@doughawley8101]

This ‘repair’ is nothing but garbage. Weld will not hold that together long. Why do you think it broke in the first place? All the heat treating will be gone. Why didnt the cheap bastards just get another gear set?

[@doughawley8101]

By the way, I’ve been in the business of repairing machines for over 40 years.

[@carlstrohm3785]

@@doughawley8101 cheap? Or broke? Or temp till part comes? Or maybe parts are hard to come by? Who knows. Our way of life and theirs is NOT the same. I've cringed at every one of these videos I've seen. We know it won't last. But if you had nothing in the world but a worn out lathe and a stick welder, and had to deliver some product to put food on the table in an overpopulated, poor country, and that truck was your lifeblood, what would you do? It's ugly and dirty and out of spec and out of temper, but if it feeds his family, he doesn't care. Thank you God for America and our lives of privilege. And good parts 😉 And just FYI, I'm a disabled American veteran. I'm not picking, poking, or trying to start anything with anyone. I'm just saying try to look through a different lense. I'm sure they would prefer to go to a reputable shop, install new parts and have a warranty. More proof that we are the lucky ones and should be grateful for everything we have. I hope everyone that reads my comment is in good health and has a wonderful day!

[@thomaskulpmann1715]

Nicely done... predetermined breaking point. But it is not fair to judge from our part of the world. They probably have to do it more often for lack of spare parts (and money). I would also be interested to know how long it lasts.

[@chorleycake7942]

Leaning over a spinning lathe chuck wearing loose clothing is a good way to become maimed or dead. This video is an example of how not to do this job. Fitting a new or second hand part is the way to go.

[@bryancondrey6457]

No OSHA, no problem. There are 100 or more waiting for his demise to give it a try. Then they will migrate here selling themselves as highly skill machinists willing to work for one-tenth of what American, well trained machinists command in compensation. Sadly, shops will hire them and risk it until the first customer service incident. The shop owner will pocket the difference, and change the name of the company and strike out again. Isn't globalism grand? Sadly some of these people have the ego to say they are better at machining when they cannot even understand what heat does to metal and why heat treating is required. Get used to this solution because in today's world, reputable manufacturing has fallen of (thanks bean counters) and replaced with just in time mass production as cheap as possible.

[@pawemus3990]

When they will start TIG welding on those repairs. There is so much integration of deposits in this weld that may survive going out from the parking area. And how expensive are center drills?

[@makun16]

That wasn't anything close to tig welding. They where stick welding which dumped a ton of heat onto the part. It will snap off again in the same place.

[@pmae9010]

I love the thngs that can be repaired when yu need to, in America we would through that shaft away, this is cool, thank you!

[@jarmstrong2843]

Given what the machinist had to work with and perhaps unavailability of finding a new part, it looks like he did a pretty good job repairing the pinion. However, the proof will be in the pudding on how long it lasts and whether there are some alignment issues that break the part again.

[@robc3056]

Nah bodged like all of it

[@jarmstrong2843]

@@robc3056 Probably. But, you work with what you have.

[@Broyler_747]

Я так понимаю этот токарь не слышал про стружкоотводящую конавку и подбор оборотов. Но как он сверлил я был в шоке.

[@rubinroterstern]

Обороты на металле - огонь, резцы либо тупые, либо из мягкого железа, но болгарка вообще добила, хотя если посмотреть на его мастерскую, за неимением инструмента вполне сойдёт и болгарка. Токарю не хватает знаний металлообработки и инструмента, но он молодец.

[@user-ek8el5jp2c]

у них и изоленты нет, что бы намотать на резьбу, видимо - да расстроили меня ребята

[@zmagarbel]

@@rubinroterstern молодец в чем? Эта деталь работать не будет.

[@rubinroterstern]

@@zmagarbel что он хотя бы попытался что-то сделать без знаний и инструмента, потому молодец. В будущем или поднимет качество, или уйдет из профессии.

[@zmagarbel]

@@rubinroterstern чтобы поднять качество - нужны инструменты, а для этого - инвестиции. С такой работой он нихрена не заработает.

[@BigPinkBootyDaddy]

one thing for sure, a metal lathe like that can build a lot of wonderful gear. thanks for the video

[@jacobclark89]

I'm very interested to know how long the repair has lasted . And what rod was used. I wonder how the heat affected the tempering ? And was it induction hardened ?

[@NordenEngineering]

Lasts longer than having no pinion gear

[@MrHitchikerOz]

I'd give it 10 turns of the back wheels.

[@jacobclark89]

@@MrHitchikerOz then in your opinion it's not even good enough for a emergency repair . I've welded drive shafts that worked great and had no issues , but it's not really comparing apples for apples .

[@micofam5217]

They offer 30 30 warranty .. 30 seconds or 30 feet

[@patverum9051]

Hardening and tempering are inventions of the devil and should be avoided at all cost....

[@wilsonrawlin8547]

Curious to know what kind of vehicle or machine the pinion went to and if this repair held up. Making do with what you have and getting the job done.

[@user-nz9yq3qm8d]

Интересно а лопасти турбины самолета он тоже сможет приварить

[@xiong2moua]

Welding on the lathe will weld the bearings on the lathe. I had a farmer welding parts on his tractor out in the field and found out later he had bearings welded to each other.

[@aleksandrrr]

this only happens if the current passes trough the bearings, if you put the clamp on the same side as you are welding this is not a problem

[@SubieRow]

That's funny... That machine is probably older than you and me... Probably not a day that goes by that they aren't welding on it...

[@sawmill9392]

Well done repair, thanks for sharing.

[@JamesJones-zg4bv]

I guess you work with what you've got. I would lose my job if even suggested a repair like this.

[@jacobclark89]

As other viewers mentioned be very careful you're clothing doesn't get caught up in the machinery . That's a major cause for industrial accidents .

[@Dogleg1957]

so what happens to machinist that are careless.... they don't make it

[@jacobclark89]

@@Dogleg1957 maybe if it is a very large lathe .

[@svarogua9]

Коммент 100. Интересно было по какой технологии будут ремонтировать. Центровка годная, а сварка любительская. Лучшеб было шлак стачивать, поры могли остаться, хотя и так все будет зависеть от нагрузки, ведь и плицы уже потеряли прочность. Кароч. халтура.

[@Billys110]

Точно! И сломается рядом со швом при первой же серьёзной нагрузке. По-уму, надо было деталь отжечь, выполнить ремонтные работы, снова отжечь - дабы снять напряжения, полученные при сварке, а потом закалить ТВЧ. Но это по уму, а тут - маємо те, шо маємо.

[@anestalbi3955]

oui vous raison .c'est du bricolage .

[@jacobclark89]

Yes , grind but maybe not much slag from that type of rod .

[@user-yp8iv6fy2r]

@@Billys110 цена вопроса. Возможно ждут новую деталь то на месяц пока згадиться и такая. Капитально востанавливать смысла нету. Поэтому и не заморачиваются. Человек сделал к примеру на этот день себе выходной🙂, а два выходных наверно для них кошмар...

[@user-ir4yf8ci8e]

@@Billys110 о чем ты говоришь, они отливки чугунные льют, и босиком там лазают))

[@MrMaxeemum]

I would say at maximum it has 10% of its original strength getting less and less as used due to runout. If the truck was emptied and only required it to get back to base it may work if driven gently. When you are stuck in the middle of nowhere then something is better than nothing.

[@shirothehero0609]

That and the instant annealing from the welding. Any hardening that spline or gear had is toast.

[@cat637d]

The entire country is nowhere!

[@MrMaxeemum]

@@cat637d That's a bit unfair, These guys did good work with what they had and there are places that can easily beat China for quality.

[@cat637d]

@@MrMaxeemum Nowhere did I insult those fellows work, they are in a Country that has very little concern for the individual. My statement was concerning their government, please don't try to read between the lines.

[@lukakarson2075]

У них свой мир - Нирваны !

[@onetech3984]

nice sandals bro!

[@tomvogt5988]

You know these guys are doing this video just for the clicks. As soon as they were done filming, they threw the part away.

[@RJ-xv1nh]

Or if it lasts just long enough to sell the vehicle

[@heoryguban6302]

HAhAha😂😂😂

[@alexduke5402]

Yeah this is BS there's 3 possibilities here either they are really, really stupid. They are getting ready to fk someone selling the truck. Or this is just for the video.

[@alexduke5402]

I think the problem is their steel. You see how easy that drill bit went in there? Have you ever tried to drill a pinion shaft? It doesn't happen like that.

[@jacobclark89]

@@alexduke5402 did you see how hot the metal was when machining ? Did you hear the sound it was making ? It's got some hardness to it.

[@toro64xxx]

By the way you truly master Jawa, very fluid.

[@weldslikebutterfabrication483]

You don't repair anymore, you throw away and get a new one it broke for a reason

[@antonikalinowski7725]

mój pies jak nie ma co robić to jaja liże . gwarancja do bramy

[@jesusmanzano451]

You should never repair one of these, they are made of high carbon steel

[@ruenjou]

They had welded wheel axle shafts (even higher torsion loads) before so this repair is no big deal :) In the next video, they will weld a broken conrod...

[@rehanullahmarwat373]

I am fm pakistan , in fact they do weld conrods

[@jacobclark89]

Do you if the repair has lasted ? I'm wondering about the heat from welding taking the tempering out .

[@davidelliott5843]

@@jacobclark89 Who knows, maybe the original failure happened because the part was too brittle. If it runs true the repair might be stronger - IF it runs true.

[@ma61king]

Who doesn't love a dry high speed and feed interrupted cut into case hardened steel with no coolant...

[@user-mk5xq8dg9z]

Вы замечательные технари! Только в вашей стране такое возможно. У нас бы в России этот вал выбросили и всё). А вы Ребят чудесны👍

[@user-bi2jg8hl5s]

Выбросили бы и набухались , а утром пошли бы другой искать .

[@anestalbi3955]

oui vous avez raison .même chez nous en Algerie on le jette.

[@user-ir4yf8ci8e]

У нас бы в России этот вал, сдали бы в приемку))

[@user-mk5xq8dg9z]

@@user-ir4yf8ci8e это одно и тоже, но не тоже самое).

[@user-xx7sb8yu3w]

Замечательные технари 🤣🤣🤣 А где ты технарей увидел? Обычные халтурщики они и точка! Если бы ты хоть чуточку в своей жизни изучали бы сопрамат и материаловедение,то вы так не писали!

[@user-mh1rx7uk5y]

я на митсубиси галант привод длинный типу сварил из двух частей (раскололся при дтп), доехать чисто, но трубку сверху одел для крепости и проварил еще , думал хватит доехать, а он 3 года так проездил мотор 2 литра мощный он наваливал говорит, я прям удивился что он столько проездил)))))))))

[@mikhailhmelevski7419]

Спасибо вам за душевные коменты 😁

[@supersilve]

The end result is the shaft out of center and the weld will not last. the shaft will probably break again. Seriously a beautiful Job?

[@timothygeiger8271]

Its not a matter of "probably", its definitely going to break the first time any torque is applied to the driveline. They spent alot of time repairing a paper weight.i certainly wouldn't use that pinion in anything i own.

[@jacobclark89]

Most of the comments seem to think that the weld won't hold , but in reality not all of the people who commented are welders and out of the ones that are, probably only a small percentage are expert at welding cast , so I feel that the majority aren't quilafied to make the assessment in the first place , I do see a trail of mistakes made while making the repair that makes me loose trust , but I must give respect for complexity of the repair . Im sure they make many repairs that have been a great help to society and deserve respect for that . When it comes to welding, their are many different processes and disciplines to master . Boilmakers , jewelery welders ,under water welders ECT.

[@ZahidKhan-tj8ty]

Amazing.

[@juliomoisesgallegospreciad178]

EXCELENTE RECUPERACION DEL PIÑON. UN SALUDO A TODOS AQUELLOS QUE SE DEDICAN A ESTA NOBLE LABOR. ATTE. MOY.

[@michaeltaunou9281]

Good job. With this ,make money then buy brand new one.👍

[@Str8UPdyeabolick]

I could have done the same with JB weld, it might last longer too.

[@un-factory]

Good idea

[@mrgreynomainnogain2068]

what welding rod you use?

[@ArmanArman-dr6zg]

Just enjoy the proces, i like to say" what a great proces

[@adventureconstruction2668]

Good job 👍

[@mostlymotorcycles.]

I would imagine if it broke 10 metres down the road they would be out of business pretty quickly. These kind of repair shops would rely on word of mouth and quality of repair. But I do agree with all the comments on hardness and toughness of the final repair. Without a doubt the strength is dramatically compromised. They probably advise to replace with a new part ASAP.

[@bogged2theeyeballs695]

I wish they had shown the installation of the repaired part. Watching them set the pinion preload and checking the mating of the gears to the crown wheel would have been entertaining.

[@TheMrCroup]

I seriously doubt they go through that much trouble, the truck that is for is not meant to last due to the nature of the roads they tend to drive on. Wooden body on a cheap metal frame.

[@thomasschleis2545]

Who needs a mill, when you've got a good grinder. Jeez!

[@FB-jg2xq]

that welding it's hard enough like to use spitt . good job.

[@samhendrix378]

I wonder if it will hold up or just break again when in use, But good idea.

[@SukhdevSingh-ib9dk]

Witch use type s of welding stick please reply

[@Ahmed-mo1jh]

فینشنگ نہیں آئی اتنی محنت کی اس سے اچھا نیا لے لو پورا لوڈ ہوتا ہے بھائی زیادہ نہیں چلے گا۔

[@williamgrissom9022]

Probably doesn't matter if the splined shaft winds up slightly shorter since they probably use shims to fit the gears together. Main thing is to maintain the two welded parts are parallel. I suggest safety glasses, even though nature gave us a spare eye. Interesting how they make a grinder work since presumably don't have a horizontal milling machine and correct cutting tool for the splines. Cost of repair $15? Biggest concern is if this is the input pinion on the differential of a semi-truck, as they must use engine-braking to control downhill speed. If it snaps, the truck could runaway on a steep road.

[@andrewrobinson2869]

I cannot see that being strong ENOUGH

[@ignacioveramendi6942]

Electrodos 600, se usan en ARGENTINA

[@texhow1]

Which type of steel rods would be needed.

[@dan-o9746]

Ray Charles made better welds. Your tail stock is off so bad, you need curved drill bits!

[@jacobclark89]

🤣😂 I give it a 60/40 to break in the first month. And a 40% it will take out the drive shaft when it breaks.

[@williamphillips4344]

I wonder how the heat from the peck welds is going to help the temper of the metal? Maybe a little brittle .

[@mashkhurraimov2494]

And how long this thing will work further?

[@roberthall9483]

You just know that when a heavy component was dropped on the floor,nobody ever said,thank God I was wearing sandals.

[@nimrodquimbus912]

Those are Chinese safety shoes

[@717Fang]

its a good video to learn how repair will be not done.

[@abderrahimhaddanitankioupr9367]

THANKIOU

[@jimandskittum]

Stop, drop a gear and pop the clutch Driveline parts can't cost too much! Seriously though, that drill bit deflection at around 5:23 : p

[@seancollins9745]

USD for a ring and pinion set for a medium duty isuzu or nissan, EASILY $1400 or more

[@nicnic1434]

Спасибо за видеоролик

[@SharpByCoop]

The most 'Beautiful Way' about this video is the laughs I'm getting reading the comments.

[@Klyuch_Na_13]

Ребята стали не ремонтировать,а снимать,за это видимо больше платят.

[@fryderyknowak1536]

I admire the skills of these people,what an ingenuity

[@reginaldorocha8272]

O trabalho correto neste caso é fazer um furo em cada peça no torno e bem centrado, colocar um pino bem justo e depois soldar

[@user-hi6dk1ux7u]

Да ты прав.

[@user-fb1fj1jy8s]

@@user-hi6dk1ux7u нет, не прав! Эта хрень что они свояли, тут же лопнет при первой нагрузке. Такие детали ремонту не подлежат!

[@user-hi6dk1ux7u]

@@user-fb1fj1jy8s ты прав

[@johnfragkos2242]

what modul have the griding wheel omg that was unaspekable 4 meters only to break again

[@williepelzer384]

If it broke the first time, what makes you think it will last now?