How to Replace A Honda CR-V U-Joint

[@DIYApprentice]

I removed the driveshaft from my 1997 CR-V about a year ago because of rusting u-joints; I finally got around to replacing the u-joints. I had to grind down a second plug I bought for my ball joint press so I could press out the old u-joints and press in the new joints. I used a Drexel to smooth the holes then I applied some bearing grease to help the caps slide in easier. C-shaped clips were tapped into place to secure the u-joints.

[@DebtFreeCars]

You purchased the wrong type of U-joint. You can get U-joints that have clips on the interior side of the yoke. Just grind the stake points smooth and slide the U-joint cups in and clip them in.

[@tamiibrock6176]

I really appreciate for your time. I have Honda pilot 2011. I was trying to change but the same thing happened to me. There is no way I can do it except buying new one.

[@EddieCarrara1]

Hi Tami, some trollers say it can be done, so I gave it my best shot. Unless you replace the yolk on the propeller shaft it would be impossible. Sure, I could jam it in there then stake it, but I really didn't want my u-joint exploding while my kid was driving on the highway. Thanks for your feedback 😊

[@jeffwalker4929]

staked are replaceable - I clean out the yokes and press on the new joint, then I use washers that are the same size as the bearing cap, set the preload on the bearings, and set the washer on top the cap, and give it 4 small welds with the MIG. Works great! And saves the drive shaft!

[@Goneloco77]

Great video that's why a cant find the u joint in the auto part stores

[@meelays]

While disappoint to have to replace whole thing, thank you for the video because I least I learned that you can't just replace the u joint.

[@knockdown7getup8osda28]

Hi Eddie, Great channel! Thanks for all the good information you provide.I have a 2006 Gen 2 V, and have a few questions. How is that Dorman drive shaft holding up? Are the U joints replaceable on the Dorman drive shaft?

[@EddieCarrara1]

Hey thanks KD7 I appreciate the feedback 😊. The U-joints held up for for 45k miles with no issues, then we upgraded that CR-V. The U-joints were replaceable on the Dorman shaft, but I highly recommend you inquire about that information on the one you're buying because I'm not sure if all of them are like mine. Keep me posted on what you find out, thanks.

[@knockdown7getup8osda28]

@@EddieCarrara1 OK will do! I will be getting a drive shaft for a 2006 Gen 2. So I'll make sure the one I get has replaceable U's.Thanks for the quick reply.

[@EddieCarrara1]

@@knockdown7getup8osda28 Let me know how you make out. 👍

[@MultiSskill]

It just happened to me, why is this happening? my axle crossheads were new

[@majorame]

Hi...other than these ones on the propeller , are there other u joints on the CRV RD1?

[@EddieCarrara1]

Hi Aran, one at the transmission and one at the differential, let me know if I can answer any other questions for you 👍

[@netocame]

same thing happen to my crv, , i got a pair of dorman 933 045 u joints and solve the problem with welding , enough not to damage the u joints......until now they are working very well

[@wtfisthis9192]

How does aftermarket vs the honda OEM shaft compare? Does it matter which one I buy?

[@EddieCarrara1]

If your vehicle is older I recommend an aftermarket driveshaft like Dorman. Honda driveshafts are 3 time the price.

[@wtfisthis9192]

@@EddieCarrara1 Thanks for the reply. I cannot find it for $300ish I am seeing 800+ any suggestions? I live in Canada.

[@EddieCarrara1]

@@wtfisthis9192 The price will depend on the year make and model www.amazon.com/Dorman-936-001-Driveshaft-Honda-CRV/dp/B009PJKA5M/ref=sr_1_fkmrnull_1?keywords=dorman+driveshaft+2003+honda+crv&qid=1556073232&replacementKeywords=dorman+driveshaft&s=gateway&sr=8-1-fkmrnull&vehicle=2003-59-754------------&vehicleName=2003+Honda+CR-V

[@rikdeschain2476]

hey having trouble getting my bracket on the u joints to match up any helpful hints

[@EddieCarrara1]

+Rik DesChain Not sure what you mean by Bracket? I don't know of anyone who has had success replacing any u-joints on a CR-V yet.

[@JoseRodriguez-sd2rj]

+Eddie Carrara I replaced them

[@leojeq2004]

Thank you for the explanation greetins from Costa Rica !

[@EddieCarrara1]

Hello Leonardo, you're welcome. I have had some KZbinrs tell me they are replaceable but in my experiment and experience, the stock U-Joints are not replaceable.

[@skyscraper37]

Rockford drive line. Get new joints...can be done yourself...get a grinder clean out holes nada boom nada bing

[@jestep9]

Thanks for the info. Saved me a lot of time.

[@EddieCarrara1]

Hey Jestep9, Some people will tell you that they have changed them with success but I didn't find that possible lol.

[@tracygibson7702]

God love it.. How much did you make to say you have to get a complete driveline. You can get internal locking u joint and you can replace it with a Rockford 430-9a. Or send it to me. I'll replace and return it less than a new driveline. Message me for details

[@EddieCarrara1]

I didn't get paid Tracy, I was just sharing my experience. I also was saving my viewers time and frustration because if the average DIY mechanic spends a couple hours replacing the joint and $60 on parts, then it blows up driving 60 mph down the highway because the yoke was worn they wouldn't be very happy. Hopefully someone contacts you to replace one for them and you can make a video of how it's done so you can help out other viewers. Thanks for sharing 🍻

[@OfficialNewsToday]

I just broke off completely, very helpful info

[@EddieCarrara1]

+5ok99 , I was pumped to replace the u-joints, I bought both front and rear joints, then found out it can't be done, lol.

[@JoseRodriguez-sd2rj]

where can I post pictures

[@42santana]

what were the symptoms that the drive shaft u-joint was bad

[@DIYApprentice]

42santana My CR-V has a bad vibration when accelerating.

[@SevenDoubleO-j2r]

Sorry brother but the clips go in the inside of the joints not in the bracket that holds it with aftermarket joints was very fixable and u could have done very quickly

[@EddieCarrara1]

Where were you 10 years ago?

[@ezbgame2956]

I replaced my driveshaft and i hear i grind noise still can some one help

[@EddieCarrara1]

Do you know if the noise is coming from the driveshaft or maybe somewhere else? Brakes maybe?

[@skyscraper37]

Besides you did the hard part getting the old ones out

[@duncanwalker7380]

Got the same problem...

[@EddieCarrara1]

Hey Duncan, Some people say they can be replaced, I keep asking for videos from these people and haven't seen one yet.

[@irustach8902]

thx pozdrowienia z Polski

[@EddieCarrara1]

You're welcome Iru Stach.

[@reginaldhunt3771]

I'll show you how to replace the you joint because nobody tells me I can't do something!😉

[@LuckyTown77]

Replaced many in my career

[@delsen.oboisen2245]

Good preso.

[@EddieCarrara1]

Thanks Delsen

[@OhioOwns]

so in other words, Honda wants you to spend nearly 300 to 500 dollars instead of just paying 25 bucks to replace the part? what the hell

[@DIYApprentice]

Ohio Against The World You can buy aftermarket u-joints that will work for the CR-V. You need a press or a large punch to get them out and to install the new u-joints.

[@OhioOwns]

***** can definitely manage that. appreciated, because it's really about to go, I can tell.

[@OhioOwns]

bad rattling going down the highway. thought it was out-of-line at first, but it has to be the u-joints.

[@DIYApprentice]

Ohio Against The World I used a ball joint press with a plug tip I shaved to fit on top of the caps and through the ear holes - worked well and is potentially less damaging then using a punch. You can remove the driveshaft and just run in front-wheel drive "mode" if it gets really bad. Also, the service manual recommends marking the orientation of the shaft to the transfer assembly flanges before removing the driveshaft so it's reinstalled in the same position.

[@OhioOwns]

***** that's goddamn brilliant, really. i'm going to do it the same exact way if it's a tried & true method, because i'm def not paying a garage 200 to put on a 25 dollar part. the rubber bearings are wearing off insanely fast too, don't know if that's because of the movement of the tire from the u-joint going out or what but I gotta grab some of those while i'm at it. thanks, man, it's really appreciated.

[@JoseRodriguez-sd2rj]

me I replaced it