How To Replace A Motorcycle Clutch - Honda XL600r RFVC XL XR

[@Rumbo64]

Hello, thank you very much for your great video. 4 months ago I bought an XL600R from 1983 and am currently repairing it. The video comes at the right moment. Very well recorded and really well explained. 👍

[@joecaraco7503]

That's more involved than my old 84 Yamaha Venture. I found that I didn't need to drain the oil if I placed the bike on the side stand and at that angle it was easier to work on the clutch replacement. Chris, you have the most entertaining site on KZbin. My wife and I can watch you and Jen for hours. Joe and Ginny

[@ghouliesgarage3922]

Not thqt i coild rebuild one now ( health problems) but actually from watching this video this seems relatively easy .thanks Chris ! Awesome Bike

[@naturalmedic]

I need to tear into my xr600r. Thank you for being thorough and having great camera shots.

[@1skinnypuppy]

I certainly wish I could press the like button more than once! Thank you very much!

[@NoNonsenseKnowHow]

No problem! Glad it was helpful

[@charlesbrown2451]

Great step by step narration!

[@Fernando1115]

Very helpful video i did the same work on my nx650 and now clutch is like new 😀 thank You and greetings from Poland!

[@NoNonsenseKnowHow]

Happy to hear you found the video helpful. Thanks and greetings!

[@osalcedoucmsae]

That exhaust looks amazing!🥵

[@NoNonsenseKnowHow]

Yeah the XR's only header is pretty sweet! I actually did a video about polishing that super trap too lol. I kind of did a half crumb job on it but it shines okay

[@AR-798]

Nice camera work and very informative thanks.

[@brianreid3494]

You are awesome man wish you could have saved my 1974 Suzuki. No one in Ohio would replace my piston ring.

[@NoNonsenseKnowHow]

On Amazon: *CLUTCH HOLDING TOOL: amzn.to/2LqgyTc *N52 MAGNETS: amzn.to/3hKxeRy *XL600R CLUTCH KIT: amzn.to/395B4km *12" FLAT FILE: amzn.to/3pVE09M *TACKFORM PHONE MOUNT: amzn.to/35cxovJ ~CLUTCH BASKET REPAIR VIDEO: kzbin.info/www/bejne/jJnQZYFme9hrjZY ~ XL600R CLUTCH ASMR VIDEO: kzbin.info/www/bejne/qavKeIiXiNOqf8U

[@joemalcom7029]

My 86 XR 600 sounds just like that XL. Same startup whine and all. Thanks!

[@NoNonsenseKnowHow]

No problem! Good luck getting it taken care of

[@anthonywelliver9050]

I have an 87 xl. That happened to mine when i used 20 50 oil. I changed to lighter weight oil and no more rattle on startup. Mabye the oil is too thick when cold.

[@gusgiesel]

Ahh I see this model does not have a separate clutch cover and you must remove the right side engine case cover as you have done. My XR400 has a round cover just for clutch work and people are always getting confused about the clutch cover vs the right side case cover. Thank you for the excellent video!

[@marcelortfontenelle3081]

Very good video. I own a Honda XL 600 LM 1985 made in Japan. I'm from Brazil. I'm doing the service by myself and video added good tricks to help, even I own the original shop manual. Thank you. Regards.

[@TravisMontesano]

looks like a ton of fun, now i want one!

[@NoNonsenseKnowHow]

Heck yeah man!

[@bradrussell624]

Awesome man, in-depth and detailed explanation, thanks for sharing :)

[@BB_nl]

Thanks for this great video! I noticed on my bike when I took the pressure plate off that the bearing could be taken out very easily. It seems there is no play but it is definitely not 'pressed' in like you would expect from a bearing. Maybe best that I replace this bearing?

[@jayfromtexas6718]

Talented guy!

[@kahidunn7907]

Great videos, clear, well detailed with a heap of handy tips, top stuff, cheers mate

[@jimmartin7881]

What an awesome bike, I've been looking to get another but I'm not rushing to buy. I always find that works best, I had a 400R but sold it when I had my daughter. Not sure if but I'm thinking of a Transalp or a KLR maybe, I just have to weigh my options and see what's out there. Basically I just want something for daytrips and backwoods exploration, stay safe bro!

[@NoNonsenseKnowHow]

Yeah man the xl600r's are a sweet bike! Truth is if I was going to buy something similar today I would definitely get an XR650L. But this one is very dear to me since I've had it for so many years and been through so much with it. A lot of people knock the kickstarter. I personally love it. But that's because my knee is still strong. Might not think that way a few years from now who knows. I always liked KLR's also. I used to have a 250 and a 650 also. Both great bikes. Good luck in your search.

[@jimmartin7881]

@@NoNonsenseKnowHow Kickers rule! My brother's got an FXR with a worked S&S 124, kick only! Thank goodness for compression releases, lol.

[@jasonmosher-jtm]

great job. Really great explanation

[@NoNonsenseKnowHow]

Thanks Jason

[@nomadmarko98]

Please can you do a video on how did you ungrade it to xr600r suspension

[@2wheel_right]

Put greaseat at engine side and glue the gasket at the cover part, you avoid disamble problem and need no new gasket.

[@stillshot2]

Just put Valvoline 20-50 full synthetic motorcycle oil in my xl250r, said excellent wet clutch protection on the bottle. Should I have not used full synthetic?

[@huntercobb9881]

I hope that was the shift shaft behind the clutch lol bc I can't find anything but this and its close to a xr650l motor

[@Jerboneous]

What kind of exhaust is on your bike I just bought an 1987 and the pipe on mine is super rusty. Cheers

[@danielemuraro8827]

The rattling noise that you hear at cold start is the oil filter (expecially not OEM filter). I have a question...on my 1988 NX650 dominator, I have the kickstart that sometimes disengage when loaded for the starting kick. The kickstart lever rotate free for about 1/3 of the entire run .. What I have to check? I appreciate a lot your videos they are very accurate!

[@NoNonsenseKnowHow]

Could be worn out splines or kickstarter teeth. Would need to be taken apart for inspection to verify. Should never slip

[@NoNonsenseKnowHow]

And thanks man I appreciate you checking the videos out and the feedback

[@chapinrico]

I have just finished rebuilding my 1984 XL600R. I see you have an oil temperature dipstick. Any way you can share link to buy?

[@NoNonsenseKnowHow]

I got it from xr's only.com

[@markcdeyoung3118]

I've been thinking about converting my swingarm and suspension to an XR650L I have five of these things I love riding them but they don't suck up bumps like my XR650L does 👍

[@supabry26]

Greedy bastard!

[@markcdeyoung3118]

@@supabry26 😁👍

[@BeaverSmashing]

I don't trust torque specs on clutch pressure plate bolts anymore. Different bike but spec is 78 inch lbs, bolt snapped at 32 inch lbs 🙃 I get them well and snug and call it good. Mine were aluminum bolts though.

[@DisposableBelief]

Hi! I am about to change my clutch friction plates on my 1983 model. Would the clutch friction plate part number that you used here will fit my bike? Thanks in advance.

[@MattCoda]

Thank you so much for making this video. I'm working on a kickstarter return spring problem with an 84' xr500r, and this helped a ton. I'm a rookie at working on bikes. Quick question, what kind of silicone are you using on the gasket?

[@NoNonsenseKnowHow]

No problem! Great to hear it was helpful. I really like using Permatex the right stuff. A little smear rubbed on one side goes a long way. Or a tiny bead. Be careful not to use too much though. It should just barely start squeezing out the tiniest bit when you torque the cover bolts

[@mastermoarman]

Nice video. Donyou have a video for the rear end swap? I want to do it to my 88

[@NoNonsenseKnowHow]

Thanks. I made a brief overview video on it a long while back. yea. Google NoNonsenseKnowHow Xl600r suspension. I think i touch on the rear in that?

[@pjaekdanmark5275]

Hi there, great video! Can you help with the part number of the crankshaft oil seal? Can't finde it anywhere on the RIGHT CRANKCASE COVER Part drawings. Thanks, Thue Denmark

[@iamadness69]

Hey man I noticed your clutch basket slid right off the shaft with no effort at all, mine seems stuck, I pull on it and moves maybe a 16th of an inch out then stops like its getting stuck somewhere. I know it should slide right off the guide/bushing, I really can't figure out why thats stuck and I don't wanna break something or bend the basket trying to pry it off...

[@neosandi6]

thenx man for good video

[@NoNonsenseKnowHow]

You're welcome!

[@tsauleda]

Brilliant explanation, thanks a lot! Do you have a link to buy the EBC extra strength springs? I already have new friction plates, but I guess my slippery clutch issues really come from the old springs too loosen

[@KoalaEater]

Love the channel

[@twinrideradv2473]

Miss the days of the all mighty Africa Twin xD

[@mauricioreyes6358]

Hello! I would like to ask you a question. Is the rear brake disc an adaptation, from which motorcycle is it? I would like to implement this improvement on my motorcycle. Thank you in advance!!!

[@NoNonsenseKnowHow]

Yes it's rear disc brakes from a XR650L

[@mauricioreyes6358]

Thank you!!

[@lucasking4197]

Hey man I just got the same bike like yesterday lol and was wondering where you get all your parts and if you can get part from a new one for it

[@NoNonsenseKnowHow]

Usually whoever has them cheapest on eBay or any of the OEM parts sites. I usually price check around

[@debugger1943]

hi. wanted to ask you, I have a trouble in finding where tachometr cable is being connected. I have 1983 Honda XL600R PD03. Can anybody help, please ?

[@bigrickhiggins9797]

Great vid good I nfo! went to do a clutch on my 87' xr600r and found a few metal chips on my pulse gen. Everything on that side seems good. pulled the kicker gear and it also looks good. any ideas on where those chips could have come from?? time to split the cases? both screens and filter were clean. thanks in advanced!

[@Splashfun2000]

you don't show when you put the kickstarter gear back in, do you have to rotate it to a certain point ?

[@abmivo6070]

My xr just shuts off when I try put it in 1st or 2nd they said the gear not catching neutral does it mean i got remove those plates an get new ones ?

[@maximethomas8549]

Hi where did you find the inox echapment?

[@BackcountryHonda]

When can I bring my bike over for a clutch job?

[@Mrtweet81]

Im stuck, im trying to change the clutch on my R1150GS, i have placed the plate in oil but nothing else makes any sense...

[@spikeman68]

i know this a old vid but what swing arm and wheel is on your ride? i tried a dr650 wheel(disc) and it grabs maybe a little better then the old drum..............nice ride!

[@NoNonsenseKnowHow]

It's from an XR650L. I did a short video showing some details on it a long while back. Used the XR650L front forks also

[@spikeman68]

@@NoNonsenseKnowHow thank you nono,do you feel it raises it to high?and do the rear brakes grab good?

[@NoNonsenseKnowHow]

No it feels good for me. I'm six foot three. And yeah the brakes work well

[@spikeman68]

Thanks buddy i appreciate your time,ive been thinking of the swap for a bit ,looks like its time time to go to ebay! lol thank you again and im going to look at your other vids for help!

[@jamesstackel]

hi mate, my xr600r seams to have a weird clutch issue i think, when it's cold the clutch seams to stick disengaged, i can put it in gear and roll it like i have the clutch in, which makes roll starting impossible. have you ever come across this problem?

[@jessesalcido2562]

Awesome 👌!!!!

[@TeamTheYoungandTheRestofUs]

Great vid, thanks

[@osalcedoucmsae]

Did you have to prime the oil pump or anything?

[@NoNonsenseKnowHow]

Nah you don't have to do anything like that with these

[@osalcedoucmsae]

I got a spare engine from an 86 that I’m putting into my 85 real soon so found your video just in time

[@NoNonsenseKnowHow]

Awesome!

[@ede6466]

Hello, what is the temperature of your engine when you ride ling trip off road? Thanks,

[@NoNonsenseKnowHow]

Like 250F or so

[@89HondaCR500R]

If I remember I think my comment was just for the reason your kick start wasn't returning properly. As to the click noise it could be a few things , a loose timing chain or oil pump could be slightly worn or could be wrong oil viscosity for the temperature in your area, but to be honest that sounds pretty normal for a 30-year-old bike my xl600r made the same noise as does my 2002 xr650l

[@NoNonsenseKnowHow]

Yeah basically the kickstarter gear makes a slight ratcheting noise when it's cold for about 20 seconds and then goes away. It's definitely just the cold oil. I run 10 W 40.

[@NoNonsenseKnowHow]

Either which way I appreciate you commenting that because it motivated me to pull the kickstarter gear apart and check the alignment. I was very surprised to see it was off by one spline.

[@NoNonsenseKnowHow]

I just went and looked back at the original top end noise video now. @11:23 Yeah you're right it didn't return all the way, that was actually the kick-start lever hitting my foot pedal or brake lever. I had to bring the kick start lever out a fraction of an inch on the splines and that corrected it. I thought you were referring to the clicking noise when the engine is running that I mentioned. Oops.

[@89HondaCR500R]

But looks and sounds to me to be a perfectly healthy bike for its age happy trails to you brother

[@NoNonsenseKnowHow]

@@89HondaCR500R happy trails to you too David! Thanks again

[@Hondaguy82xl]

What exhaust is that?

[@Josh-co7pz]

I snapped one of the clutch pressure plate bolts at 108inch-pounds ;(

[@NoNonsenseKnowHow]

It's really best to do them by feel from my experience. But of course that takes years of talking fasteners to be accurate with.

[@vanchua2007]

❤❤❤

[@sarelzecchin3700]

Thats why always use ghries on my gaskets then it doesnt get stuck

[@jeremyodonnell5551]

Looks like a 1985

[@NoNonsenseKnowHow]

1986

[@NoNonsenseKnowHow]

It's been painted

[@jeremyodonnell5551]

Okay got you I was going to say because I've had a 1986 and currently have a 1987 and they are both white frame red engine

[@supabry26]

Hey bud , just to let you know , your starter making that noise because its not aligned properly .

[@NoNonsenseKnowHow]

I'm guessing you didn't watch the video. Still makes that noise with the starter aligned properly. They all make that noise when it's cold and have thick oil

[@OsmanWang-ck8gj]

Au...

[@user-wk9pz1xn1o]

Это про родитель, старичок