How to Replace Front Brake Pads and Rotors 2013-2017 Honda Accord

Buy Now!
New Brake Pad & Rotor Kit from 1AAuto.com 1aau.to/ia/1ABP...
New Brake Pads from 1AAuto.com 1aau.to/ib/1ABP...
New Brake Rotor Set from 1AAuto.com 1aau.to/ia/1APB...
This video shows you how to install new, quality TRQ brake pads and rotors on your 2013-2017 Honda Accord. Brake pads wear out over time, much like tires, and need replacing, on average, every 50,000 miles, with variations depending on driving habits and environment. Brake rotors may also need to be replaced if they are warped or grooved. Often, it’s safer and more cost effective to replace pads and rotors at the same time. Squealing or grinding noises, or wheel vibration are all symptoms of worn brakes.
This repair was done on a 2013 Honda Accord EX 2.4L Sedan 4-Door FWD Automatic and the process should be similar on the following vehicles:
2013 Honda Accord
2014 Honda Accord
2015 Honda Accord
2016 Honda Accord
2017 Honda Accord
Tools you will need:
• 19mm Wrench 1aau.to/oZs/1AX...
• 14mm Socket 1aau.to/obEc/1A...
• 17mm Socket 1aau.to/obEc/1A...
• 19mm Socket
• 1/2 Inch Ratchet
• 1/4 Inch Ratchet 1aau.to/obje/1A...
• 3/8 Inch Drive Ratchet 1aau.to/obEc/1A...
• Torque Wrench 1aau.to/oaL4/1A...
• Gloves 1aau.to/oam7/1A...
• Safety Glasses
• Floor Jack 1aau.to/oabk/1A...
• Jack Stands 1aau.to/oYn/1AX...
• Wheel Chocks
• Wire Brush 1aau.to/ot6/1AX...
Subscribe: / @trq
Check out our playlist:
Honda Accord 2013-17 9th Gen: • Honda Accord 2013-17 9...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@jtprice8775]

Nice video, Clear and thank you for telling people what size socket to use for removing the bolts and the torque specs too. I would recommend using anti-seize on the rotor mounting screws. Speaking from experience, especially in the northern climates, it will make it easier to remove them next time.

[@guesttourist4472]

if u all don't know , not good at cars then maybe this video is good for u all but from year 15 n up hondas have electric calipers, he didn't mention anything about it. so make sure u all don mess it up

[@grimeball]

Curious - what did you use for the “skim coating” in the grooves on the bracket? I expected it to be grease, but you used a different bottle than you used for the caliper pins

[@eddiejauregui4519]

Sir… you added what you used besides what you used for the “Skim” lubricant. I appreciate the video greatly, it helped a lot. If only you added the “skim” lubricant. Have a good day.

[@80sbaby___baby70]

Only if every mechanic was this thorough

[@WarpigPSU]

Nicely done video.

[@clintonbubb3187]

FYI... The brake rotor screws are JIS, not Philips. If they come out easy, no issue, but if you need to use any impact tool to loosen them, a Philips head might round over the JIS screw.

[@matthewliberatore3832]

What is the two different grease used on this job ?

[@mredrvservice]

Good Job Nice review before I do it again,Always nice to check for updates

[@mikegrant5435]

Excellent video. Concise and well explained. Thank you for sharing.

[@FranciscoGarcia-hi3zx]

Wish you guys had a install video for the 10th gen

[@TRQ]

+@FranciscoGarcia-hi3zx We're always cycling through common cars. We'll add this repair to our list! 1aau.to/m/Shop-TRQ

[@tommygriffin7320]

You have the anti rattle gear wrong. Check at 8:51 the tab is pushingg against the outer plate of the pads. You didn’t install them that way.

[@IH8YAGPEEPO]

Ummm am I trippin or did you only put 2 of the 4 screws for the rotors on?