I, 3, & 5 injectors and plugs are on the firewall side. 2, 4, & 6 are on the oil cap side. Mine had a pool of oil in the intake hose. Also had a lot of oil sucked into the intake manifold. I cleaned it all out and did the PCV orifice mod. Also cleaned the throttle body. The intake put up a fight coming out due to the long bolts in the rear. It put up an even greater fight going back in. In my case I just didn't have enough clearance to replace the rear intake bolts. For those having the same problem, I highly recommend jacking the vehicle up by the front cross frame member and placing it on jack stands. Let the vehicle rest on the jack stands but keep the jack under the cross member. Remove the six cross frame bolts on the bottom ( three on each side) below the condenser. This will allow the engine to rock forward/lower. You may have to lower the jack a little but it will give extra clearance in the rear to reinsert the rear intake bolts. I also snap the same hose, Think egg shell when handling it because it will snap just that easy.
@robertrussell345 жыл бұрын
So the oil in the air intake was from a injector
@mikenordseth79813 жыл бұрын
I've ran into oil in the intakes many times!!
@vincentnavarro48164 жыл бұрын
Bro you just freaking helped me out so much!!! Up 2 in the morning looking for a video for this! Going out in 0 degrees to work on it now! Haha yes thanks!
@crxracr233 жыл бұрын
Did it fix your misfire on cylinder 3?
@TheGivebackmyworld Жыл бұрын
Thanks for the video. I intend to replace injectors someday. How are manifold intakes look so cleaned?
@matttownsend13086 жыл бұрын
Commonly there are injector wires under the power steering reservoir bracket and they rub through and ground the injector
@100fredkrueger3 жыл бұрын
Thanks for the video. My wife has an 08 enclave which has the exact same engine as your Acadia. Hers is idling really rough and I keep getting a code that says running to lean bank 2. I have replaced the spark plugs, catalytic converters, and O2 sensors so I am thanking about putting injectors in.
@zacmosley82232 жыл бұрын
Did this work?
@katiebonge28906 жыл бұрын
one issue I have is a vacuum leak on 2009 Acadia. When I spray water on the bolts that hold the intake manifold, the idle changes pretty drastically so know that is part of my vacuum leak. I noticed that the grommets are missing on the bolts, could that be the issue for the leak there? I can't located where to buy these and the advanced auto guy was at a loss as well. Maybe I"m calling it the wrong name but the black sleeve that goes over the bolt. I"m replacing #4 coil and also getting P304 code for coil and also injector may be dirty. Says possible air leak on manifold or in the EGR or PCV.
@carsonhowell24106 жыл бұрын
you can try to put a little glob of RTV black just under the head of the intake bolts. its like a "cheap fix"
@ironfistarrival2 жыл бұрын
Hello ,shouldn’t you first disconnect the Fuel pump Relay and even the battery?
@jaureguuii79392 жыл бұрын
Ey bro i had one problem with my acadia 2008 Its burning alot of crude gas and it smokes dark smoke I already change spark plugs coil pack change the map air and nothing I was thinking maybe a injector cleaner or may be a bad injector it smells like crude gas when I step on the gas all the way in dark smoke comes out of the exhaust what do you think looks like a injector its not burning gas correctly or something
@davidduke75315 жыл бұрын
Taking the fuel cap off does not release the fuel pressure at all. You have to pull the fuel pump fuse or relay, start the car, and let it run till it shuts off. That debleats the fuel pressure.
@rodneybarfield76332 жыл бұрын
i have a 2008 gmc acadia slt and i have a code po1174 on bank2 is this injector number 2 is this the one i change
@davidherman84564 жыл бұрын
Awesome video. Do you recommend replacing the high pressure intermediate fuel feed pipe?
@ariellamb90023 жыл бұрын
What are the torque specs for the intake manifold
@mikenordseth79813 жыл бұрын
If your dropping bolts u should put your oil filler cap back on...
@two2theface4082 жыл бұрын
Was nervous seeing that opened at the end....bad idea
@donthegamer16755 жыл бұрын
This was very fucking helpful thank for taking the time to do this video, you just helped me save thousands of dollars $$$
@BarkingTitty6 жыл бұрын
Did you fix your cylinder 3 misfire by replacing the injector?
@maxamasj6 жыл бұрын
Would also like to know
@davidduke75315 жыл бұрын
The 3.6 is very well known for #3 misfire caused by a burnt, or sticking, valves. The fuel injector is not the root cause.
@axkiller1985 Жыл бұрын
@@davidduke7531 Good stuff man! thank you, I am dealing with cylinder #3 misfire...
@savedsoul63877 ай бұрын
What is the root cause??
@tawannapierce674 жыл бұрын
Does this apply to a 2009 gmc Acadia? I cant find a video about it.
@Charles-Lawrence4 жыл бұрын
kzbin.info/www/bejne/nJuzqnp8h7miepI
@Charles-Lawrence4 жыл бұрын
There you go if you still need it!
@simonem2006sm6 жыл бұрын
Did you unplug the negative cable from the battery?
@carsonhowell24106 жыл бұрын
simonem2006 I didn’t but you can for extra safety
@luiscorrales20123 жыл бұрын
How many injectors the car have
@jeffcarpenter63063 жыл бұрын
On a 2010 Acadia one of the rails goes into a grove and is a pain to take out. Putting the injectors on first will not work.
@APPLEDUDEZ3 жыл бұрын
You did not show re-installation of all six injectors.
@SirSmokesAlott4 жыл бұрын
20:34 he finally gets the intake off and starts the work on the injector
@100fredkrueger3 жыл бұрын
But he is showing how to take everything apart. I don’t know how to do it so it’s helpful to me.
@SirSmokesAlott3 жыл бұрын
@@100fredkrueger huh? Why are you replying to a year old comment? But nothing, your needs don't have a thing to do with my comment, and are completely irrelevant to me saving time for most people who found this video looking to change injectors, by posting when the actual content titled starts. Taking six bolts out to get the intake off isn't something anyone should need directions for anyways, let alone shouldn't take 20 minutes. You've wasted my time by replying, just like you wasted your time throwing parts and money at your vehicle. It's most likely a vacuum leak causing your issue.
@jms76202 жыл бұрын
@@100fredkrueger you going to let that nigga talk to you like that bro
@billyhesik1735 Жыл бұрын
This video is great to take them off. Need help putting them back on.
@supremevideos5527 жыл бұрын
Sick a great vid. Thanks for your help
@iee4g63 жыл бұрын
I got a 2010 3.6 V6.... with Direct Injection. Currently 16 mpg. Please send me prayers
@hofmanjim6 жыл бұрын
It is a helpful video
@hectormorales5653 жыл бұрын
Should’ve just use liquid Molly 2030 it’s the perfect fuel cleaner