How to Replace Jet Pump Pressure Switch & Change Voltage

  Рет қаралды 50,889

R.C. Worst & Co., Inc.

R.C. Worst & Co., Inc.

Күн бұрын

Пікірлер: 21
@hightide-mcknotts
@hightide-mcknotts 4 жыл бұрын
Thank you for the demonstration and information in this video - I called and spoke to a gentleman named James at the Idaho location to ask a question and he was very nice and took the time to help me with my electrical motor question. I appreciate it when businesses and their employee's - office personnel - technicians etc. answer your phone call right away and are nice and friendly and direct you instantly to someone who can help you. It's a reflection on their company and reputation and i appreciate great customer service - Thank you.
@RCworstwater
@RCworstwater 4 жыл бұрын
Thanks for the awesome review! James is a great asset :)
@catsmeow5566
@catsmeow5566 4 ай бұрын
Ahh! Thank you so much! The pressure switch on my brand new pump had a contact pop off and I was trying to figure out how to remove the pressure switch to put a new one on. I knew how to do the first step of removing the incoming wires, but wasn't sure how it attached. Now I see that threaded piece. That helps. I will need to get those fork terminals for my wires eventually. I'm about to pause the video and go try this before it gets dark. Hmm.. changed the switch but it is making a ton of noise. Chattering very loudly and sounds like it might be short cycling. Ugh.
@timgabriel
@timgabriel 7 ай бұрын
Great videos Chris. I have a Gould 1HPJet pump which sometimes stutter starts, sometimes it starts right away when the pressure drops to 40psi, sometimes it starts, stops, starts very quickly. Pressure tank is set correctly. No air in the system. Any suggestions?
@jasongeorgephoto
@jasongeorgephoto 3 жыл бұрын
Nice video- how do I replace that flexible rubber line please? I have yanked it out of the housing while trying to unscrew it ; is there a beefier trick for this given the plastic threaded components? Thanks!
@sjr7822
@sjr7822 Жыл бұрын
HELP How do you know what brand to buy, I have a burnt-out power switch and I've been on Amazon all day, and can't figure out what to buy. I have a switch on the pump, just like your setup in the demo. it is a 1/2 HP Flotac 4312. Your demo helped if I ever find a switch to buy for the pump. Can't find the FRlotec name-brand switch. does it matter about the brand?
@RCworstwater
@RCworstwater Жыл бұрын
Give us a call: 855.329.4519
@jamesthompson9161
@jamesthompson9161 Жыл бұрын
Hello, I have a new 3/4 hp shallow well pump, that is short cycling on 2 of the 5 zones, any idea why, only on 2 out of 5, ?? New check valve installed also, thankyou,
@RCworstwater
@RCworstwater Жыл бұрын
Do you have a pressure tank installed? It is likely that those two zones are not using enough water.
@jamesthompson9161
@jamesthompson9161 Жыл бұрын
@@RCworstwater thankyou
@jamesthompson9161
@jamesthompson9161 Жыл бұрын
Yes. ,tank installed, it's holding pressure, still wonder if. It bad,
@akilcyrus6289
@akilcyrus6289 4 жыл бұрын
With a name like Worst you have to be the best 😏
@89bavaro89
@89bavaro89 2 жыл бұрын
If I have to change the pressure switch do I have to turn the water off or drain anything? My pressure switch is mounted to the pump like in this video.
@RCworstwater
@RCworstwater 2 жыл бұрын
Yes, you need to turn off power and drain the pressure before you replace it.
@paulwood9043
@paulwood9043 4 жыл бұрын
I have a jet pump wired for 230 volts as I can also reduce it to 115 volts, it pumps water but does not have enough pressure to get past 20PSI as of needle vibrating like shaking at 22 PSI. The starting point is 30PSI to 50 PSI shutoff, the tank has a bladder in it and holds 20 gallons as of 28 PSI set as of the 30 to 50 PSI, it runs steady and will not build up pressure as of pump, so I got to unplug the pump. What could be the problem here??
@RCworstwater
@RCworstwater 4 жыл бұрын
Sounds like it might not be fully primed. Check out our video here: kzbin.info/www/bejne/lYTWhZ1uj9l6gtE
@JohnHansknecht
@JohnHansknecht 6 жыл бұрын
Of course you wouldn't put the raw wires to the input. Must be in a conduit so the wires don't rub on the housing, wear through the insulation and short out.
@ghostlyencountersparanorma6041
@ghostlyencountersparanorma6041 4 жыл бұрын
Y dose my pump keep turning off after I turn it on
@cf4459
@cf4459 5 жыл бұрын
Well that was confusing as hell I still don't know where the wires go.
@RCworstwater
@RCworstwater 5 жыл бұрын
Give us a call if you still have questions: 855.329.4519
@akilcyrus6289
@akilcyrus6289 4 жыл бұрын
Take a pic before taking it apart
How To Adjust a Pressure Switch
7:58
R.C. Worst & Co., Inc.
Рет қаралды 4,9 МЛН
Smart Sigma Kid #funny #sigma
00:14
CRAZY GREAPA
Рет қаралды 88 МЛН
How to Test Pressure Switch on a Furnace
14:14
Word of Advice TV
Рет қаралды 627 М.
How to Change Voltage on a Jet Pump Motor
2:20
Goulds Water Technology
Рет қаралды 85 М.
How To Fix/Adjust A Pressure Switch
4:04
PEX Universe
Рет қаралды 299 М.
replacing a well pump pressure switch (burnt contact points)
8:49
gregpryorhomestead
Рет қаралды 992 М.
Jet Pump Failing Pressure - Check this First!
9:47
Godwin & Sons LLC
Рет қаралды 40 М.
How to Jump Pressure Switch on Furnace
6:56
Word of Advice TV
Рет қаралды 714 М.
Shallow Well Pump | Everbilt Jet Well Pump Installation | The Home Depot
10:19
Hayward Super Pump, Capacitor, Governor & Switch Removal
4:28
WeT HeaD Pump Repair
Рет қаралды 133 М.
How a Well Pump Pressure Switch Works. Diagnosis and Repair.
12:26
FarmCraft101
Рет қаралды 139 М.
Smart Sigma Kid #funny #sigma
00:14
CRAZY GREAPA
Рет қаралды 88 МЛН