√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
@RhinoFeed11 ай бұрын
Got it done, great video! Pro-tip (not that I am a pro whatsoever), if you have a body panel clip remover tool, use that to help you out when trying to remove the hoses from the purge valve. Helped me out more than the flat head screwdriver
@nulife0224 жыл бұрын
Don't know how I repaired my cars before these great KZbin videos - with a lot more wasted time and frustration, I guess. Thanks
@1AAuto4 жыл бұрын
+nulife022 Thanks for checking us out! 1AAuto.com
@larryd4224 жыл бұрын
My jaw dropped when you said “remove the engine.” Lol. 👍🏻👍🏻
@nanoa95763 жыл бұрын
😂
@christiandavid70792 жыл бұрын
This is the best channel on KZbin! Thanks s lot, I replaced the purge valve without problem!
@ryann49042 ай бұрын
Thanks for the clear instructions. Got mine done today no problem
@JayCeeMax4 жыл бұрын
I just replaced the Purge Valve for a 2010 Elantra. The location of components are a tad bit different. I vlogged about the simplicity of the removal and installation as well. Thanks 1A Auto Parts!
@1AAuto4 жыл бұрын
+Jay Cee Max Thanks for the feedback!
@JayCeeMax4 жыл бұрын
@@1AAuto No problem!
@nickenhead500 Жыл бұрын
Thank you I have a Hyundai Elantra 2010 and I am struggling trying to replace the purge valve I can’t disconnect the wire from the valve it is very different from this video.
@herbbradley89582 жыл бұрын
The only step by step video Ive found. Still can't find one for a 2011 Elantra GLS touring
@HungryH19515 ай бұрын
Thanks. Going to carry out this operation in a few days. This video helped.
@tay-basswalker3964 Жыл бұрын
Thanks for the great vid...Would the same process work for a 06 elantra?
@russstedman4 жыл бұрын
You got me with that joke. I was like "WHAAA....oh. Ha ha." Thanks for the instructions.
@leeellis47 Жыл бұрын
Had a 2001 and now have a 2011 and they are such simple cars to work on
@christinecorpse Жыл бұрын
I replaced mine with the help of this video, thank you so much!!
@franklittle81244 ай бұрын
Another solution would be for the states and EPA to provide an exemption to some emission requirements for 15 year and older cars. Even if this valve is stuck open (the normal failure mode), virtually all the fuel vapors still kept from getting into the air. Sure, no car emitting visible or smellable pollution should be allowed, but something like this should be.
@patrickrobinson3174 жыл бұрын
Great instructions - Thanks !!! You are really good at making these videos !!!! Much appreciated.
@1AAuto4 жыл бұрын
+Patrick Robinson Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com
@avrildiaz2803 ай бұрын
Great video, worked perfectly!
@13orangecake11 ай бұрын
Loolz! I almost clicked away when you said, "all we're gonna do is pull the engine outta here" 😅
@hugolob9811 Жыл бұрын
Good work thanks tomorrow I'm going to change my
@frankiphone86999 ай бұрын
Good job mat can you how can I Fix or you should be changing
@yannickallard44 жыл бұрын
Great video!!! Thank you. I still have a question. When i fuel the tank to max it overflows. Does the purge valve correctiion make it okay?
@8bit_bryan Жыл бұрын
I'm looking to replace all of the engine mounts for a 2009 Hyundai Elantra Touring 4cyl. Any thing I would need a heads up on? I have replaced engine mounts on several 4, 6, and 8 cylinder cars before with success. I am helping a neighbor, and I havent found anything in this model year range online for a DIY home garage. "remove the engine" That woke up a lot of viewers! 🤣
@gilsanjang959 Жыл бұрын
hi, thanks for a great video. Do you have a Vapor canister replacing video?
@capbrctv Жыл бұрын
Thank you, I followed your instructions, it’s all good now!
@jimkelley58123 жыл бұрын
Same procedure for a 2009 Hyundai Accent. Only difference is that the Purge Valve is parallel to the ground rather than perpendicular.
@Phunku3 жыл бұрын
Your mistake was using a dorman purge valve. Replaced 3 on my Elantra (within a year) and finally went with Napa which was actually a Bosch part. Dorman electrical parts are about the worse you can use. I’ll never use them on my cars anymore.
@4k_fons Жыл бұрын
Oem part is $25 on Amazon lol
@daby83993 жыл бұрын
Is the purge valve the same thing as a purge solenoid
@Lakobas Жыл бұрын
Thank you for making this easy for me o7
@sameralhourani2063 Жыл бұрын
What is the model of this Hyundai, how much is the engine capacity?
@holguin4sho2 жыл бұрын
Great vids like always
@arashebadtabrizi13014 жыл бұрын
1:22 “just gunna pull the engine out “
@JCTheLawnCareGuy2 жыл бұрын
Could you do a video on this for a 2011 Hyundai Sonata 2.0L ? Thank you.
@Fabin123 Жыл бұрын
Just to clarify. In the 2005 Elantra this part is located in the rear in the EVAP canister next to gas tank correct?
@tonkatoytruck Жыл бұрын
I was really wanting to see it tested to determine if it is faulty. I read that the engine usually misfires when the purge valve fails. Is this true?
@NikkyKnowsUNzs20013 жыл бұрын
Great Training bro much appreciate it!!Keep it coming!!Very professional!!!!
@1AAuto3 жыл бұрын
+Nikola Tesla Thanks for the feedback!
@johntaylor70204 жыл бұрын
I got a P0441 code on my 07 Elantra. Followed this video, drove the car for 60 miles after replacing the valve and still get the same code. I'm curious if I could have put it in upside down or what I could have missed.
@bhf4u4 жыл бұрын
a bad cannister valve will give you the same code.also i would put new clamps on the hoses,weak clamps can lead to vacuum leaks.
@1AAuto4 жыл бұрын
+bhf4u Thanks for the feedback!
@patrickbowley1299 Жыл бұрын
What are the symptom s for a bad purge valve
@andrewcooper67813 жыл бұрын
So my 2007 Hyundai Elantra reads P0444, I’ve replaced both the purge valve, and fuel cap, would next steps be to replace the Catalytic converter or the 2 o2 sensors in your opinion? @1A auto?
@frankiphone86996 күн бұрын
Good job 👍👍👍
@jaimecortez36015 жыл бұрын
How do you know when the purge valve needs replacing?
@RhinoFeed11 ай бұрын
when you get a check engine light
@jmg361913 жыл бұрын
Should I reset the check engine light after replacing this part
@1AAuto3 жыл бұрын
+Jeremy Garcia You will want to clear the codes after the part is installed. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@KRosenChannel4 жыл бұрын
Thank you for this, saved me on the back hose - the driver and twist trick worked, though mine was a lot harder htan yours to get off.
@1AAuto4 жыл бұрын
+KRosenChannel Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com
@robertmaynor72662 жыл бұрын
Ok I have a Hyundai Elantra 2007 I can go to any gas station put gas in it then it acts like it doesn't want to start what could it be after apply gas to it it fires right off and runs ok
@joshdelay67 Жыл бұрын
I have an 04 that’s doing the same thing. Did you figure out what the problem was?
@ShawnOG13 Жыл бұрын
Is it the same on 2015
@angelareneemoll2 жыл бұрын
Does the battery need detached before you unplug?
@gvelasquez91633 жыл бұрын
My EPS (electrical powering steering) light has been on for a few months on my Hyundai Elentra 2010 can you show us how to replace it?
@Joseph-322 жыл бұрын
Is this similar for a 2008 hyundai santa fe?
@TheLatelycrew4 жыл бұрын
I'm getting a reading of P0451/P0455 is this the part I need for that? I replaced the gas cap and was told I may need a fuel sensor...engine light went out but still won't pass emissions
@1AAuto4 жыл бұрын
+TheLatelycrew P0451 (EVAP Emission Control System Pressure Sensor Range) and P0455 (EVAP Emission Control System Large Leak). You could try replacing the valve and see if that helps with the codes.
@stuff_n_thanngs75523 жыл бұрын
The hose you removed at 2:55 i tried pulling off from the other end. The plastic connector broke in half. Any idea what that's called?
@buzoff46424 жыл бұрын
Outstanding video.
@1AAuto4 жыл бұрын
+Buz Off Thanks for the feedback!
@sameralhourani2063 Жыл бұрын
Same for valve found on 2009/2000cc Kia Soul
@jonathanhartmann24004 жыл бұрын
2014 hyundai elantra with p0447. Any guidance?
@nancymench64412 жыл бұрын
Awesome Thank you🔧🔨🔧🔨
@jwhit319954 жыл бұрын
Any videos on 2016 Hyundai Tucson? Same project
@1AAuto4 жыл бұрын
+AirGunGodz We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
@brienbarnes71164 жыл бұрын
Just did this..great video.
@1AAuto4 жыл бұрын
+Brien barnes Thanks for checking us out! 1AAuto.com
@pierremarcsaintil30513 жыл бұрын
Hello my friend I have a car of Kia soul 2012 2.6L today I put my computer on it, I see in ECM one code of P0661 , after I' looking the code on Google , I don't find it, I just text you to do the video about my car to explain me very well what piece is it and where place is it in kia soul 2012 2.6 L. Ok Thank you in advance et for your understanding.
@PT-ie2xj Жыл бұрын
Missing a bracket on the air filter housing probably means unfiltered air is getting past the filter and into the engine.
@daveg40184 жыл бұрын
Same location for the Azeri?
@spookytook4 жыл бұрын
do i have to drain any fluids?
@yates11783 жыл бұрын
will this help with a p0172 code or is that something else?
@1AAuto3 жыл бұрын
+Thomas James Yates We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@mohammedlibya26983 жыл бұрын
How much this kit ?
@liarf24693 жыл бұрын
Will this fix the evap leak P0455??
@xavierduax685 Жыл бұрын
That's what I'm trying to figure out. That's my code right now and I just got an evap purge valve to hopefully fix it...idk what else to get for that.
@craighealy61862 жыл бұрын
It would have been nice if you told us which side was up on those purge valves. I didn't know it mattered and I installed it upside down. My car blew up. Thanks for nothing.
@Simmonsracing1873 жыл бұрын
Is this the same for a 2011?
@1AAuto3 жыл бұрын
+Simmons racing187 It may be similar! We currently do not have an install video for the 2011.
@Simmonsracing1873 жыл бұрын
@@1AAuto thanks for your speedy response
@joemarotta22375 жыл бұрын
Thanks buddy.
@1AAuto5 жыл бұрын
+Joe Marotta Thanks for checking us out. 1AAuto.com
@patrickblue4754 жыл бұрын
Can you do a video for an 2011 Hyundai Sonata?
@1AAuto4 жыл бұрын
+patrick blue We're always cycling through common cars. We'll add this repair to our list! 1AAuto.com
@Whoischristiantho2 жыл бұрын
Bruh I literally can’t take a little metal clamps off, they are strong
@darrinlewis-n6t Жыл бұрын
1:26 Everyone Stomach Sank.
@loveanyce3 жыл бұрын
I’m Still Trying To Find Where The Purge Valve Is Located On My 2013 Hyundai Elantra 🤦🏾♀️
@1AAuto3 жыл бұрын
+Love Anyce The purge valve is located in the vacuum line between the fuel vapor containment canister and the intake manifold.
@loveanyce3 жыл бұрын
@@1AAuto thank you soooo much
@stephanM54 жыл бұрын
Next time just take off the top of the air filter rather than fight with it. Good video otherwise.
@1AAuto4 жыл бұрын
+Thor Thumb Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
@shawnmartian3 жыл бұрын
this is a very underrated comment.
@SilentServiceCode4 жыл бұрын
6:42 the old one doesn't come with a rubber mount? huh?
@gates694 жыл бұрын
SilentServiceCode He mixed them up
@jamesweiland32144 жыл бұрын
He meant the new one. I caught that too :)
@stuff_n_thanngs75523 жыл бұрын
Figure it out
@nestorvillalobos41014 жыл бұрын
What code. What was wrong?
@1AAuto4 жыл бұрын
+Nestor Villalobos Thanks for checking us out! This video was completed for installation purposes. However, a common code for the Purge Valve would be Error Code P0443. You may also notice a rough idle, hard starting, or bad engine performance. If you think you may have an issue with the Purge Valve we would suggest taking your vehicle to a nearby reputable shop to identify the cause. Thank you!