Thanks. So far process worked great. Great video. I’m sure it was difficult to capture all the angles. Some of those areas was very hard to get to.
@unebonnevie11 ай бұрын
The car model here is probably a V6 not a 4-cylinder, as V6 is more complicated. Some key notes: 1) Center the steering wheel/the front wheels and tie down the steering wheel before doing the work. This is to prevent the airbag clock spring from the being damaged if the steering gets turned during the process. (At least, that's my understanding.) 2) Centering the new rack & pinion at 18:47. 3) When putting in the new rack & pinion (at 22:45), make sure the two lines (the high pressure line and the return line) are loosely covered with the plastic cover, then loosely attach the two lines. Then loosely tighten all the nuts and bolts onto the new rack & pinion. Then go back and tighten the two lines' bolts. And finally tighten all the bolts. 4) At 31:10 how to put back the outer tie rods. Looks like in the video he put in the outer tie rod's tiny boot at an angle rather plush onto the flat side of the knuckle. Wouldn't that be a problem?
@lami740311 ай бұрын
thanks for your time bro that's was helpful
@lunacallie68583 ай бұрын
Shop prices are wayyy up so gonna carefully give this a shot😎👍 GREAT VIDEO 😎👍👍
@CheletoVlog Жыл бұрын
Replacing my 2007 and the pressure lines are both 17. Also didn't need a 24 mm for removing the steering linkage. Was a 19 mm. But my new one came with those and control arms.
@samlivingthedream885128 күн бұрын
Good information now allow me trying to fixed my rack and pinion I hope I don’t screw up!!😅
@matjoe272 Жыл бұрын
Thank you very much for showing how its done. Thumbs up.
@wiseguymoney6 ай бұрын
Thank you thank you thank you, this step by step was awesome and made my life easier, and saved me about 800 dollars thx again
@jpadil226 күн бұрын
Excellent video, friend and great shots.
@hudongng Жыл бұрын
Thank you for your v/clip, it’s useful for everyone. ❤
@MacroMicro99Ай бұрын
Great video, better than alldata cause it’s free😂 lock that steering wheel people cause you don’t want to break the clock spring.
@christopherbrown533810 ай бұрын
Excellent video! Is there a way to verify if either the rack or pump is faulty?
@VuNguyen-nk7mx9 ай бұрын
Thanks!
@rogergroover497126 күн бұрын
Great tutorial! Thanks!
@SaidAttalah11 ай бұрын
Amazing! Thank you for sharing.
@jayrocksxxasap12736 ай бұрын
Love the work you do brother. I have a question for you... So i have a 2003 honda pilot.. Only axel that matched up was a 2002 axel... The trans side was just a little bit shorter.. But the axel that was with vins did not match.
@jayrocksxxasap12736 ай бұрын
My question is.. Would that make a whole lot of difference?
@algentles53616 ай бұрын
HI, does the same method work for the HR drive Honda Accord?
@1chip4you6 ай бұрын
Is this close to the same as the newer 09-10/14 accords/tsx’s with the electric power steering just without the fluid?
@TiborPapp-s8e9 ай бұрын
Thank you so much for your help
@MrLuvHaters4 ай бұрын
Do you guys have a rack and pinion video for a 2014 Honda Pilot?
@Светослав-ч2х Жыл бұрын
Thanks a lot very useful clip
@Lifesituations800010 ай бұрын
Is that the v6?
@UserRjt4 ай бұрын
This the same for 3.5l v6 accord 2011?
@creepyscope7824 Жыл бұрын
How bout 8th gen is it the same procedure?
@TRQ Жыл бұрын
√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money
@ericmoralezz3 ай бұрын
how does it cause damage to the airbag system?? when u turn the wheel?
@JaySix-jo8oe25 күн бұрын
V4 and v6 same rack?
@itzjay_1678 Жыл бұрын
What about that plastic yellow piece on the input shaft is it important to reinstall that
@sricharte899 ай бұрын
its all good and all, but helps if you have a lift as is makes it easier also a place to do it in, can be done on your pavement but more difficult to get underneath and do all that
@OGS_6236 ай бұрын
Does snyone knows the exact name of the pliers used to turn the rack before installing. Last tool I nedd before seslping mines. Id greatly appreciate the help!
@2626whwh4 ай бұрын
Would this same procedure work on my 06 TL?
@TRQ4 ай бұрын
+@2626whwh The installation should be very similar.
@paulwodarz46639 ай бұрын
Thank You 😊
@boywonder8175 Жыл бұрын
Good info
@jasonblowers45408 ай бұрын
9:30 I have everything apart and still can't get the rack out.
@zekizeks7 ай бұрын
PLEASE HELP!! WHICH OIL GOES ?? I HAVE ACCORD CL7 2003
@jamesmahle12593 ай бұрын
What about the heat shield install?
@eddroid458511 ай бұрын
Nice man👋👋👋👋👋👋🇧🇷
@sweetdevil6221 Жыл бұрын
Thanks ❤
@mtnfreestyle18992 ай бұрын
Hes rocking that old harbor freight angled driver that they dont sell batteries for anymore
@balkee4211 ай бұрын
Same pretty much as an 07 acura tl?
@TRQ11 ай бұрын
+@balkee42 This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-TRQ
@dummesschwein87278 ай бұрын
I'm more interested on how to get behind than how to take the part out
@wanzhaf93215 күн бұрын
Dont forget to buy some car lift other than steering rack itself guys….😂
@EVO_SE3 ай бұрын
Haha the torque is way over torqued! But it’s all good as a tech my self good and tight will do!
@sashahonda9 ай бұрын
Привіт з України! Дай, будь ласка, опигінальний номер рульової рейки. Дякую.