How to Replace Rear Brake Caliper 2007-2013 Mitsubishi Outlander

Buy Now!
New Brake Caliper from 1AAuto.com 1aau.to/ib/1ABC...
This video shows you how to a (front/rear)brake caliper on your 2007-2013 Mitsubishi Outlander. A worn out or seized brake caliper can create dangerous and expensive problems: overheating, rotor and pad wear, or even total failure. TRQ brake calipers are engineered to fit your specific vehicle.
This process should be similar on the following vehicles:
2007 Mitsubishi Outlander
2008 Mitsubishi Outlander
2009 Mitsubishi Outlander
2010 Mitsubishi Outlander
2011 Mitsubishi Outlander
2012 Mitsubishi Outlander
2013 Mitsubishi Outlander
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oaWB/1A...
• 17mm Wrench 1aau.to/oIB/1AX...
• 8mm Wrench 1aau.to/ofV/1AX...
• 14mm Socket 1aau.to/oaVv/1A...
• 17mm Socket 1aau.to/oaVv/1A...
• Ratchet 1aau.to/oa94/1A...
• Socket Extensions 1aau.to/oaVv/1A...
• Torque Wrench 1aau.to/oage/1A...
• Brake Grease
• Brake Parts Cleaner
• Cloth Rags 1aau.to/ovj/1AX...
• Drain Pan 1aau.to/osk/1AX...
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@chuckaaron2014]

RT rear brake line in way n wont come off, but you can't put a socket or wrench on top caliper bolt. Unreal design

[@Afrattzz1]

The torque spec for the pin bolts seems extremely high. Is that the correct spec?

[@anandkazanka2438]

The best video for rear brakes OUtlander! I watched so many of them now:) Thank you so much!

[@landogamere-bros9419]

Attempting my first caliper replacement. When I disconnect the break line will it only drip as shown here or will it gush out? Should I clamp the line? TYIA.

[@chuckaaron2014]

That upper caliper bolt isn't near the hose, allows you to get socket in there. I got new caliper n rotor and disc brakes. If you've seen 09 Lancer you'll see what I'm talking about. Anyways, I got everything off, replaced everything and still have a grinding sound. I did it twice, I don't see anything rubbing, backing plate is clear yet RT rear is grinding sound and the tire will lock up even after all new parts. Checked new caliper piston and it's free n easy to move. Anything else I mat have missed that would cause that metal on metal sound n occasionally will lock up the tire.? E brakes, shoes look good, the backside of old rotor was perfect yet outside rotor was not pretty at all, small grooves, not deep. I so stumped. Ideas?

[@chuckaaron2014]

I guess everyone is afraid of doing a right rear 09 Mitsubishi Lancer caliper and bracket when caliper bolts round n bolt extraction sockets dont work. Remove as assembly.

[@Blueformdesign]

Great video

[@Acidena]

Why is the new part so clean?

[@Acidena]

The old part ...looks like the new one was put on. Then the video was shot to show how to take off what you just put on.

[@chuckaaron2014]

See how easy that was on Outlander, vs a Lancer. You can't put upper bolt in with brake hose on. Crap design for Lancer rear disc setup

[@chuckaaron2014]

I really wanna see someone remove a 2009 Mitsubishi Lancer Right Rear brake caliper. These vids are not for Lancer nor similar. I've worked on cars all my life, 1st the lower caliper bolt 14mm rounded, no socket or wrench will go on brake line, not hose, they are in the way of socket or wrench. It's always sumthn, then right lower rounded 6 point socket top easy n rounded lower. After sprayed 2 days with pb blaster. A quick 30 minute job just made me lose my mind. Next morning I got this....nope. branch went thru windshield.....lol. such an easy job, never fails on my cars. Customers, no problem. Not mine....Lmao Then rotor, rt rear, scarred up, removed abs sensor, brake line omg, twisted. Made new lines, waiting on my luck to change, soooo, I'll be done by 2023, new yrs resolution. New rotors and calipers w/brackets, new lines n abs sensor Rt rear n Lord help me left rear lower w/heat n bolt extraction sockets lol didn't work. Took a ride on my bike a cpl hrs to clear my head. Came home n just laffed. Good thing Va has 4 months on inspection sticker. Out-of Feb 1st. Not in shop either, outside n I'm so fkn sad. No $$, disabled n loving it. But I try n work, while others live off government. Thanks guys have a wonderful Thanksgiving and be safe, enjoy your family time. God bless