How to Replace Rear Window Regulator 2007-2013 Chevrolet Silverado

Buy Now!
New Power Window Motor & Regulator Assembly from 1AAuto.com 1aau.to/ib/1AWRG00821
This video shows you how to install a rear window regulator on your 2007-2013 Chevrolet Silverado. Most power window problems can be traced back to either the regulator or the motor that drives it. TRQ produces affordable window regulators and motors that are designed specifically to fit your vehicle!
This process should be similar on the following vehicles:
2007 Chevrolet Silverado 1500
2008 Chevrolet Silverado 1500
2009 Chevrolet Silverado 1500
2010 Chevrolet Silverado 1500
2011 Chevrolet Silverado 1500
2012 Chevrolet Silverado 1500
2013 Chevrolet Silverado 1500
Tools you will need:
• 10mm Socket 1aau.to/taTP/1AXAA00017
• Trim Tool Set 1aau.to/tTM/1AXXX00006
• Wire Cutters
• Ratchet 1aau.to/ta2a/1AXAA00016
• Torque Wrench 1aau.to/tafQ/1AXAA00044
• Gloves 1aau.to/twQ/1AXSS00048
• Painter's Tape
• Safety Glasses 1aau.to/trh/1AXAA00343
• Wire Ties
• Pick 1aau.to/tBr/1AXAA00037
• Razor Blade / Gasket Scraper 1aau.to/tgy/1AXAA00280
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@papawayne700]

Thank you for sharing your time and expertise. You gave thorough and easy to understand instructions.

[@mikewayne6608]

Thanks! Just replaced the window regulator in my '07 Silverado.

[@danquinn7880]

thanks for doing the video it took me about 45 mins and saved me over $500

[@MrPoserina]

Great video. Very helpful. Just a tip. I had trouble prying down the pin for the handle. I took a drill and a small drill bit and drilled a hole, on an angle, through the plastic alongside the pin. This allowed me to pry the pin down with a pick.

[@JoJa015]

Very clear instructions! Thank you for taking the time to create the video.

[@chuckgladfelter]

Thank you for this video!!! One thing to note is there isn't any need to remove the inner door handle as it's attached to the door panel. All you have to do is move the handle to allow access to the bolt.

[@homegrownbrick4227]

Just followed this video for my truck. Excellent step by step guide! Thank you for the video!

[@smuffysimmons]

Great video! Easy clear instructions that saved me hundreds. Thank you!

[@johnluszey1734]

Thanks A Million, really helped me out with my 2010 Silverado

[@donpaine8953]

The cable has come off the rollers how do I get it back on the top one

[@asiakalis9386]

So do you make sure the window is lined up. I didn’t see that before it was put back together.

[@matthewwarwick2272]

This video was a life saver! Thank you!

[@Kramreliwted]

Best video ever 👍👍

[@PureNationalism13]

How tf am I gonna roll up the window of my regulator is broken my dude

[@RPeterson-vr1rr]

Very helpful video. Thanks.

[@mikegarrett861]

2007 right rear window will not go down from driver switch. replaced both front and rear switchs. you can hear a click but won't go down but will go up...? Any idea..?

[@joelkline6897]

The bolt that attaches near the regulator motor will not release. It just spins. Any suggestions?

[@rob9155]

Just totally skipped how to realign the clamps with the bottom of the window. Just plug the switch back in yet again and run it up until the tray hits the window edge and stops, I reckon.

[@lazarogil4688]

Belgian Belgian b😮b😮😮😮😅