How to replace Tensioner pully on 2007 Chrysler PT Cruiser

Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic.

[@xiebunlian]

Muchas gracias, en verdad me ayudó mucho tu vídeo, con muy buena información y detallada, bendiciones para toda tu familia y para ti en especial🙏

[@RBTheMechanic]

Welcome

[@georgerapolai]

These videos are very helpful really

[@davearce3115]

5min ? It takes about 10 minutes to bring the car in the shop and put it on the lift . Then ten to take the tire off an remove the cover . So it's not a 5 min job

[@RBTheMechanic]

Than it take 10-15 minutes to creat repair order 2-3 minutes to walk to the car get in the car .3 seconds to turn the key 1 minute to get out of parking ….. so once’s it on the lift how long dose it take? Calculate accurately u need the impact gun socket and air line connect air line lift the gun up put the sock on to lug nut please calculate for us

[@Wakeupandsniffthecoffee]

My 2001 tension pulley bolt almost comes out and then hits the frame. I may have to loosen the engine and drop it some to clear the frame. 😖

[@RBTheMechanic]

How? Broke?

[@robertchrisop6623]

Why is it when I put a new tensioner assembly on a 2005 PT Cruiser and my new belt is lose on it now and now how I'm I going to get it tight up

[@RBTheMechanic]

Did u check to see if ur belt routing is correct? Or the belt is same length

[@stephaniecandelaria8141]

This is a good video..would love to see how to get to it..like going from under or above the engine.. removing what Items to get into that space..I have a 2005 pt limited edition 5 speed 2.5 or something like that and its sqeeling after the radiator cap gasket melted away and it put water every where ..I thought it would go away after awhile of driving however it hasnt..

[@RBTheMechanic]

Stephanie Candelaria yeah replace it and usually the pullies goes bad also change it if u feel the bearing is bad. Please subscribe also subscribe to my other channel the name is rc usa 201

[@hoodboss4267]

My belt falls of I just change the tensor and power steering pump and pulley and keeps falling out any suggestion ? Thanks

[@RBTheMechanic]

Check if routing is correct and everything is aligned

[@leslielewis9867]

Do u have to take off rotary n everything to get to pulley or just take off fender well cover

[@RBTheMechanic]

Cover only that’s alll

[@noreinvaldezbriones280]

Se safa la banda me dijeron que posiblemente este es del motor donde va el tornillo ,ya está barrido ,y por eso se afloja la polea

[@RBTheMechanic]

Sorry idk Spanish

[@alejandroliberato7215]

Buena información 👍

[@bigmike4720]

I can't get pulley bolt out ot mine because frame in way did you have this problem if so how you do it

[@RBTheMechanic]

It should come out or u can lower the engine by removing mount but u have to support the engine first but I think u can simply yank it down a bit

[@bigmike4720]

@@RBTheMechanic I heard you can jack up back of transmission too and it will tilt motor down enough to remove bolt is this true because its hitting my frame

[@RBTheMechanic]

@@bigmike4720 that makes sense worth the try

[@josephkelley1249]

Load noise when I turn a/c on high and not blowing cold air any suggestions

[@RBTheMechanic]

joseph kelley check see if u have bad pullies or the ac cinoressor

[@rudysison9010]

Have you replace alternator belt tensioner

[@RBTheMechanic]

Rudy Sison no sorry don’t have video on that

[@rudysison9010]

@@RBTheMechanic thanks for responding