How To Replace the Chain and Sprockets on a Yamaha TW200

After riding my Yamaha TW200 over 13,000 miles, my stock front sprocket is finally worn out to the point where it's skipping teeth under heavy load. The rear sprocket was replaced with a 47 tooth shortly after buying the bike new. The chain was also replaced at about 7000 miles since the stock chain stretched out quickly. Now it's time to replace both sprockets and chain because mixing new and old parts together will cause them to wear out quicker. So it's best to replace everything all at once unless the bike is brand new. I will be using an X-ring chain and slightly tweaking my gear ratio this time around. I hope you get a lot of value out of this video and thanks for watching.
Disclaimer: You are solely responsible for working on your own bike. If in doubt have a professional Mechanic service your motorcycle.
Skip ahead to the part you need
Front Sprocket: 4:03
Rear Sprocket: 10:38
Chain: 14:26
Test Ride: 19:14
Calculate your Sprocket change here: sprocketcalculator.com/
My sprocket setups
Stock: 14/50 (base)
1st change: 14/47 (6.4% change)
2nd change (the one in this video) 15/50 (7.1% change)
Specs:
Oil drain plug: 43 nm, (31 ftlb)
front sprocket bolts: 4 nm, (2.9 ftlb) [use locktite]
left crank case cover: 7 nm, (5.1 ftlb)
shift lever: 10 nm (7.2 ftlb)
footrest bolt: 60 nm, (43 ftlb)
rear sprocket bolts: 35 nm (25 ftlb) [use locktite]
rear axle bolt: 90 nm, (65 ftlb)
chain slack 30 - 60mm
brake pedal freeplay 20 - 30mm
check out the parts and tools:
Sprockets and bolt kit in the video were purchased here: procycle.us/bikepages/tw200.html
Find the same exact Sprockets and other parts here:
Rear Sprocket (JT Sprockets JTR1842.50): amzn.to/2GYQHxx (paid link)
Front Sprocket ( PBI-733-15): ebay.us/wXVgpK (paid link)
D.I.D. 428 VX 126 link X-ring Chain (one used in the video): amzn.to/2EsjrNp (paid link)
Extra 5/16 x 3/4 washers (in case you don't want to buy the bolt kit): amzn.to/2U50cyH (paid link)
TW200 rear sprocket lock washers ( part# 90215-08160-00) (3 needed) www.partzilla.com/product/yam...
Yamaha left side cover gasket (part# 3AW-15451-03-00 ): amzn.to/33FMbx5 (paid link)
Tools:
Chain Breaker: amzn.to/2EqBsLS (paid link)
1/4in torque wrench: amzn.to/2NntypD (paid link)
3/8in torque wrench: (don't have this one yet but i'm going to get it because my craftsman one is not great): amzn.to/2BL7oZO (paid link)
(I may get commissions for purchases made through links with "paid link" next to them)
If you want to send me mail:
TDubsKid
P.O. box 286
Sedalia, CO 80135
find me on social media:
instagram: tdubskid?h...
facebook: / tdubskid
twitter: thetdubskid?lang=en
music:
www.epidemicsound.com/referra...

[@TDubsKid]

Skip ahead to the part you need Front Sprocket: 4:03 Rear Sprocket: 10:38 Chain: 14:26 Test Ride: 19:14 Calculate your Sprocket change here: sprocketcalculator.com/ My sprocket setups Stock: 14/50 (base) 1st change: 14/47 (6.4% change) 2nd change (the one in this video) 15/50 (7.1% change) Specs: Oil drain plug: 43 nm, (31 ftlb) front sprocket bolts: 4 nm, (2.9 ftlb) [use locktite] left crank case cover: 7 nm, (5.1 ftlb) shift lever: 10 nm (7.2 ftlb) footrest bolt: 60 nm, (43 ftlb) rear sprocket bolts: 35 nm (25 ftlb) [use locktite] rear axle bolt: 90 nm, (65 ftlb) chain slack 30 - 60mm brake pedal freeplay 20 - 30mm check out the parts and tools: Sprockets and bolt kit in the video were purchased here: procycle.us/bikepages/tw200.html Find the same exact Sprockets and other parts here: Rear Sprocket (JT Sprockets JTR1842.50): amzn.to/2GYQHxx (paid link) Front Sprocket ( PBI-733-15): ebay.us/wXVgpK (paid link) D.I.D. 428 VX 126 link X-ring Chain (one used in video): amzn.to/2EsjrNp (paid link) Extra 5/16 x 3/4 washers (in case you don't want to buy the bolt kit): amzn.to/2U50cyH (paid link) TW200 rear sprocket lock washers ( part# 90215-08160-00) (3 needed) www.partzilla.com/product/yamaha/90215-08160-00 Yamaha left side cover gasket (part# 3AW-15451-03-00 ): amzn.to/33FMbx5 (paid link) Tools: Chain Breaker: amzn.to/2EqBsLS (paid link) 1/4in torque wrench: amzn.to/2NntypD (paid link) 3/8in torque wrench: (don't have this one yet but i'm going to get it because my craftsman one is not great): amzn.to/2BL7oZO (paid link) (I may get commissions for purchases made through links with "paid link" next to them)

[@getsum697]

Very humble of you to do that, most would not like people skipping through all their hard work. Good quality to have in a young man.

[@efirizaki5656]

@@getsum697 specs.... Me sub

[@getsum697]

@@efirizaki5656 Caveman much?

[@benpitts646]

Thanks

[@martymartian9820]

Talk about a mature dude. I’m a 70 year old career gear head and your vids are quite professional. Not a bunch of useless, unrelated yak. Good job with your camera work and editing. Even a dummy could do his own maintenance.👍👍👍

[@TDubsKid]

Hey I appreciate that! Always try and make these videos as quick but info packed as possible

[@martymartian9820]

@@TDubsKid Me again. I do almost all my own wrenching for my vehicles. Presently, my son and I have 14 bikes. 10 are vintage like the Kawasaki 500 triples. Some old YSRs and JT 1 Yamahas . I also have a Grom and my ‘87 TW. So I’ll play around with the carb on it it soon. The Welch plug is out. But the bike generally runs crappy. Back firing while de-accelerating down hill and hesitations and low power. I live on the west coast of British Columbia but ride at all kinds of elevations. Do you have a video of what can help these carbs or should it be replaced? Thanks my friend.

[@ambikesandboards]

Thank you I watched this at least 5 times while doing my repair. It was a lifesaver

[@TDubsKid]

no problem! glad to help

[@bwxmoto]

That must have taken FOREVER to film and edit! Nice vid dude

[@TDubsKid]

haha sure did! but I think it was worth it if people get value out of it plus I won't have people asking me to make a video about it now 😂 thanks man

[@bwxmoto]

TDubsKid hehe yeah lots of people will be watching it for years, maybe decades. Well worth the effort!

[@TDubsKid]

haha very true, best to make it the best I can so I don't have any regrets, thanks

[@jacobquast6535]

That is by far the best like how to video I have seen keep up the amazing work.! Also I have not been on a bike in 4 years your videos popped up on my feed and you have me sold I'm buying a tw200 and getting back into it!!

[@olcraigsen]

Really an informative video thanks so much. Especially the corny first part thanks so much, humor will get us through most anything. May God bless.

[@paulmorneault5789]

Excellent vid. I'm probably twice your age, used to be an aviation mechanic and own a TW200. Your vids are fantastic with accurate info, thorough content and have been helpful. These little bits may help. Chain adjustment: Because of the slop between the hole in the snail adjuster and the axle, after adjusting both snail adjusters and before tightening the axel nut, I take a mallet and tap both ends of the axel toward the front of the bike. The axel will move forward a little and this takes out any slop between the snail adjusters and axel ends, eliminating any misalignment of the axel due to this slop. I also wrote on the swing arm, with a paint pen, the axel/nut sizes and torque spec. This way I just grab the right tools and go to work. Changing rear sprocket: I simply used an open end wrench to hold the bolt heads while turning the nuts on the back side, both during disassembly and reassembly while torquing from the back side. This eliminated both the need to replace the lock plates and the work associated with straightening and bending the tabs on these plates. It is also important to degrease fastener threads when using lock-tight. Break cleaner works well. Any lubricant left on either the male or female threads will interfere with lock-tight's ability to hold as intended. Keep up your awesome work and humble ways. You are an inspiration to us all :)

[@TDubsKid]

thanks, and that's awesome! so much appreciated 😃 that's a good idea, I usually push it snug up against the adjuster with my hands but that makes things easier, such a good idea. yeah I would have done it that way and probably could have gotten my flex head torque wrench back there, would be nice not having to buy new lock washers. thanks for all the great info, i'm sure others will find it useful. so much appreciated 🙂

[@MadTrapper1]

Very impressed by your thorough explanation and clear speech.

[@TDubsKid]

Thanks!

[@brianwhite6496]

Great video. No unnecessary garbage that wastes too much time. Beneficial info. Well done

[@TDubsKid]

Much appreciated!

[@Rockynight]

Thank you for all your videos! My wife just bought a 2019 TW 200 and I am learning so much on your channel! Thank you!

[@TDubsKid]

hey no problem, thanks for watching! that's awesome 😃🏍 glad your finding the channel useful! your welcome

[@consensuallycasual2697]

I don't even have a motorcycle and I watch your videos, good work.

[@TDubsKid]

haha that's what I did before buying one! thanks

[@MrToad-actual]

I thought you were dead man! Good to see another vid! Keep it up fella!

[@TDubsKid]

haha yeah I was gone a while, this video took me way longer than I had intended. thanks! ill keep the videos rolling 🤓🎥🏍⛺

[@davidswearingen432]

Excellent video Dubs. I love your tutorials and all your videos. That must of been a lot of editing and time consuming. Definitely appreciate all you do for the TDubs family. Please keep up the good work and thank you.

[@TDubsKid]

thank you! glad to hear you enjoy the content 😃 for sure it was quite a lot of work but well worth it if people get value out of it. no problem! thanks so much for watching! ill keep the videos rolling

[@florcervecera]

So glad you posted this! Awesome video. Realized I need to order more parts before I start! Thank you :)

[@TDubsKid]

No problem! Glad it was helpful, your welcome 😀

[@tylerculver8514]

Yet another Great video!!!! Thanks for all the great tips and info, you make owning a TW so much easier!!! Keep em Coming!!!

[@TDubsKid]

thank you! no problem, ill keep the videos rolling out 😃

[@CoreyBrass]

Your such a nerd...and that makes me love watching your vids all the more. Good job and I can't wait for your camping video. 🖒

[@TDubsKid]

haha thanks! I take that as a compliment 🤓🎥🚲 it won't disappoint

[@jimburger9418]

I don't own/ride a TW200, but I enjoy watching your videos all-the-same; they are interesting, informative, and fun. You also have some serious chops when it comes to filming and editing. Thank you.

[@TDubsKid]

any bike is good! glad you still enjoy watching the videos. so much appreciated, it's always fun trying to improve with every video, thanks! and your welcome 😃

[@theinfinitryda]

Excellent how to video.

[@TDubsKid]

thank you!

[@tichigantim2]

Thanks for all your very well done videos. They prompted me to get back into off road riding after years away from it. As a result I got a tw200 and am using your videos to add accessories. Fantastic job on your part!

[@TDubsKid]

hey no problem! thanks for watching 😃 so good to hear, ill keep the videos coming, ride safe and have fun 🏍😎

[@joesjunkgarage]

Thank you for providing this very informative video! Fantastic maintenance information that applies to any motorcycle. Always enjoy watching your videos!

[@TDubsKid]

No problem, glad it was helpful! Thanks for watching

[@rjwade00]

Every detail considered, exactly what I aspire to in my projects. Great job man, and thanks for the share!

[@TDubsKid]

yeah got to pay attention to detail, can really pay off. thanks for watching !

[@billsmythe8169]

Very nicely done. I don't need the knowledge but completely enjoy watching your videos.

[@TDubsKid]

thank you! glad to hear you still enjoy them, the next video will be motocamping 😃

[@cudaker]

So Confident that I "like" before even watching ..Great video.. very usefull Step by Step .Thanks for doing it ;)

[@TDubsKid]

haha i'm glad the video don't disappoint 😃 thanks! no problem

[@cesarpaints7435]

Thank you so much. Your efforts are appreciated by all tw owners ! You Save me so much money on labor. I have the confidence to do it on my own thanks to u .

[@TDubsKid]

no problem! glad to know the how to videos are useful :) that's great! you indeed save soo much when you learn to do it yourself and you know for sure it was done right

[@Fanatiktik]

Hey man, thank you for all your work, I've got a tw 125 and all your videos are really helping!

[@TDubsKid]

hey no problem! glad the videos are helpful 😀

[@TheJohnreeves]

I'm super glad you got your TW just before me, you always come out with the maintenance videos before I have to do it! Great video, thanks. I'll probably be doing a new rear sprocket to lower my 55mph RPM a bit.

[@TDubsKid]

haha, good to hear it's been great timing, thanks! nice are you going with a 47?

[@whitecompany18]

Great job buddy, almost camping season here, still got snow in a few high places but the last couple of days have been gorgeous so spring is on it way at last ! I can't wait to hit the road for a few days so I'm looking forward to your video.

[@TDubsKid]

thanks Pikey! for sure, I got a few more months till then haha, it just dumped snow last night, but motocamping is going to be great, I kind of like having a winter so riding and camping is like new all over again. nice! the next one should be pretty good

[@cwo8771]

This is probably the third time I’ve watched this. Especially helpful now as I am preparing to pull the engine. You vids are so much more helpful than the black and white photos and relatively sparse detail in the in the maintenance manual. Thanks, Tdubs! Coronavirus self-quarantine is a great time to kickstart this old project. Stay healthy and God bless!

[@TDubsKid]

haha nice. glad to hear it was helpful, best of luck on the project! no problem, great time to something productive at home. you as well! thanks and God bless 😀👍

[@OnceUponASundayxxx]

you're making some of the highest quality videos, especially how-to videos on KZbin, props!

[@TDubsKid]

thank you, so much appreciated! 😃

[@backcountryadvmoto]

Awesome video. Very Detailed and nice edits. Going to a 15/50 on my newly purchased TW and this was very helpful

[@TDubsKid]

Thanks, Glad to help! Its a good ratio

[@joehaleyquesnel9985]

Dude thank you for this video. I literally just ordered my chain and sprockets a few days ago, you're saving me so much time ,money and headaches!

[@TDubsKid]

hey no problem! perfect timing haha

[@garthhowe297]

This is the best filmed/narrated "how to" video I have seen. Excellent work!

[@TDubsKid]

+Garth Howe thank you! Glad to hear you found it useful!

[@wp8767]

You the best with these T Dub videos!

[@TDubsKid]

Hey thanks!

[@alfredramirez4534]

Hey there, I just wanted to give you a shout out for the informational videos you out out there. I have learned a lot regarding my 2021 TW.

[@TDubsKid]

hey thank you! glad they have been helpful 😃

[@smoguli]

Thank you for this video, I just changed my rear sprocket on my new to me 2017 TW, and it was easy by following your instructions.

[@TDubsKid]

your welcome thanks for watching! glad it was helpful. ride safe 😃🏍

[@glug1252]

Great how to video!! Appreciate you taking the time to film while doing these projects and editing it all. Just did this swap and your video was extremely helpful. I did however use a DID Xring chain with 124 links, but still had to remove a link for it to fit properly for some reason 🤔 Anyways keep up the good work, and looking forward to your next video!

[@TDubsKid]

hey thank you! no problem, glad it was helpful. better to have too many links than not enough, glad it worked out, thanks! i'm working on the next one already

[@kkooloo5781]

Your a genius mechanic .Best how to vids on KZbin.Thanks for the effort it cannot be easy!👍from England🇬🇧

[@TDubsKid]

Wow, thanks! much appreciated, these type of videos do take a while to produce haha 😃

[@probablysomedingus75]

Currently waiting on a '22 TDubs for my first bike. Your channel helped me decide on what to get, and I fully plan on using your vids as a reference!

[@TDubsKid]

Very nice! Hope you got it by now. Glad to help

[@bobdrakeford5731]

Great video. Your explaination was excellent. Very well done TDubsKid! 👍😊

[@TDubsKid]

thanks you! 😃

[@CD-hc5ds]

Just purchased a 2012 TW. Your videos are wonderfully done & so detailed! Im fairly decent at wrenching on things but you make it easy to follow & cover everything so the little stuff isn't overlooked. Thank you for all the time & effort you spend doing your videos their very appreciated!

[@TDubsKid]

congrats on getting a TW! thanks so much. glad to hear the vids are helpful! no problem, thanks for watching!

[@ianferrier235]

Thanks tdub.Great that you included torque specs 👍👍

[@TDubsKid]

No problem! Thanks for watching 👍

[@johnnywishbone932]

No clue why but your videos make me happy and relaxed. I think it’s just your pure love of your bike. I get it. It’s a true love story! 😀

[@TDubsKid]

Haha

[@187musashi]

This video is SO helpful. Thank you for the time it took to do it. I'm working on this job now and I've watched it numerous times to make sure I don't screw anything up. The biggest problem is the panhead screws in the case not wanting to come out of my 2000 TW. I'll deal w/ that today. Thanks again TDubsKid.

[@TDubsKid]

glad you found it helpful! no problem, oh yeah those can be a huge pain, the are jis screws similar but different than Phillips. you can replace them with regular hex bolts

[@Mascotal]

AWSOME video Kid. I will refer to this when the time comes.

[@TDubsKid]

thanks! hope it will be helpful

[@alexicon_]

immensely helpful video!!! excellent instruction, and great camera work catching all the small important details. thank you very much!

[@TDubsKid]

Glad it was helpful! your welcome

[@ricklieberson5576]

This is a great vid and you are a very good teacher my friend! About to change the rear sprocket and chain on my wife’s new TW and this video really helped. I’m happy subscriber.

[@TDubsKid]

glad to hear! hope it went well, thanks for the sub!

[@Half-Time_Paul]

Keep going to with videos! You have saved me a lot of money and time by giving how to videos

[@TDubsKid]

Ill keep them going. Spending a lot of time on the van lately but I got more tw videos coming

[@getsum697]

Thank you for your videos and all the hard work you put into them. Even though you are young, you have a lot to teach on this bike. Keep up the great work!

[@TDubsKid]

You are very welcome! glad you find the vids useful. ill keep them coming

[@getsum697]

@@TDubsKid Used your video today for bleeding the brakes...it is a bit different than a car's. Turned out great and I didn't have to beat any dinosaurs off me while doing so! I'm a member of the TW200 forum and we all love your work. You are young and probably do not realize the impact your videos are having. I personally want to send my appreciation for sharing your walk with God in one of your videos. As you mature your relationship with Him will change, as it seems to be happening with you. This world, as beautiful as it is is and shown through your videos, is not our home. Keep up the great work and strive for the best relationship possible with God, He'll never let you down.

[@TDubsKid]

Getsum hey glad that video was useful! Haha thats always a plus 🤣 glad to hear, for sure, God is good! Amen to that 🙏

[@lawrencepearson4362]

very good video, looking forward to the Moab vid. Hope you enjoy the trip, from what I've seen on other youtube channels it looks fantastic.

[@TDubsKid]

thank you! so much appreciated. I can't wait, it will be my first time going to moab, should be a blast. will make for some great videos 🤓🎥🏍 it does look great from the photos and videos!

[@DarylMcGann]

Wow! Super informative!! This was enjoyable and VERY helpful… thanks!!

[@TDubsKid]

glad to hear! and glad to help

[@thewatcher5271]

Yeah, You're Either A Motorcycle Mechanic Or Should Be, Because Your How-To Video Tutorials Are Exemplary! You Have The Right Combination Of Patience, Disposition & Demeanor.

[@TDubsKid]

Im actually mechanic for a luxury car brand haha, thanks

[@gholden91]

Thanks for taking the time to make these amazing videos. Makes working on my bike a breeze Now I just need you to buy a DRZ400.

[@TDubsKid]

hey no problem! glad you found them helpful thanks for watching. a DRZ400 would be cool to have haha

[@Burton61RnD]

Great video as always and very informative!

[@TDubsKid]

thank you! good to hear you enjoyed it!

[@blackbodom]

Great work! So much great info and editing! I'm still running the stock chain and it slipped off last summer and jammed between the sprocket and swing arm locking up the rear, think its time for a new chain this spring haha

[@TDubsKid]

thank you! glad you enjoyed it. dang that's no good hope you didn't get hurt, I'm surprised mine didn't fly off when skipping teeth. indeed, the stock chain stretches insanely fast haha

[@Adv4x4]

Awesome video man. I'm a Auto tech and it's apparent you have some back ground in a field or are a well studied diy guy. Impressive attention to detail! Reminds me of how I carry out my work on cars 👍🏼

[@TDubsKid]

thank you! i'm an auto tech too haha yeah I do pay attention to detail. glad you do too it seems to be important. 😀

[@MathieuTechMoto]

wow i didnt know that was this big job on a tw200, great video !

[@TDubsKid]

yeah they made it a pain on this bike for some reason haha. a high quality chromoly front sprocket should outlast the stock one by a lot. thanks!

[@TheSmallSalmon]

Enchante Tdubs and your beautifully put together pieces.

[@TDubsKid]

thank you 😃🏍

[@dustydualsport4366]

Great video! I have a XT225, which is a close sibling of the TW200. I learn a lot from your videos that I can apply to the XT225. This project was significantly more involved than the same work would be on the XT225. I’m also making my first Moab, UT trip with the XT225. I’ll be there 3/17 through 3/19. Would fun if our paths crossed.

[@TDubsKid]

thank you! nice the XT225 is a great bike. yeah way more work than just removing a plastic cover you do on the XT225, it's cool that bike is a 6 speed too. nice haha! we will be leaving to go back on 3/17 would be cool to see ya

[@offdeadeye88]

My 88 two is due this will help with sprocket choice thanks

[@TDubsKid]

gotcha, i'm glad this video helped

[@bennyhanna1976]

Another great video!

[@TDubsKid]

thank you! 😃

[@tookymax]

Thanks for making such an imformaive video. Just what I needed. Love your videos.

[@TDubsKid]

You are so welcome! glad it was helpful. thanks for watching

[@tookymax]

@@TDubsKid Got a 44 rear and a 14 front installed. Testing tomorrow.. The 428 chain with 118 links fit perfect on #1 snail. That calculator site said 106 but it is full of popups and hard to use. You were partly the reason I bought the TW. The other reason is that the Sondors Metacycle I ordered in May 2019, is about 6 months late and I wanted a bike for this season not for 2022. Best wishes to you, ride safe!

[@mopar3i839]

Man id let you work on any of my vehicles, great job, and great video.

[@TDubsKid]

thanks man that means a lot 🙂

[@scooterprint]

Wow. How do you only have 9.9k subscribers??? Perfect video! You have my sub sir!

[@TDubsKid]

haha thanks man, much appreciated 😃

[@markbrock8662]

You really did a nice job on this video. Thank you!

[@TDubsKid]

Glad you liked it! no problem

[@blakpete91]

Another great and informative video!

[@TDubsKid]

good to hear, thanks!

[@gillianaustin5849]

Thankyou for sharing this maintenance video. This probably helped someone somewhere by now. My Regards Mr. Dominic James Austin.

[@TDubsKid]

hey no problem! I hope so, this took me a long time to make. thanks

[@bobgarwood5333]

Thanx for you advice on the oil seal...agree, why replace it if it isn't leaking! Keep up the great videos! Fun to watch and lots of interesting tips!

[@TDubsKid]

No problem! Yeah mine still doesn’t leak at 17,600 miles. Thanks, will keep them coming

[@ericcraigo3432]

Just picked mine up today! I feel like Yamaha owes you a percentage of t dub sales lol. Some of these videos are borderline PBS informational documentaries!! Thanks!!

[@TDubsKid]

nice! congrats. haha thanks, glad you enjoy them

[@alexmacdonald258]

Following your wise advice, since it's been decades since I worked on motors, took the TDub to my LBS, and had both sprockets changed, as well as new bars & risers added, and a USB port hooked up. Haven't had the chance yet to get her out on the highway, but on the forest roads she's noticeably faster. On our 2 lane blacktops, even though the speed limit's 50mph, pretty much everybody goes 60+! Your vids are great, and little by little I'm getting back into working on the bike myself. Thanks for such detail and great presentation, it really helps!

[@TDubsKid]

some great mods for sure! yeah it's not a fast bike but not too bad on 55mph roads for a little bit. good to hear. have fun!

[@ronaldembree3932]

Great video, now I am inspired to finally change my rear sprocket to 47 and get a new chain

[@TDubsKid]

thanks! nice, the 47 was soo worth it, I'm really liking the xring chain as well

[@ronaldembree3932]

Well got a new xring chain and sprocket, went on easy. Well except I used a pair of vise grips and small nut to press home the master link. Also checked the valves after watching your video and that was easy also, great job. 9000km and no adjustment needed, lucky eh? Thanks again.@@TDubsKid

[@EnigmaticPeanut]

i discovered the tw200 this year and fell in love. now i cant stop thinking about getting into it, im new to motorcycle. your videos are useful and fun. thanks for the uploads.

[@TDubsKid]

nice! it's such a fun bike that just works. hopfully you can get one this summer. no problem, glad to hear you enjoy the content!

[@EnigmaticPeanut]

@@TDubsKid i found a 1987 tw200 in good condition near where i live... if i cant get a better one, ill be riding that one next summer : ) Thanks !

[@TDubsKid]

very nice!

[@jy5x5e]

Nice job on the video, very helpful for me as I am about to do this to my bike as well.

[@TDubsKid]

thank you, Glad to hear it!

[@adisyamadasa4238]

Just yesterday I was thinking where is TDubskid, good to see another great video:)

[@TDubsKid]

haha yeah probably the longest I have gone without uploading, this one was very involved. thanks! 😃

[@adisyamadasa4238]

@@TDubsKid Thanks for reply, you are doing a great work. Hard to find videos like this, done in a mode of goodness, very clean and easy to watch. I'm sure it takes a lot of hard work.

[@TDubsKid]

no problem! much appreciated. yeah it's a lot of work but well worth it if people get value out of it! thanks

[@magnumdi1]

dude this is a excellent video. great job

[@TDubsKid]

hey thank you, much appreciated

[@dragolino1000]

Awesome vid perfectly explained !!

[@TDubsKid]

thank you! good to hear 😃

[@bags4930]

Great job, Wes!

[@TDubsKid]

Thanks Jesse!

[@ChathuraRR]

I also replaced the both chain and the two sprockets few days back. Three teeth were broken in the front sprocket. Had to replace the rear sprocket bolt also as threads were damaged. Great video btw and keep it up. Love from 🇱🇰 🇱🇰 🇱🇰

[@TDubsKid]

nice! oh wow, i'm was not too far off from breaking teeth completly off, dang, at least you wont' have to worry about it for a while now that it's all reaplaced. thanks! ill keep the videos coming 😃

[@usernamemykel]

I don't have a TW 200, neither do I expect to purchase one, but that's ONLY because I don't do any off-road riding. I have a 2018 Kawasaki Ninja 400 ABS KRT, and a Genuine Buddy 50 scooter (45 mph, BTW). So, why did I "like" and "sub"? Because your tutorial was very clear, very well produced, and I appreciate your effort. BTW, I doubt that your dinosaur can "whup" Godzilla, even with Godzilla's right rear leg tied to his tail.

[@TDubsKid]

gottcha, that's cool! it don't matter what bike you have as long as you ride it 😃 thanks so much! LOL 😂

[@mileswhoami3847]

Great vid thanks for the info about the torques and stuff

[@TDubsKid]

hey no problem! I also added the specs to the description so they are easier to find whenever you need them

[@rolf9280]

Well done! A perfect "how to" video that covered all the things to look out for. Looking forward to the camping videos! ✌️

[@TDubsKid]

thank you! glad to hear you enjoyed it! it should be good! 🤓🎥🏍⛺

[@rolf9280]

Are you guys freezing up there?

[@TDubsKid]

yeah haha but I have 6 motocamping videos filmed from last summer

[@rolf9280]

Did you notice any difference in pulling in 1st or 2nd gear? Is it still a tractor in low gear?

[@TDubsKid]

from stock yes there was a big difference, but going from 14/47 to 15/50 didn't really notice much difference maybe slightly but not much, it's still a tractor in low gear though haha

[@theephemeralglade1935]

Man, this video got the full on Happy Fun Ball disclaimer, lol.

[@TDubsKid]

haha I guess so

[@michelleellis6790]

Thanks so much for this! I just got all my parts from Pro Cycle and am about to do this job for the first time. I will be watching your video step by step!

[@TDubsKid]

Nice! Best of luck, make sure not to pinch wires with the cover. Lot of people contacting me who did that

[@michelleellis6790]

@@TDubsKid I ended up unplugging the wire bundles from the top to make it easier to route them. That worked well, but I think that was the hardest part of the job!

[@KM-os4be]

You do a nice job on video and working on your bike.

[@TDubsKid]

thanks! 😃

[@theonehavingthekey5966]

Great tutorial!

[@TDubsKid]

Thank you!

[@ridgetop8161]

Dang, nice job! Thanks for this vid.

[@TDubsKid]

thank you! no problem 😃🚲

[@panyalvius1]

Awesome .. yamaha should pay you for such detailed videos of their product man.. and i can imagine the amount of efforts put in to compile the video n the angles to shoot with apropriate light effect .. you are awesome ..

[@TDubsKid]

haha thanks man, that would be cool but either way ill keep making them to the best of my ability 😃 yeah it was quite a lot of work! but well worth it if people get value out of it

[@panyalvius1]

@@TDubsKid hatssoff mate .. keep up the good work... cheers

[@TDubsKid]

thanks! much appreciated

[@IRONMAN-kb4su]

OMG glad my DRZ/SM 400 is easier then that wow . Front cover is just over sprocket not motor , that sucks . Great how to loved it so detailed !

[@TDubsKid]

yeah most bikes you remove a plastic cover then you can remove the front sprocket in like 5 minutes haha. oh well hopefully the new sprockets and chain will last till 30k miles. thanks! glad you enjoyed it 😀

[@osfbg9901]

Good stuff Mate. Subscribed.

[@TDubsKid]

Thanks!

[@mongosaqqara]

I just changed mine...15/47 I enjoy the motor being a bit smoother wot...Great Video Kid!

[@TDubsKid]

+MongoSaqqara RadCats nice! Glad to hear 😃

[@martymartian9820]

So this is old, but I thought I would put in my 2 cents worth on the many sprocket change discussions. I read the pros and cons to different set ups so I finally settled on one. These changes are all according to each person's needs. The hard core mainly off roader will want to be lower geared. The highway guy will be the opposite. Me, I'm 71 and am in the middle. I do ride all kinds of terrain but won't put the little bike through things not designed for. So I need to ride road to trails and run around on black top. So I simply went 45 on the back. All it did was what I wanted. A little less vibration at 50-60 mile an hour and I'm sure a bit of a rpm drop. I hated the sound of it needing a 6th gear. I get to go a little farther in first. One of my long hills to come home is about 8% so I have to shift from 5th to 4th nearer the top. Big deal. Over all, for me it's better than stock and hasn't changed where I go or use the bike. Of course I'm old lol

[@TDubsKid]

For sure,gotta find the balance for your particular needs, would be perfect if it had a 6th speed

[@Photonutubia]

Great tutorial! Thanks.

[@TDubsKid]

Glad it was helpful!

[@KF1]

Great work, man

[@TDubsKid]

Appreciate it!

[@bpascalis]

Excellent detail TDK. When I changed my rear sprocket I did not need to bend those tabs. All I did was remove the nut and the tabs keep the bolt from turning. Thanks for doing this as I am going to do 15t on the front so this really helps.

[@TDubsKid]

thank you! great idea. yeah it's a great setup

[@bpascalis]

@@TDubsKid 15/47 installed and its much better. Man that 14 is a tiny thing but at 2600 miles, it was still in good shape except very shiny in the valleys but the tips and sides were fine.

[@fryreartechnology7611]

Great video. I am thinking about upgrade from a Honda Ruckus I have been riding for the last 11 years to something a little more off-road capable. Awesome to see the ins-outs of this bike. I like small bikes lol

[@TDubsKid]

thank you! oh very nice, the TW200 will be much more capable indeed. haha same here

[@jusride7]

Lots of hard work . Mahalo

[@TDubsKid]

indeed, but definitely well worth it if it helps people

[@brewcider]

I broke my chain back in December before you posted this... thanks to this video I can finally fix my bike and ride again!

[@TDubsKid]

dang, how did that happen? no problem! hope your out riding again soon

[@brewcider]

@@TDubsKid at exactly 1000 miles my factory chain broke while i was riding alone in the middle of the desert... luckily someone saw it happened and gave me a ride back to my car... now researching getting an X chain and replacing both sprockets

[@TDubsKid]

dang, those stock chains are quite sketchy. mine would stretch like crazy even on short rides. my x ring chain hasn't even stretched slightly yet even after about 200 miles it's a great way to go

[@canaktas7881]

Great vid bro, appreciated.

[@TDubsKid]

thanks! no problem 😀

[@aaronwinter447]

Doing this in a few days as my daily commute involves a short section of 55mph for about 10mins and I just want that tiny bit so I'm going with that 6.4% using stock chain. Excellent explanation.

[@TDubsKid]

yeah should be perfect for that. good middle ground

[@aaronwinter447]

@@TDubsKid Did the rear sprocket swap in about 2 hours and ran the commute today. Holds speed now without feeling too buzzy or any issues. This video made it super easy! Thanks!

[@buscandolibertad6698]

wow man , you know how to work on your motorbike !! good video.

[@TDubsKid]

thanks man!

[@buscandolibertad6698]

@@TDubsKid any more videos coming up ?

[@TDubsKid]

welding video from when I had to repair my frame, then one on the jns headlights

[@buscandolibertad6698]

@@TDubsKid thanks 😉✌

[@HansPastor]

Maravilloso video! Thank you very much!!!

[@TDubsKid]

No problem!

[@rickvann3489]

Sharp cookie you are... I'm looking at getting on of these and my buddy too. Wanting to Ride the TAT

[@TDubsKid]

thanks, would be cool to ride some TW's on the TAT

[@robertschaap5342]

Brilliant video.Thanks

[@TDubsKid]

thanks! no problem