How To Replace Wheel Bearing & Hub 2006-11 Honda Civic

Buy Now!
New Wheel Hub from 1AAuto.com 1aau.to/ia/1ASHF00502
Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision. This video shows you how to install a new wheel hub and bearing on your 2006-11 Honda Civic.
This process should be similar on the following vehicles:
2006 Honda Civic
2007 Honda Civic
2008 Honda Civic
2009 Honda Civic
2010 Honda Civic
2011 Honda Civic
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXAA00013
• Phillips Head Screwdriver 1aau.to/oa/1AXAA00013
• 17mm Wrench 1aau.to/oa/1AXAA00010
• 10mm Socket 1aau.to/oa/1AXAA00017
• 12mm Socket 1aau.to/oa/1AXAA00015
• 17mm Socket 1aau.to/oa/1AXAA00015
• 19mm Socket 1aau.to/oa/1AXAA00043
• 32mm Socket 1aau.to/oa/1AAST00003
• Bearing Puller
• Brake Caliper Hanger 1aau.to/oa/1AXAA00084
• Hub Puller
• Needle nose pliers 1aau.to/oa/1AXAA00051
• Needle nose pliers 1aau.to/oa/1AXAA00052
• Pliers
• Ratchet 1aau.to/oa/1AXAA00016
• Socket Driver
• Torque Wrench 1aau.to/oa/1AXAA00044
• Brake Parts Cleaner
• Paper Towels 1aau.to/oa/1AXSS00035
• Rust Penetrant
• Chisel 1aau.to/oa/1AXAA00055
• Hammer 1aau.to/oa/1AXAA00091
• Pick 1aau.to/oa/1AXAA00037
• Wire Brush 1aau.to/oa/1AXAA00079
Subscribe: / @trq
Check out our playlist:
Honda Civic 2005-2011 8th Generation: • Honda Civic 2006-2011 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@karelltulod3079]

Amazing

[@123andme]

Two words, " loaded knuckles." I'll never look back and sweat over a stuck hub and inner race again and worry that pressing the hub back in is gonna damage the new bearing (because sometimes it does). In and out and then enjoy my day and not ruin my weekend.

[@lightningxx]

Yeah you cant get those for these cars unless you want to pay a small fortune. Rears yes, thats the way to go

[@purpledonatello]

Great stuff. I'm sure you don't like to promote bearing kits, but appreciated showing us how to use it. One step missing is probably removing the inner race.

[@modakaification]

Better to replace the whole hub assembly that comes with the bearings already. That way you can skip this whole hub bearing removal process.

[@SonnyWolfSmiles]

I didn't bother to do the wheel bearings the hard way , its easier to just replace the whole Hub , while replacing the wheel bearings I replaced both front CV axles, both inner and outer tie rods,sway bar , sway bar end links etc , the previous owner didn't have any maintenance done so i did everything as a precaution.

[@ethanortiz4824]

Doesn’t show how to put on hub and bearing puller tool on

[@tommyweaver3540]

Please list the maker of the tool you used to pull the bearing

[@billypat9370]

Awesome video. One question where can I find those pulley to remove the wheel bearing

[@stm4179]

I may continually miss it, but what is the axle nut's torque spec?

[@bigjohnson7415]

Seems like getting a hub/knuckle assy would be easier? For those of us who don't have access to the pullers you have.

[@Jerm353]

I agree the price for a hub assy is about the same and rarely goes out

[@lightningxx]

You can rent the puller for free at Oreillys

[@Scotty-2-Shotty]

Extremely helpful, ty

[@spitlera]

Great video. I think you were loosening the lug bolts in the very last scene??

[@MrCoursair77]

Dude, you forgot to disconnect your battery .. The ABS could possibly short out sensitive electrical …ABS wire

[@amarqasem]

Good job 👏

[@TrungNguyen-dg8qs]

what size socket is used for the removal hub tool cuz i busted two size sockets on my new tool set trying to get the bearing out

[@michaelw6645]

if youre doing this your abs wire is most likely rusted in there and not all sparkly new clean like his is. have a new wire ready to go it will almost certainly break on removal source: tsx uses same type abs wire and every one of mine were all rusted in and had to be broken and chiseled out to remove

[@hectorperez1528]

What are the exact bearing and knuckles puller and installer tools?

[@njvalue2]

What is the torque for the axle nut?? and how did you get the race off of the hub??

[@karelltulod3079]

Cool amazing

[@selegonzalez8398]

Guys i bought this exact Assembly from TRQ and now my ABS light is on. I did not put anytying on the magnetic side and made sure to put it in right. Idk why. Anyone have an idea?

[@adrew1963]

pretty tough job without specialty tools looks like

[@unclassifiedjz6885]

My hub has play after installing an oem bearing is this normal

[@123andme]

Hi. I had the same problem after I installed mine. Hub play... Sometimes when we press in a bearing the bearing gets loose. I'd just go but a loaded hub or loaded knuckle assembly.

[@sirelbey]

⭐⭐⭐⭐⭐

[@ianmckenzie4923]

Tie rod is not removed that easily

[@DillyDog94]

Oops, I put my bearing in backwards. ABS light is on now. Oh well, I should’ve watched the show video lol

[@TheMikevt]

wow, now do that on a vehicle in 20 years of salt roads

[@JuanGutierrez-hg1jc]

this is stupid if you cant put anihting on the magnetic side of the bearing how dou you keep it from faling apart ?????

[@boss_of_da_dead4189]

Lol how you tightened everything with impact wrench and then hit it with torque wrench after that makes no sense I’ll give you a few points on installation but for that my man you failed us mechanics

[@migmogg8087]

You can snug stuff down then use the torque wrench